Honeywell Lyric LCP300-L Quick Installation Manual

Lyric® Gateway Lyric® Gateway
Lyric® Gateway Lyric® Gateway
This Quick Installation Guide provides the basic steps to quickly and easily install the Lyric Gateway Residential
Burglar and Fire Alarm Control Panel, using the built-in programming defaults.
Before you begin Before you begin
Before you begin Before you begin
The Gateway can be connected to the internet via a hardwire connection or wirelessly via the premise's Wi-Fi®
router. Programming is done via AlarmNet 360™ using a Smart (Mobile) Device or a laptop computer.
For Wireless Installations the following are required: For Wireless Installations the following are required: For Wireless Installations the following are required: For Wireless Installations the following are required:
A smart device with the AlarmNet 360 App loaded or a laptop (referred to as 'the set up device'). The App will
•
be used to connect the Gateway panel to the customer's router onsite.
Settings on the customer's smart device(s) must be set for Wi-Fi operation (Wi-Fi enabled).
•
Access to the customer's router SSID and WPA or WPA2 password (typically located on the router's label)
•
Have the customer download the MyHome Gateway and the TotalConnect® 2.0 apps from the iOS or Android
•
App Store, iTunes or Play Store to any additional smart devices. The system supports up to eight smart devices.
If you are not signed up for AlarmNet 360, click on "Dealer Signup" from the login screen to gain access to the
•
Honeywell web-based programming.
Dealer Sign Dealer Sign- - - - Up Direct Link Up Direct Link: https://services.alarmnet.com/AlarmnetDirectP_SignUp/Submission_Agree.aspx
Dealer Sign Dealer Sign Up Direct Link Up Direct Link
Before starting the installation process, open the AlarmNet 360 App or go to the AlarmNet 360 website
(www.AlarmNet360.com)
Installation Summary Installation Summary
Installation Summary Installation Summary
1. Create an AlarmNet 360 account for the Lyric Gateway.
2. Install and power up the Gateway (refer to the Installing the Lyric Gateway section)
a. If using a Cellular Communications module, install the module before powering up the Gateway.
b. Connect Gateway and smart devices(s) to the premises router (Wi-Fi or Ethernet) if available.
c. The Gateway automatically registers with AlarmNet 360 (inactive changes to active).
3. Complete the installation and programming; sync the Gateway and AlarmNet 360 (if necessary).
4. Download the MyHome Gateway and TotalConnect 2.0 apps to the customer's smart device.
COVER
Installing the Lyric Gateway Installing the Lyric Gateway
Installing the Lyric Gateway Installing the Lyric Gateway
1. If used, connect the network cable to the RJ45 receptacle on the Gateway.
2. Connect the 110VAC, 60 Hz to 9 VDC, 2.5A Power Supply p/n 300-05763V1 (300-05763V1 –CAN Canada) to
the receptacle on the gateway.
3. Install the rear cover on the Gateway (if required) OR secure the rear cover/mounting bracket to a wall surface
and install the Gateway and secure it with the provided screw.
4. Plug the power supply into a 24-hour, 110VAC unswitched outlet. The Gateway's Red and Green arming LEDs
will blink alternately for approximately 2 minutes during power up.
5. If the Gateway's RJ45 ethernet connection is used, at the Gateway touchpad enter Installer Code + 31 to enter
AP Mode and proceed to Step 10.
6. If connecting via Wi-Fi proceed to Step 7. When power up is complete the Gateway will be in Access Point
[AP] mode.
Note: The AP mode will remain active for 30 minutes. If AP mode time has expired, enter the Master Code and 31 on the Note: Note: Note:
Gateway touchpad to reenter the AP mode.
7. If the customer's router is WPS-capable, at the Gateway touchpad enter Installer Code and 41. If not, proceed
to Step 10.
8. Press the WPS button on the customer's router.
800-21668 10/16 Rev D
COMMUNICATION
MODULE
Installing the Communications Module (If used) Installing the Communications Module (If used) Installing the Communications Module (If used) Installing the Communications Module (If used)

Quick Installation Guide

gw-keypad-010-V1
Ref: LCP300-L/LCP300-LC