Table of Contents
Advertisement
GETTING STARTED GUIDE
IVN-8561
100BASE-T1 Media Converter
This document describes how to begin using the IVN-8561 100BASE-T1 Media Converter.
The IVN-8561 is a two-channel, four-port media converter that converts data between
100BASE-TX Ethernet and 100BASE-T1 Automotive Ethernet with minimal latency.
Safety Guidelines
Operate the IVN-8561 only as described in this document.
Caution
injury.
Caution
Product misuse can result in a hazard. You can compromise the safety protection
built into the product if the product is damaged in any way. If the product is
damaged, return it to NI for repair.
This icon denotes a caution advising you to take precautions to avoid
Do not operate the IVN-8561 in a manner not specified in this document.
Advertisement
Table of Contents
Related Manuals for National Instruments IVN-8561
Summary of Contents for National Instruments IVN-8561
-
Page 1: Safety Guidelines
Caution Do not operate the IVN-8561 in a manner not specified in this document. Product misuse can result in a hazard. You can compromise the safety protection built into the product if the product is damaged in any way. If the product is... -
Page 2: Electromagnetic Compatibility Guidelines
Note For EMC declarations and certifications, and additional information, refer to Online Product Certification section. 2 | ni.com | IVN-8561 Getting Started Guide... -
Page 3: Online Product Certification
Verify the following components are in your kit. • IVN-8561, 100BASE-T1 Media Converter • USB cable assembly, Type-C (male) to Type-A (female), 1 m • Connector plug (QTY 2) • Screwdriver, 2 mm, flathead • Documentation IVN-8561 Getting Started Guide | © National Instruments | 3... -
Page 4: Power Requirements
The power connector is USB Type-C. Use the USB cable (Type-C to Type-A) included with the IVN-8561 to power the device from a standard USB 3.0 port on your computer or industrial controller. The IVN-8561 can be powered from the USB port of any NI PXI, CompactRIO, or industrial controller. -
Page 5: Cabling Requirements
100 Mbit link speed is the defauilt setting. This LED will be on steady even when no cable is attached. 10 Mbit link speed is not supported. If this LED is off, packets will not pass through. IVN-8561 Getting Started Guide | © National Instruments | 5... -
Page 6: Master/Slave Switches
To establish a link between two 100BASE-T1 ports, one port must be configured as master and the other as slave. The IVN-8561 allows you to establish a link with a port in any configuration by selecting the appropriate mode with the front panel switch. -
Page 7: Wiring The Ivn-8561
Wiring the IVN-8561 Terminal block headers are used to connect to the 100BASE-T1 ports. Compatible plugs are included with the IVN-8561. Attach these plugs to twisted pair cabling to connect a 100BASE-T1 network to ports 1 or 3 of the IVN-8561. -
Page 8: Connecting The Ivn-8561
100 Mbit link speed must be selected for ports 2 and 4, indicated by the LED next to the port. Connect one end of the USB power cable to the IVN-8561, and connect the other end to a standard USB 3.0 port. -
Page 9: Functional Diagram
The IVN-8561 provides two channels to convert data between 100BASE-TX Ethernet and 100BASE-T1 Automotive Ethernet. Each channel consists of one port for 100BASE-T1 communication and one port for 100BASE-TX communication. -
Page 10: Worldwide Support And Services
NI trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering NI products/technology, refer to the appropriate location: Help»Patents in your software, the file on your media, or the National Instruments Patent Notice at . You can find patents.txt ni.com/patents...
Need help?
Do you have a question about the IVN-8561 and is the answer not in the manual?
Questions and answers