Toro TITAN HD Series Setup Instructions
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower
  5. TITAN HD Series
  6. Setup instructions
Toro TITAN HD Series Setup Instructions

Toro TITAN HD Series Setup Instructions

Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

TITAN
Model No. All models
Setup

Loose Parts

Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
9
10
11
12
13
Note: Determine the left and right sides of the machine from the normal operating position.
© 2016—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
HD Series Riding Mowers
Description
No parts required
No parts required
No parts required
No parts required
No parts required
No parts required
No parts required
No parts required
No. 2 lithium or molybdenum-based
grease (purchase separately)
Locknut (3/8 inch)
Carriage bolt (3/8 x 2-1/4 inches)
No parts required
No parts required
Operator's Manual
Engine owner's manual (non-Toro
engines)
Operator-training material
Key
Registration card
Register at www.Toro.com.
Form No. 3407-539 Rev A
Qty.
–
Remove the machine from the crate.
–
Add fuel to the machine.
–
Check the engine-oil level.
–
Service the hydraulic oil.
–
Check the tire pressure.
–
Servicing the battery.
Raise the rollover protection system
–
(ROPS).
–
Check the grass deflector.
1 tube
Check the machine for grease.
3
Install the right bumper (rear discharge
models only).
3
–
Check the mower adjustment.
Check the machine before delivery to
–
the customer (all machines).
1
1
Deliver the machine to the customer (all
1
machines).
2
1
Original Instructions (EN)
All Rights Reserved *3407-539* A
Printed in the USA
Setup Instructions
Use

Advertisement

Table of Contents
loading

Related Manuals for Toro TITAN HD Series

Summary of Contents for Toro TITAN HD Series

  • Page 1: Loose Parts

    Check the mower adjustment. Check the machine before delivery to – No parts required the customer (all machines). Operator's Manual Engine owner's manual (non-Toro engines) Deliver the machine to the customer (all Operator-training material machines). Registration card Note: Determine the left and right sides of the machine from the normal operating position.

  • Page 2: Removing The Machine From The Crate

    This machine is shipped filled with hydraulic fluid in the reservoirs. If removing the machine from a metal crate, refer to the Dealer/Distributor Portal for further information. Check the expansion tank; if necessary, add Toro ® HYPR-OIL ™ 500 hydraulic fluid, as recommended in the...

  • Page 3: Checking The Tire Pressure

    Checking the Tire Pressure No Parts Required Procedure Pressure: 13 psi (90 kPa) Figure 2 Note: Check the tire pressure before starting the machine. Refer to your Operator’s Manual for the correct tire type and procedure. Raising the Rollover Servicing the Battery Protection System (ROPS) No Parts Required No Parts Required...
  • Page 4 Checking the Grass Deflector No Parts Required Procedure If there are plastic ties holding the grass deflector up, remove them and lower the deflector into place. WARNING An uncovered discharge opening could allow the machine to throw objects in the operator's or bystander's direction and result in serious injury or death.
  • Page 5 Checking the Machine for Installing the Right Bumper Grease Parts needed for this procedure: Parts needed for this procedure: Locknut (3/8 inch) Carriage bolt (3/8 x 2-1/4 inches) No. 2 lithium or molybdenum-based grease (purchase 1 tube separately) Procedure Procedure Mount the side bumpers in the top holes when operating in height of cut higher than 64 mm (2-1/2 inches) and in the Before you use the machine, check the machine for grease;...

  • Page 6: Checking The Mower Adjustment

    Checking the Mower Adjustment No Parts Required Procedure Adjust the side-to-side level and the front-to-rear blade slope. Use the relevant procedures in the Operator's Manual to verify that the deck is level, and make any adjustments as necessary.
  • Page 7 Date: Delivering the Machine to the Customer (All Machines) Parts needed for this procedure: Operator's Manual Engine owner's manual (non-Toro engines) Operator-training material Registration card Procedure At delivery, fill in the model and serial number, complete the items listed in the following table, and initial each when finished.
  • Page 8 Make sure that the customer receives the Operator's Manual, engine owner's manual (non-Toro engines), Set Up Instructions, and operator training material. Make sure the customer knows that the Parts Catalog is available at www.Toro.com. Assist the customer in loading the machine.

Table of Contents