Table of Contents
Advertisement
MAINTENANCE
Once a Month
•
Test the door balance. Manually operate door. If it is unbalanced or binding, call a trained
door systems technician.
•
Check to be sure door opens and closes fully. Adjust limits and/or force if necessary.
•
Test both the safety reversal system and the safety beam sensor system as shown on
page 37 of this manual.
Once Every Six Months
•
Check the chain tension. Turnbuckle should be slightly above the rail. Adjust chain tension
as shown on page 15 of this manual.
•
Once a Year
•
Oil the door rollers, bearings and hinges.
Automatic Opening/Closing Force Adjustment
The opener will adjust the opening and closing force automatically so it operates at the most
efficient setting. To allow the opener to adjust the opening and closing force automatically,
operate the opener once after setting travel limits.
To operate the opener:
•
Press the push button to open the door, until it reaches the
fully open position.
•
Press the push button to close the door completely, until it
reaches the fully closed position.
You have now finished setting the opening and closing force.
NOTE:
• After adjusting the Up/Down travel limits, the opener will re-adjust its opening and closing force during
the first opening and closing cycle. Therefore, it is important to pay attention not to obstruct the door
during the first opening and closing cycle after adjusting the travel limits. The opener has now finished
adjusting the opening and closing force.
• During the force adjustment, do not obstruct the door's travel or the safety beam sensor.
In order to readjust the opening/closing force, you must first enter travel limit adjustment.
Force adjustment will proceed automatically after travel limit adjustment sequence.
Press
47
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the 046-0265-2 and is the answer not in the manual?
Questions and answers
Why won’t my garage door close with the remote?
The MasterCraft garage door opener may not close with the remote for several reasons:
1. Safety Reversal System Issue: The state-of-the-art safety reversal system might be detecting an obstruction near the door. Check for any objects or debris blocking the sensors.
2. Remote Control Programming: The remote may not be properly programmed. Follow the programming steps in the manual to ensure the remote is correctly paired with the opener.
3. Erased Remote Controls: If all remotes were erased (e.g., by holding the [SET] button for 15 seconds), you need to reprogram the remote.
4. Door Reinforcement Requirement: If the door is lightweight or not properly reinforced, it may not operate correctly. Check if a door reinforcement kit is required.
5. Battery or Remote Issue: Ensure the remote has working batteries and is functioning correctly.
Verify these potential causes to diagnose the issue. If the problem persists, contact the helpline at 1-800-689-9928.
This answer is automatically generated
How to install the wall console of mastercraft
To install the wall console for MasterCraft part number 046-0265-2:
1. Position the Wall Console: Place it at least 5 feet (1.5 meters) above the finished floor or the topmost step.
2. Ensure Proper Location: Install it within sight of the garage door, out of children's reach, and away from all moving parts.
3. Connect the Wires: Attach the bell wires to the two terminal screws. The wires are not polarity sensitive.
4. Secure the Console: Fasten it to the wall using two screws.
5. Safety Precautions: Ensure the power is not connected before installation.
Follow all warnings and placement guidelines to ensure safe operation.
This answer is automatically generated
with tension on chain how do you get the chain guide together
To assemble the chain guide on a MasterCraft 046-0265-2 with tension on the chain:
1. Insert Trolley Guides: Insert the trolley guides into the chain traveller until you hear a click, ensuring the chain traveller is fully seated.
2. Connect the Chain Assembly: Attach the two ends of the chain assembly at the turnbuckle.
3. Hand-Tighten the Turnbuckle: Rotate the turnbuckle by hand to connect it to the threaded shaft. Do not rotate the threaded shaft to prevent twisting the cable.
4. Secure the Locknuts: Once the desired tension is achieved, tighten the locknuts.
5. Adjust Chain Tension: Hold the threaded shaft with pliers and use a flat screwdriver to twist the turnbuckle. Tighten the chain until it is 1/3" (8 mm) above the base of the T-rail.
6. Final Check: After installation, some chain drop may occur when the door is fully closed.
This ensures proper chain tension and prevents twisting or damage to the cable.
This answer is automatically generated
My door stop about 1 inch from the bottom how to adjust it
Can you replace the light if it is not working