Gainsborough e50 Installation Manual
  1. Manuals
  2. Brands
  3. Gainsborough Manuals
  4. Plumbing Product
  5. e50
  6. Installation manual

Gainsborough e50 Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

E50 instructions :Layout 1

18/11/14
10:41
Page 1
e50
Installation guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the e50 and is the answer not in the manual?

Questions and answers

Related Manuals for Gainsborough e50

Summary of Contents for Gainsborough e50

  • Page 1: E50 Instructions :Layout

    E50 instructions :Layout 1 18/11/14 10:41 Page 1 Installation guide...
  • Page 2 E50 instructions :Layout 1 18/11/14 10:41 Page 2...

  • Page 3: Table Of Contents

    E50 instructions :Layout 1 18/11/14 10:41 Page 3 Contents Important information - Safety information - Pipework connections - Isolating valves - Siting - Pressures - Pressure relief device Components Pipework installation Electrical installation - Mains voltage connection - Electrical rating...

  • Page 4: Important Information

    E50 instructions :Layout 1 18/11/14 10:41 Page 4 Important information THIS INSTALLATION AND USER GUIDE IS DESIGNED TO ENSURE THE SAFETY OF THE INSTALLER AND USER AND THE OPERATION/RELIABILITY OF THE PRODUCT. FAILURE TO OBSERVE THESE MAY CAUSE A HAZARD, DAMAGE THE PRODUCT AND INVALIDATE YOUR GUARANTEE.

  • Page 5: Isolating Valves

    E50 instructions :Layout 1 18/11/14 10:41 Page 5 Isolating valves A suitable full bore isolation valve must be fitted to the incoming supply in accordance with the current water supply regulations and our terms of warranty. The isolation valve must be sited in an accessible location for service and maintenance purposes.

  • Page 6: Components

    E50 instructions :Layout 1 18/11/14 10:41 Page 6 Components...

  • Page 7: Pipework Installation

    E50 instructions :Layout 1 18/11/14 10:42 Page 7 Pipework Installation instructions In addition to the guide that follows it is essential that the written instructions on pages 4 and 5 are read and understood, and that you have all the necessary components before commencing installation. Failure to install the product in accordance with these instructions may adversely affect the warranty terms and conditions.

  • Page 8: Electrical Installation

    E50 instructions :Layout 1 18/11/14 10:42 Page 8 Pipe work connection must be made using a suitable 1/2” female fitting. Either a 1/2” tap connector or 1/2” to 15mm push fit type connector (not provided) is recommended. This product is suitable for use with plastic pipe provided the manufacturer has certified suitability for use with the intended fitting.

  • Page 9: Mains Voltage Connection

    E50 instructions :Layout 1 18/11/14 10:42 Page 9 Switch must be outside Switch must Zone 2 be outside Zone 2 2.25m 2.25m 0.6m 0.6m 0.6m 0.6m YOUR ATTENTION IS ALSO DRAWN TO THE SAFETY INFORMATION DETAILED WITHIN THE IMPORTANT INFORMATION SECTION AND THE ELECTRICAL RATING SECTION.

  • Page 10: Electrical Rating

    E50 instructions :Layout 1 18/11/14 10:42 Page 10 BEFORE ANY ELECTRICAL CONNECTION IS ATTEMPTED, THE ELECTRICITY SUPPLY MUST BE TURNED OFF AT THE MAINS SWITCH. FAILURE TO DO SO COULD RESULT IN ELECTROCUTION. The shower unit must only be fitted to a 230-240V ac supply.

  • Page 11: Wiring Installation

    E50 instructions :Layout 1 18/11/14 10:42 Page 11 If upgrading to a higher kW shower it is essential to ensure that the electrical circuit, including the wiring and isolating switches are adequate for the increased load. Notes:- 1. Cable selection is dependant on de-rating factors detailed in the notes below.

  • Page 12: Earth Bonding

    E50 instructions :Layout 1 18/11/14 10:42 Page 12 Place the service tunnel onto the shower unit ensuring it fits flush with the shower unit back plate. Earth bonding The installation must be earth bonded in accordance with current regulations. Where earth bonding of the premises is not evident, it may be necessary to run a bonding cable back to the earth terminal at the consumer unit.
  • Page 13 E50 instructions :Layout 1 18/11/14 10:42 Page 13 If required, slide the soap dish onto the rail under the handset holder. Fit the rail into the rail end bodies. Secure the rail assembly to wall using the fixings provided, if suitable, ensuring the rail and rail end bodies remain firmly engaged.

  • Page 14: Front Cover Installation And Shower Commissioning

    E50 instructions :Layout 1 18/11/14 10:42 Page 14 Front cover installation and shower commissioning This shower must be fully commissioned following the procedure detailed below before use. Failure to do so could damage the shower and invalidate the guarantee. Carefully offer the front casing onto the back plate assembly ensuring the wires are not trapped.

  • Page 15: Thermal Trip

    E50 instructions :Layout 1 18/11/14 10:42 Page 15 Handset to hose assembly Ensuring the hose washer is in the correct position, connect the hose to the handset, taking care not to overtighten and place into position within the handset holder.
  • Page 16 E50 instructions :Layout 1 18/11/14 10:42 Page 16 E50 - functions key Start/stop button Heat setting knob Flow/temperature control Power LED Overheat LED Low flow LED...
  • Page 17 E50 instructions :Layout 1 18/11/14 10:42 Page 17 E50 - user guide E50 user instructions 1 Turn on power to the shower unit. ! Usually a pull cord type isolator switch. ! The power light will illuminate. 2 Set the temperature/flow control knob to the full cold position.
  • Page 18 E50 instructions :Layout 1 18/11/14 10:42 Page 18 E50 - shower head operation Shower head operation ! NEVER ATTEMPT TO MAKE ANY ADJUSTMENT TO THE SHOWER HEAD BY PULLING ON THE SHOWER HOSE. 1 To select the desired spray pattern, rotate the shower spray cassette clockwise or anti-clockwise.

  • Page 19: User Guide

    E50 instructions :Layout 1 18/11/14 10:42 Page 19 User guide Please refer to the separate user guide booklet provided. After installation Inspection & maintenance In the interest of safety, we recommend this product and its electrical installation are checked by a qualified electrician at least every 2 years.

  • Page 20: Trouble Shooting Guide

    E50 instructions :Layout 1 18/11/14 10:42 Page 20 Trouble shooting guide ! These checks must only be performed by a competent person. Warning! There are no user serviceable components beneath the cover of the appliance. IF YOU ARE UNABLE TO REMEDY THE PROBLEM WITHOUT REMOVING THE COVER, YOU SHOULD CONTACT YOUR INSTALLER OR A QUALIFIED ELECTRICIAN.
  • Page 21 E50 instructions :Layout 1 18/11/14 10:42 Page 21...
  • Page 22 E50 instructions :Layout 1 18/11/14 10:42 Page 22...
  • Page 23 E50 instructions :Layout 1 18/11/14 10:42 Page 23...
  • Page 24 E50 instructions :Layout 1 18/11/14 10:42 Page 24...
  • Page 25 E50 instructions :Layout 1 18/11/14 10:42 Page 25...
  • Page 26 E50 instructions :Layout 1 18/11/14 10:42 Page 26...
  • Page 27 E50 instructions :Layout 1 18/11/14 10:42 Page 27...
  • Page 28 E50 instructions :Layout 1 18/11/14 10:42 Page 28...
  • Page 29 E50 instructions :Layout 1 18/11/14 10:42 Page 29...
  • Page 30 E50 instructions :Layout 1 18/11/14 10:42 Page 30...

  • Page 31: Approvals

    E50 instructions :Layout 1 18/11/14 10:42 Page 31 Approvals The Gainsborough E50 shower is manufactured in an ISO 9001:2000 registered factory and has been designed and tested to the very highest standards. It complies with all relevant international standards for safety and reliability.
  • Page 32 E50 instructions :Layout 1 18/11/14 10:42 Page 32 Gainsborough Bathroom Products Limited The Flyer’s Way Westerham Kent TN16 1DE Customer helpline: 01959 560760 Website: www.gainsboroughshowers.co.uk Email: enquiries@gainsboroughshowers.co.uk Part No: 115104 Issue 1 Nov 14 Please note that calls may be recorded for training and quality purposes The company reserves the right to alter, change or modify the product specifications without prior warning ®...

Table of Contents