Advertisement
Quick Links
Model Name: BZ600 ，BZ600RBA，BZ600GBA，BZ600GBA-I，BZ600RBA-I，BZ625，BZ625BGB，BZ625GEB，BZ625BGB-I，
BZ625GEB-I，BZ650，BZ650SBA，BZ650SBA-I
FCC ID: Z7RZ6
IC:10013A-Z6
Wireless Range
Enhanced Data Rate (EDR)
Advanced Audio Distribution Profile
(A2DP)1.2, Hands-Free Profile (HFP)
At least 10M (33 feet)
1.5, Headset Profile (HSP) 1.1
SBC Stereo Streaming(yes)AVRCP
Audio/Video Remote Control
Profile(yes)
Description
User Msnual
Supported Profiles
Usage
Password
NO password on V3.0 devices, On older
devices use "0000"
Change Password?
No !!
Response
Advertisement
Related Manuals for Braven BZ600gba
Summary of Contents for Braven BZ600gba
- Page 1 User Msnual Model Name: BZ600 ，BZ600RBA，BZ600GBA，BZ600GBA-I，BZ600RBA-I，BZ625，BZ625BGB，BZ625GEB，BZ625BGB-I， BZ625GEB-I，BZ650，BZ650SBA，BZ650SBA-I FCC ID: Z7RZ6 IC:10013A-Z6 Wireless Range Supported Profiles Password Change Password? Enhanced Data Rate (EDR) Advanced Audio Distribution Profile (A2DP)1.2, Hands-Free Profile (HFP) NO password on V3.0 devices, On older At least 10M (33 feet) 1.5, Headset Profile (HSP) 1.1...
-
Page 2: Pairing Mode
PAIRING - Press answer button for 5 seconds to go into pairing mode .White LED will be flashes 1 time every 0.4 seconds. PAIRED (CONNECTED): White LED will be flashes 1 time every 5 seconds .There is a sound at the same time when connection is made. Press for 5 seconds = GO INTO INCOMING CALL -Press answer button to answer call. - Page 3 As soon as button is pressed = Volume decrease one increment (there should be 16 increments) Press and hold for 2 seconds = To previous song Decrease Volume Volume Down At minumin volume = Beep at minimum volume(No Beep sound at minimum volume) When audio is inserted, the sound level should be controlled by the Stereo input...
- Page 4 As soon as button is pressed, The LED ring display the colors for Battery Check Button Shows amount of power in battery. every 30% of power as follows: 100-70% white, 35-70% Blue, 0-35% red. Use for connecting other speakers, Using 3.5mm to 3.5mm auxiliary cable (included), plug one end into Line-out Port when plugged into, the speaker will speaker and the other end into another speaker, to create more volume,...
- Page 5 After the first cell phone connected with speaker .The second cell phone start to connecting with speaker (Pairing method is same as the first cell phone):Press answer button for 5 seconds to go into pairing mode(The first cell phone is auto- disconnected with speaker at this moment ) .White LED will be flashes 1 time every 0.4 seconds.After connected.White LED will be flashes 1 time every 5 seconds .There is a sound at the same...
- Page 6 If speaker No connect with cell phone . The software setting is : When speaker is on but connected to a cell phone (not in use ). There is no any beeps or sounds until the speaker has not been in use for 29minutes and 50 seconds. then there are 3 beeps, and then turn off immediately . If a 3.5mm cable or USB cable is incerted into the unit it will not enter power saving mode unless the battery is less than 3.2V Note：This device complies with Part 15 of the FCC Rules: Operation is subject to the following two conditions: 1.
Need help?
Do you have a question about the BZ600gba and is the answer not in the manual?
Questions and answers