CYBEX CLOUD Q Manual
  1. Manuals
  2. Brands
  3. CYBEX Manuals
  4. Car Seat
  5. Cloud Q
  6. Manual

CYBEX CLOUD Q Manual

Hide thumbs Also See for CLOUD Q:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual , Instruction Manual
CLOUD Q
Infant Carrier - Birth to 12 months (approx.)
Instructions for Installation and Use
IMPORTANT: KEEP THIS BOOKLET IN THE STORAGE
COMPARTMENT ON THE CHILD RESTRAINT

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CLOUD Q and is the answer not in the manual?

Questions and answers

Related Manuals for CYBEX CLOUD Q

Summary of Contents for CYBEX CLOUD Q

  • Page 1 CLOUD Q Infant Carrier - Birth to 12 months (approx.) Instructions for Installation and Use IMPORTANT: KEEP THIS BOOKLET IN THE STORAGE COMPARTMENT ON THE CHILD RESTRAINT...

  • Page 2: Table Of Contents

    INTRODUCTION............................WARNINGS AND IMPORTANT SAFETY INFORMATION................CHILD HEIGHT RELATIVE TO HEIGHT MARKERS.................. NEXT STAGE OF RESTRAINT TO BE USED..................... OVERVIEW OF THE CLOUD Q INFANT CARRIER..................OVERVIEW OF THE BASE.......................... OVERVIEW OF THE TOP TETHER STRAP....................SUITABLE FOR USE............................ USING THE INFANT CARRIER........................

  • Page 3: Introduction

    INTRODUCTION ENGLISH To be used only in a rearward-facing position until the infant’s shoulders reach the shoulder height marker (approximately 12 months of age). Continue to use this infant restraint until the child reaches this limit. Infants are at risk of serious injury if they face forward too early. ARABIC CHINESE 12个月的宝宝）。...
  • Page 4 INTRODUCTION (Continued) GREEK Να χρησιμοποιείται μόνο σε θέση στραμμένο προς τα πίσω μέχρι οι ώμοι του βρέφους να φτάνουν στο δείκτη ύψους ώμου (περίπου 12 μηνών). Συνεχίστε να χρησιμοποιείτε αυτό το σύστημα συγκράτησης νηπίων μέχρι το παιδί να φτάσει σε αυτό το όριο.Τα βρέφη κινδυνεύουν με σοβαρό τραυματισμό αν κοιτάζουν...
  • Page 5 (See Page 27) Full Recline Backrest: A new function of the Cloud Q is that it can be changed to a full recline position when used outside of the car. With an extended leg-rest and a fully reclining backrest, the child can lie comfortably...

  • Page 6: Warnings And Important Safety Information

    WARNINGS • Use the restraint exactly as shown in the instructions. • Supervision of children is needed because they may be able to undo the buckles. • DO NOT LEAVE CHILDREN UNATTENDED IN THE CAR. • Do not alter or modify this restraint. •...
  • Page 7 IMPORTANT • Do not use the child restraint facing forwards. Do not use excessively upright or reclined. • The restraint should not be purchased or sold as a second hand item. It is recommended not to use child restraints older than 6 years as the protection in an accident may be reduced. •...

  • Page 8: Child Height Relative To Height Markers

    CHILD HEIGHT RELATIVE TO HEIGHT MARKERS HEIGHT MARKERS The Infant Carrier is not suitable for your child when their shoulders are above the shoulder height marker. If the babies neck muscles are unable to support their head then the child should remain rear facing, choose a child restraint that will take larger babies in rear facing.

  • Page 9: Next Stage Of Restraint To Be Used

    NEXT STAGE OF RESTRAINT TO BE USED When your child has outgrown the seat, you can then use one of the following restraints: 1 - Convertible Child Seat If the convertible seat is suitable for approximately 12 months then continue to keep your child rear facing until their shoulders reach the lowest marker.

  • Page 10: Overview Of The Cloud Q Infant Carrier

    OVERVIEW OF THE CLOUD Q INFANT CARRIER Carry Handle TOP VIEW No Rethread Harness Adjuster Headrest Shoulder Pads (removable) Canopy (Stored position) Shoulder Height Marker L.S.P device (fully extended) Travel System Release Button Carry Handle Adjustment Button Harness Straps Infant Insert...
  • Page 11 OVERVIEW OF THE CLOUD Q INFANT CARRIER Recline Release Handle BOTTOM VIEW Tether Loop Attachment Point L.S.P. device (stored) Base Attachment Rod Carry Handle Adjustment Buttons Travel System Attachment Slot Owner's Manual (Stored) Harness Base Attachment Rod Harness Adjustment Strap...

  • Page 12: Overview Of The Base

    OVERVIEW OF THE BASE FRONT VIEW Level Indicator (hidden) Locking Lever Infant Carrier Attachment Lock Belt Tensioning Plate Leveling Foot Belt Guide Steel Chassis Infant Carrier Attachment Catch Infant Carrier Release Green Safety Button...
  • Page 13 OVERVIEW OF THE BASE (Continued) REAR VIEW Level Adjustment Handle Belt Tensioning Plate Locking Lever Leveling Foot (fully extended)

  • Page 14: Overview Of The Top Tether Strap

    OVERVIEW OF THE TOP TETHER STRAP Top Tether Attachment Hook Top Tether Strap Top Tether Storage Pocket Tether Adjuster Tether Loop Attachment Hook Tether Loop Tether Loop Attachment Point Tether Loop Storage Pocket...

  • Page 15: Suitable For Use

    SUITABLE FOR USE The purchaser should check the measurements between the front of the seat back of the rear seat and all front seats in the car in which the child restraint is intended to be used, to ensure that the space is sufficient. The Infant Carrier MUST NOT TOUCH the front seat of the car.

  • Page 16: Using The Infant Carrier

    USING THE INFANT CARRIER - HANDLE POSITIONS The Handle has six LOCKED positions: 1. DRIVE position 2. INTERMEDIATE position 3. CARRY position 4. INTERMEDIATE position 5. INTERMEDIATE position 6. RESTING position To move handle to a new position, squeeze BOTH Handle Adjustment Buttons (one on each side) while rotating handle...

  • Page 17: Integrated Canopy & Infant Insert

    USING THE INFANT CARRIER - INTEGRATED CANOPY & INFANT INSERT INTEGRATED CANOPY Simply pull forward to extend the Cloud Q Canopy. The Canopy has four positions. To retract the Canopy, gently push it back into its original position. INFANT INSERT The Infant Insert will help provide a better harness fit for smaller babies, as well as stability for the torso.

  • Page 18: Adjusting The Seat

    The car seat may be adjusted up and down through eleven positions to perfectly fit your baby The Cloud Q is shipped in the lowest position with the Infant Insert already in position. 1. Unbuckle the Harness 2.

  • Page 19: Securing The Child

    USING THE INFANT CARRIER - SECURING THE CHILD 1. Loosen Harness by firmly pressing down on the Harness Adjustment Button while pulling forward on both straps at shoulder level 2. Press red button on Harness Buckle to release Tongues. 3. Place child in Infant Carrier in seated position making sure their bottom is in the seat, and their back is fully supported.
  • Page 20 USING THE INFANT CARRIER - SECURING THE CHILD (Continued) 6. Pull up on Harness Straps to snug around the child's hips while holding the Harness Buckle in place. 7. Slowly pull the adjuster strap to tighten the Shoulder Straps. A snug strap should not allow any slack.

  • Page 21: Using The Infant Carrier Outside Of The Vehicle

    USING THE INFANT CARRIER OUTSIDE OF THE VEHICLE ADJUSTING THE RECLINE POSITION A new function of the Cloud Q is that it can be reclined to RECLINED MODE an almost horizontal position outside of the car. With an extended leg-rest and a fully reclined backrest, the child can lie comfortably and in an ergonomically correct position.

  • Page 22: Adjusting The Recline Angle Using The Base

    ADJUSTING THE RECLINE ANGLE USING THE BASE It is very important for your child's safety that this child restraint be installed at the correct recline angle. Before attaching the Infant Carrier to the Base, always check the Level Indicator for the correct recline angle range based on your child’s weight.

  • Page 23: Installing The Base Using A Lap And Shoulder Belt

    INSTALLING THE BASE USING A LAP AND SHOULDER BELT 1. Position Base on a rear vehicle seat. 2. Adjust the Leveling Foot to achieve the correct angle range for your child's weight as shown on the Level Indicator. See page 21 3.
  • Page 24 INSTALLING THE BASE USING A LAP AND SHOULDER BELT (Continued) 6. On the buckle side, first lift up on the shoulder belt to remove slack in the lap belt . Then remove slack from the shoulder belt on the opposite side At this point, only remove slack from the vehicle belts, being careful not to over tighten them.

  • Page 25: Attaching Infant Carrier To Base In The Car

    ATTACHING INFANT CARRIER TO BASE IN THE CAR 1. Make sure handle is LOCKED in the CARRY position. 2. Lift Infant Carrier by the Handle and slide the Attachment Rod under the Attachment Catch on the Base, and rotate foot end of the Infant Carrier down onto the Base until an audible CLICK is heard.
  • Page 26 ATTACHING INFANT CARRIER TO BASE IN THE CAR (Continued) 4. Unroll the Tether Loop from the Tether Loop Storage OVERVIEW OF THE TOP TETHER STRAP Pocket and place it around the Infant Carrier. Pull to 5. Connect the Tether Loop with the Attachment Hook. remove slack 6.

  • Page 27: Releasing Infant Carrier From Base

    RELEASING INFANT CARRIER FROM BASE If used, retract the L.S.P. device. See page 27 1. Disconnect the Tether Loop from the Attachement Hook 2. Roll the Tether Loop and place it in the Tether Loop Storage Pocket 3. Move the carry handle into the CARRY position 4.

  • Page 28: Using The Linear Side-Impact Protection (L.s.p.)

    The L.S.P. telescopes out to two positions, fully extended and intermediate. Pull out the L.S.P. device on the side of the Cloud Q adjacent to the vehicle door or panel listening for an audible CLICK. If the L.S.P. device is touching the door or panel, retract the L.S.P.

  • Page 29: Care And Cleaning

    D. Ensure the buckle is free of fluff, liquid or other matter that may enter the buckle slots. Clean the buckle if it is sluggish to engage. E. If any part of the restraint is cracked, broken or not operating seek repair immediately contact the CYBEX distributor at: Australia: CNP Brands New Zealand: Wainhouse Distribution...

  • Page 30: How To Clean Your Infant Carrier

    If the buckle is not operating or you do not hear a strong audible CLICK when tongues are inserted then the buckle may need to be replaced. Contact the Cybex distributor at CNP Brands: 1300 667 137 (Australia), or Wainhouse Distribution: 0800 567 5000 (New Zeland):...

  • Page 31: Cleaning The Cover

    - Do not pull sticky items from covers as the cover may be damaged - soak in water and gently remove. VERY IMPORTANT Only replace the cover with CYBEX supplied replacement cover with identical shoulder height markers or a replacement cover meeting AS/NZS 8005.

  • Page 32: Removing And Reinstalling The Seat Cover

    CARE AND CLEANING (Continued) REMOVING AND REINSTALLING THE SEAT COVER BACKREST COVER The integrated Harness System cannot be removed from the seat. NEVER remove or attempt to remove parts of the Harness System. DO NOT damage, remove or dispose of any EPS foam. NEVER use Infant Carrier without a properly installed Seat Cover.

  • Page 33: Accessories

    ACCESSORIES SHOULDER PADS The Shoulder Pads provide a more comfortable fit for the infant while it sits inside the carrier. Those removable soft pads protect the sensitive areas around the neck, shoulders arms and chest of the infant, by avoiding immediate contact with the harness.

  • Page 34: Installation Of Car's Upper Anchorage Point

    INSTALLATION OF CAR’S UPPER ANCHORAGE POINT FOR CARS FITTED WITH A CHILD RESTRAINT UPPER ANCHORAGE POINT Locate the upper anchorage point behind the rear seating position. (Consult the car owners handbook for the location of the upper anchorage point). The upper anchorage point should be directly behind and central to the restraint. Remove thread plug from the parcel shelf / floor / roof, etc.

  • Page 35: For Cars Not Fitted With A Child Restraint Upper Anchorage Point

    INSTALLATION OF CAR’S UPPER ANCHORAGE POINT (Continued) FOR CARS NOT FITTED WITH A CHILD RESTRAINT UPPER ANCHORAGE POINT For Sedans only - Drill 9mm diameter hole in the parcel shelf on the centre line of the seating position as shown in Figure 2. Install the anchor bolt as shown in Figure 3 (next page). It is recommended that this installation be carried out by a child restraint fitting station or licenced motor mechanic.
  • Page 36 INSTALLATION OF CAR’S UPPER ANCHORAGE POINT (Continued) FIGURE 3. UPPER ANCHORAGE FITTINGS FOR SEDANS ONLY WARNING: CHILD RESTRAINTS MUST NOT BE ATTACHED TO UNSOUND METAL OR Attachment bolt TO WOOD, OR SYNTHETIC STRUCTURES. Anchor fitting WHEN DRILLING THE 9 mm HOLE DO NOT DRILL THROUGH FUEL LINES, FUEL TANKS, Spacer(s) Front of vehicle...

  • Page 37: Warranty

    WARRANTY The following warranty applies solely in the country where this product was initially sold by a retailer to a customer. 1. The warranty covers all manufacturing and material defects, existing and appearing, at the date of purchase or appearing within a term of three (3) years from the date of purchase from the retailer who initially sold the product to a customer (manufacturer’s warranty).
  • Page 38 CNP Brands Wainhouse Distribution 20 Calarco Drive, VIC, 3030, 2-6 Argyle St, Morningside, Australia PO Box 41-014, St Lukes, Auckland Customer Service: 1300 667 137 New Zealand info@cnpbrands.com.au Customer Service: 0800 567 5000 helpline@wainhousedist.co.nz Series Number Cloud Q AUS CY_171_2749_A0717...

Table of Contents

Save PDF