1. Manuals
  2. Brands
  3. fully Manuals
  4. Indoor Furnishing
  5. Jarvis L-shaped standing desk
  6. Assembly instructions manual

fully Jarvis L-Shaped Standing Desk Assembly Instructions Manual

Hide thumbs Also See for Jarvis L-Shaped Standing Desk:
Table of Contents

Advertisement

Quick Links

Jarvis L-shaped standing desk
Assembly instructions
For assembly assistance,
visit fully.com/howtojarvis
or call 888-508-3725
or email support@fully.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Jarvis L-Shaped Standing Desk and is the answer not in the manual?

Questions and answers

Related Manuals for fully Jarvis L-Shaped Standing Desk

Summary of Contents for fully Jarvis L-Shaped Standing Desk

  • Page 1 Jarvis L-shaped standing desk Assembly instructions For assembly assistance, visit fully.com/howtojarvis or call 888-508-3725 or email support@fully.com...
  • Page 2 Thank you for choosing a Jarvis desk from Fully.

  • Page 3: Table Of Contents

    Cautions and use Before starting In the box Assembly Setup Custom settings Troubleshooting Reset procedure Using your own desk top Specs Contact...

  • Page 4: Before Starting

    Placing objects taller than 20” underneath the desk Jarvis is a registered trademark of Fully, Inc. will obstruct the desk’s movement and may result in physical damage. All rights reserved.
  • Page 5 In the box frame parts Frame End Bracket Frame End Corner Frame End–A Corner Frame End–B Center Rail Support Center Rails Foot Corner Leg Side Leg Corner Bracket Left Side Bracket Right Side Bracket Mending Plate Crossbar Noise Attenuation Pads electric parts Leg Cables Control Box...

  • Page 6: Assembly

    Assembly step 1 Before assembling your desk, we find it helpful to choose how you’d like your desk oriented, and decide whether you’d like the Memory Handset to be mounted on the left or the right. Lay your Desk Top on a padded workspace, top down, in the shape of an L. If you’d like the desk top to form an L to your left once built, align the smaller piece on the right side during assembly, and vice versa.
  • Page 7 step 2 Bracket Frame End Side Leg Short Machine Screw Insert one of the Side Legs (you have two of these, either one works here) into the Bracket Frame End. The bracket will eventually hold your Control Box, but you don’t need to worry about that yet. Secure the Bracket Frame End to the Side Leg by threading four (4) Short Machine Screws into the holes.
  • Page 8 step 3 Frame End Side Leg Short Machine Screw Insert the remaining Side Leg into the Frame End. Thread four (4) Medium Machine Screws into the holes. As before, don’t tighten all the way until all four screws are in place.
  • Page 9 step 4 Left Side Bracket Step 3 Assembly Right Side Bracket Medium Machine Screw Select the Side Bracket that corresponds with your chosen Handset placement. If you’d like your Handset on the left, use the Left Side Bracket here; for the right side, choose the Right Side Bracket. Our illustration shows the Right Side Bracket.
  • Page 10 step 6 Corner Leg Short Machine Screw Corner Frame End–A Noise Attenuation Pad Apply two Noise Attenuation Pads to Corner Frame End–A, avoiding the screw hole. Insert the Corner Leg into the Corner Frame End–A. Attach the Middle Frame End to the Center Leg by inserting two (2) Short Machine Screws into the holes on the side of the leg without a crossbar mounting plate.
  • Page 11 step 7 Step 6 Assembly Corner Frame End–B Long Machine Screw Attach the Corner Frame End–B to the Corner Leg Assembly from Step 6 with two (2) Long Machine Screws. Now tighten all the screws from Steps 6 and 7.
  • Page 12 step 8 Step 7 Assembly Corner Bracket Long Machine Screw Noise Attenuation Pad Apply two (2) Noise Attenuation Pads between the three screw holes on the Corner Bracket. Use two (2) Long Machine Screws to attach the Corner Bracket to the outer edge of the Corner Leg Assembly.
  • Page 13 step 9 Large and Small Desk Tops Mending Plate Wood Screw Refer to the images on page 3 to confirm that the upside-down Desk Top will result in your desired orientation when flipped over. Place a Mending Plate over the seam between the two Desk Tops, and use four (4) Wood Screws to attach the plate through the pre-drilled holes in the Desk Top.
  • Page 14 step 10 Side Leg Assembly Desk Top Desk Top Machine Screw x4 Wood Screw Locate the Side Leg Assembly that includes the Pro Tip: If you have one of our tops with the Bracket Frame End (from Step 4). Next you’ll attach threaded screw inserts, you’ll use the Machine it to the Desk Top on the side where you want the Screws that came packaged with the desk top.
  • Page 15 step 11 Corner Leg Assembly Center Rails Center Rail Support Slide the two (2) Center Rails into the Bracket Frame End you just attached to the Desk Top. Orient the Rails so the cut-out slots face each other, and are on Center Rail orientation the top side of the Center Rails, as shown.
  • Page 16 step 12 Desk Top Machine Screw x5 Wood Screw Use five (5) screws to attach the Corner Leg Assembly to the Desk Top. Insert all screws part way before tightening them completely.
  • Page 17 step 13 Side Leg Assembly Center Rails Slide the remaining two (2) Center Rails into the Reminder: If you’re attaching the second leg to Corner Frame End attached to the Desk Top. Again, your large top at this point, as in orientations A you’ll orient the Center Rails so the cut-out slots and D (see page 3), now is the time to add your face each other and are on the top side of the Rails.
  • Page 18 step 14 Desk Top Machine Screw x5 Wood Screw Secure the final Side Leg Assembly with five (5) screws. Thread all screws part way. Once they are in place, tighten them completely.
  • Page 19 step 15 Short Machine Screw Warning: It might be tempting to skip this step. Center both pairs of Center Rails between the But don’t! Doing so will result in stability issues. Frame Ends. Use twenty (20) Short Machine Screws to lock the Center Rails down firmly.
  • Page 20 step 16 Thick Machine Screw Crossbar Install both Crossbars to the mounting plates on the Pro tip: We find it easiest to start by partly thread- Side and Center Legs, adjusting the width to meet ing both top Thick Machine Screws into place each plate.
  • Page 21 step 17 Short Machine Screw Use four (4) Short Machine Screws to fix the Crossbars in place. step 18 Memory Handset Wood Screw It’s time to install your Handset. If you’re using a Jarvis Desk Top, there will be pre-drilled holes on both the left and the right sides for attaching your Handset.
  • Page 22 step 19 Leg Cables Control Box Power Cable Slide the Control Box onto the Control Box Bracket Pro Tip—Cable Management: Cable Clips work on the Bracket Frame End. The “M” sockets should best when they are adhered directly to the metal face the closest leg.
  • Page 23 step 20 Foot Medium Machine Screw Loosely attach a Foot to one of the Side Legs using four (4) Medium Machine Screws. Once all screws are in place, tighten them completely, working in an X pattern. Repeat to attach the other Foot to the other Side Leg. If you are planning to use Braking Casters with your Jarvis Desk, remove all five Leveling Glides from the feet and thread the Braking Casters in their place at...
  • Page 24 21 Double check that all of the screws on the desk are fully tightened. Failure to install and tighten all screws may result in instability. step 22 With a friend (or a few), lift the desk and gently flip it onto its feet, supporting both the top and the frame of the desk.

  • Page 25: Setup

    Setup Initial calibration Before you start using your desk normally, you’ll need to get all the parts synced. Don’t worry, it’s easy. 1. Press and hold the DOWN button until the display reads RST (looks like “ASΓ”). Release. 2. Press and hold the DOWN button again, this time until the desk first lowers slightly, then rises slightly, and finally stops.
  • Page 26 By default, the Jarvis frame and handset are set to allow the maximum range of motion, from a fully re- tracted Lifting Column, to a fully extended one. If you would like to set a higher minimum height, or a lower maximum height, you can do that! Before starting, make sure the desk is plugged in, and the LED display is showing a number.
  • Page 27 Toggle between One Touch and Constant Touch presets Your programmable handsets allow your desk to remember your favorite height settings. By default, if you press and release a memory preset button, the desk will move on its own to the programmed height. You can change this behavior so that the desk will only continue to move to the programmed height with contin- ued pressure on that preset number.

  • Page 28: Troubleshooting

    Fully. If there is a difference in height between the two legs that exceeds 1.5”, stop the reset procedure and contact Fully. If the Memory Preset Handset displays “HOT”, let the desk cool down for 20 minutes. Reset procedure CAUTION: this will override any custom lower limit you might have set! Please ensure proper clearance for the Lifting Columns to retract fully.

  • Page 29: Using Your Own Desk Top

    Using your own desk top There’s no one right way to position your frame on your desktop but there are a few things you’ll want to keep in mind. Generally speaking, the desktop should be centered over the frame side-to-side, and posi- tioned slightly forward of center (towards the user) front-to-back.
  • Page 30 5. Create the final Frame End assembly with the remaining Frame End and Side Bracket. 6. Slide this new assembly onto the Center Rails from Step 4, and position them as you did with the origi- nal Frame End Assembly in Step 3. The example below shows a desk top that is 27” deep on either side and 56”...

  • Page 31: Specs

    1.5” per second Operating noise <50dB w/o top Load capacity 1500N Duty cycle and additional info 10% with max 2 mins on, 18 mins off Soft start/stop Adjustable Leveling Glides 4 Memory Presets Contact Fully Portland, Oregon 97214 888-508-3725 support@fully.com www.fully.com...
  • Page 32 Desks, chairs & things to keep you moving version 90.014.01.0085v.j...

Table of Contents

Save PDF