Page 5
• Trembling at the End When OHP Printing ................. page(4-32) • Poor Fusing Grade......................page(4-33) 4-6-4 Malfunction....................page(4-44) • No Power (LCD NO display LED Off)................page(4-36) • Fuser Error........................page(4-37) • Paper Jam (Mis-Feeding)....................page(4-38) • Paper Jam(Jam 1)......................page(4-39) • Engine Error........................page(4-40 4-6-5 Toner Cartridge Service ................page(4-41) Samsung Electronics...
Page 6
5-11. Drive Ass'y Exploded View & Parts List............page(5-26) 5-12. Main Frame Ass'y Exploded View & Parts List ..........page(5-28) 5-13. FuserAss'y Exploded View & Parts List............page(5-30) 5-14. Screw ......................page(5-32) 6. Block Diagrams ................page(6-1) 7. Connection Diagram ..............page(7-1) Samsung Electronics...
6. Observe the original lead dress, especially near sharp edges, AC, and high voltage power sup- plies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Samsung Electronics...
2. Be sure to replace the battery with the same or 4. Dispose of used batteries according to the manu- equivalent type recommended by the manufac- facture’s instructions. turer. Samsung Electronics...
Cotton Swab Standard: Equipment to check the weight of consum- Standard: For general home use, for medical service. ables(toner cartridge) supplied by Samsung Electron- ics. (The gram unit can be measured.) Cleaning Equipments a IPA(Isopropyl Alcohol)dry cloth or a soft stuff neutral detergent.
Plain , Legal , Cardstock , Transparency Zoom Range ADF : 25~200 %(1% Step) NOTE : (1) Speed claims based on the test chart : Letter size. SDMP : Single Document Multiple Printout MDSP : Multiple Document Single Printout Samsung Electronics...
Page 13
Tone only user modeTone/Pulse selectable in tech mode. 2-7 Consumables Item Description Type Separate type (Toner Cartridge / Drum Cartridge) Life Toner Cartridge 6,000 sheets ( 5% coverage pattern, simplex normal mode ) Drum Cartridge 15,000 sheets (simplex normal mode ) Samsung Electronics...
5. Do not force to remove or planten plastic-material components. 6. Make sure all components are in their proper position. 3-2 Rear Cover 1. Remove the six screws securing the Rear Cover. 2. Separate the Rear Cover from the Base Frame and Scanner Ass'y. Samsung Electronics...
2. Remove the six screws and take out the Shield Main Upper. 5. Unplug the one connector from the Main Board and remove two screws. 3. Remove the three screws, as shown below. 6. Pull up the Scanner Ass'y in the direction of arrow. Samsung Electronics...
2. Remove the two screws securing the Scanner Ass'y. 3. Pull the OPE Ass'y as shown below. 6. Remove the Contact Rubber from the unit. 4. Unplug the two connector from the OPE Ass'y. 7. Remove the Key Pad from the unit. Samsung Electronics...
Page 17
- Rear cover (see page 3-1) - Scanner Ass'y (see page 3-2) - OPE Ass'y (see page 3-3) Cover Gear Link Tray 2. Open the ADF Upper Ass'y. 4. Remove the ADF Upper Ass'y, as shown below. ADF Upper Ass’y Samsung Electronics...
Page 18
5. Take out the Housing Upper ADF, as shown below. Housing Upper ADF 3. Push the part to the arrow direction (to the inner), unlatch the part to the arrow direction and remove Guide Lower Ass'y. Guide Lower Ass’y Samsung Electronics...
Page 19
5. Unlatch the Scan Roller gear part and remove it, as shown below. Scan Roller 6. Unlatch the ADF Roller gear part and remove it, 3. Remove the seven screws securing the ADF as shown below. Lower Ass'y. ADF Roller Samsung Electronics...
Page 20
11. Unlatch the Cover Switch and remove it, as Take out the CIS Ass'y. shown below. Cover Switch CIS Ass’y 12. Unlatch the both side and remove the Scan 9. Remove the one screw securing the CIS Bracket Board. and take out the CIS. CIS Bracket Samsung Electronics...
Tray-Case from the Tray Link. The Tray Link (inner side) locates at an angle of 45˚ from the Side Cover Ass’y and then remove the Tray Link. MP Tray Tray Link Tray-Case Samsung Electronics...
Page 22
1. Unite the part and home to the projection 1. Take out the Transfer Roller, as shown below. part of the Side Cover assembly, and widen them from each other to dissemble the Side Cover Ass’y. Deplex Ass’y Samsung Electronics...
3. Unplug the one connector. 7. After remove the two screw and open the Lower Ass’y froward tack out the Heat Roller Ass’y from Upper Fuser Ass’y. 4. Remove the three screws and take out the Fuser Ass'y. Heat Roller 3-10 Samsung Electronics...
- Rear Cover (see page 3-1) - Scanner Ass'y (see page 3-2) - Side Cover Ass'y (see page 3-8) 2. Take out the Cover rr Ass'y , as shown below. Cover Rear Ass’y 4. Pull the Exit Ass'y and remove it. Samsung Electronics 3-11...
1. Before you remove the Cover Paper Exit Ass'y, 2. Remove two screws and Cover Paper Exit Ass'y, you should remove: as shown below. - Rear Cover (see page 3-1) - Scanner Ass'y (see page3-2) Cover Paper Exit Ass’y 3-12 Samsung Electronics...
- Rear Cover (see page 3-1) - Shield Main Upper (see page 3-2) 2. Unplug the two connectors. (Main Motor:9pin, Duplex Solenoid : 2pin) Dust Fan 4. Remove the five screws and take out the Drive Ass'y. Drive Ass’y Samsung Electronics 3-13...
- Side Cover Ass'y (see page 3-8) - Exit Ass'y (see page 3-11) - Cover Paper Exit Ass'y (see page 3-11) 2. Remove three screws and take out the Shield SMPS Upper. 4. Remove the SMPS, as shown below. SMPS 3-14 Samsung Electronics...
3. Remove the three screws and take out the LSU. - Rear Cover (see page 3-1) - Scanner Ass'y (see page 3-2) - Side Cover Ass'y (see page 3-8) - Exit Ass'y (see page 3-11) 2. Unplug the two connectors. Samsung Electronics 3-15...
Dummy Scan Lower. Dummy Base Frame Cam Jam Remove 5. Remove the seven screws and take out the Main Frame Ass'y. Main Frame Ass’y Front Cover 3. Remove the Locker Deve. Cover Motor Bracket Lock Deve 3-16 Samsung Electronics...
Disassembly and Reassembly * Cover Exit Rear 1. Remove the one screw and take out the Panel 2. Remove the one screw and Cover Exit Rear, as Connect MPF. shown below. Cover Exit Rear Samsung Electronics 3-17...
Disassembly and Reassembly * MP Ass'y 1. Unplug the two connectors. 3. Release the SMPS fit. Pull the MP Ass'y Upward and remove it. MP Ass’y 2. Remove the four screws and take out the Dummy Cover. Dummy Cover 3-18 Samsung Electronics...
1. Unplug the three connectors. 3. Remove the four screws and take out the Pick Up Ass'y, as shown below. 2. Remove the two screws and take out the Cas- sette Rail. Guide Paper Out Pick-up Ass’y Cassette Rail Samsung Electronics 3-19...
2. Remove the five screws and take out the Main Main Lower. PBA from the Shield Main Lower. Main PBA Shield Main Lower 3. Remove the one screw and unlatch the LIU PBA securing the Main PBA and remove it. LIU PBA Main PBA 3-20 Samsung Electronics...
In this chapter, it was mentioned about the functions for maintaining the product, how to find the causes of the inferiority, and troubleshooting method. The service manual is bound the SF-835P and SF-830 together in one volume. The SF-835P has functions such as printer, copy, scanner, and fax.
15000 print pages. NO CARTRIDGE When the machine detected the toner cartridge has Install the Cartridge. not been installed. BYPASS JAM When the machine detected the non-feeding from Open the side Cover and clear the jam. BYPASS Tray. Samsung Electronics...
Page 36
Camp & Thermostat. Heating Error During operation, Temperatare does not go up. Check thermister contact point & Heating Lamp. Scanner Locked Scanner is locked by locker. Check locker. Connect the Flat-Cable. Samsung Electronics...
To return to normal user mode, press MENU, #, 1, 9, 3, 4 in sequence again, or turn the power off, then on by unplugging and plugging the power cord. Options changed while in service mode do not remain changed unless you clear the machine’s memory. Samsung Electronics...
TX JOURNAL (Memu + One-touch20) The same as User Mode. RX JOURNAL (Memu + One-touch21) The same as User Mode. HELP LIST (Memu + One-touch22) MSG. CONFIRM SCHEDULE JOB PHONE BOOK SYSTEM DATA TRANSMISSION RECEPTION HELP LIST PROTOCOL ERROR CODE Samsung Electronics...
2. Push the ENTER button. 3. Select you country. 4. Push the ENTER button then it will be all memory clear. . NOTICE : Always perform the memory clear after replace the main board. Otherwise, the system may not operate properly. Samsung Electronics...
3. After the scan, CCD SHADING PROFILE will be print out. 4. If the printed image is different to the image, the CCD is defect. NOTICE : When you test CCD, make sure that the cover is closed. < ADJUST SHADING > Samsung Electronics...
Page 42
It is needed in the production progress. Service person doesn't need to use it. ROM TEST Use this feature to test the machine'S ROM. The result and the software version appear in the LCD display. • FLASH VER : 1.00 V • ENGINE VER :1.00V Samsung Electronics...
Page 43
PROGRAM DIAL It is a function setting transmitting conditions to transmit to specific address preliminary. When user transmit specific address set this function, the conditionsapplied automatically. 4-10 Samsung Electronics...
It lists all telephone numbers that have been stored in the machine. SCHEDULE JOB This list shows a specific information on the documents currently stored for delayed transmission. It provides the operation number, starting time, type of operation, etc. ERROR CODE It shows error history occurred using product. Samsung Electronics 4-11...
1. sending and receiving fax must be the same model. 2. A sending fax must be set up as ECM mode, and a receiving memory must be set up as 100%. If not, the function operates abnormally. 4-12 Samsung Electronics...
Method : Press MENU, #, 1, 9, 3, # in sequence.Firmware version is displayed on LCD. FLASH VER : 1.00 ENGINE VER : 1.00 Press 1( in the number keypad) : The LCD display shows "Updated date" Press 2( in the number keypad) : The LCD display shows "Product first use date" Samsung Electronics 4-13...
When the function is on, sentence to explain the condition of engine is printed in the below section of the printing output. It is needed in the development progress. Service person doesn't need to use it.4-7 Troubleshooting 4-14 Samsung Electronics...
1. LSU light power normal? 1. Check the rated level and replace. 2. Bias voltage output is high? 2. Set to power rating. 3. Video data is always supplied? 3. Replace defected board. Digital Printer Digital Printer Samsung Electronics 4-15...
Page 49
2. The toner cartridge is out of position? 2. Checkand adjust. Partial blank image 1. Develope roller scar or particle. 1~2. Replace toner cartridge. (periodic) 2. Scar or particle. (94 mm) 3. Transfer roller scar or particle . 3. Replace transfer roller. (47 mm) 4-16 Samsung Electronics...
Supply Roller 35.8 mm Horizontal dark band Develope Roller 44.8 mm Horizontal dark band Transfer Roller 57.8 mm Black side contamination/transfer fault Heat Roller 82.5 mm Black spot, White spot Pressure Roller 69.1 mm Black side contamination Samsung Electronics 4-17...
LSU transit to High/Low the defective component when printing? or board The mirror in LSU might be misplaced so the light path to the OPC deviates ->Repair or replace LSU or remove any defective matters in the machine Samsung Electronics 4-18...
Page 52
This could occurs when he power of LSU is low or life the density is low due to the obstacles on the window -> Replace LSU or clean the window Replace the toner cartridge 4-19 Samsung Electronics...
-> Repair or replace the boards Replace LSU Is charge voltage supplied Repair or replace HVPS from HVPS? Is the Hsync/ signal received Replace LSU in LSU? Charge part's contact is bad -> Repair or replace toner cartridge Samsung Electronics 4-20...
OPC of Check both if the toner cartridge's developer and LSU prevent the counter is over its guaranty and path -> Remove the obstacles amount of the toner material -> Replace the toner cartridge 4-21 Samsung Electronics...
Toner over supply due to the Works adjustment fault of metering correctly after blade in developer replaced LSU? -> Replace developer The power of LSU is set high or internal problem -> Replace LSU or adjust volume Samsung Electronics 4-22...
Check if the LED of PTL in front of the transfer roller is on when it presses the top cover switch on purpose -> If not, replace PTL Internal blade or supplying part of the developer is defective -> Replace the toner cartridge 4-23 Samsung Electronics...
OK? (-300V) HVPS Operating/storage There may be a problem in toner temperature is too low or layer control in toner cartridge not recommended -> Replace the developer paper used? Use the machine with recommended paper and at condition Samsung Electronics 4-24...
Check toner is stuck onto since the obstacles toner material dropped the P/R or H/R in fuser stuck to charge roller onto the paper -> -> Clean it or replace -> Clean the Charge Roller Replace the developer and then reprint. 4-25 Samsung Electronics...
(38mm) -> Repair/replace HVPS, developer The OPC is damaged due to Heat roller is ruined the irregular transfer voltage -> Replace the roller of HVPS -> Repair/replace HVPS -> If the same problem persists, replace the developer Samsung Electronics 4-26...
Bad images Any obstacles supply from developer around the no image on the PTL lamp? -> Replace developer area? Light distortion due to Clean the window of PTL the mirror ruined or LSU's diffused reflection -> Replace LSU 4-27 Samsung Electronics...
Obstacles stuck on OPC's D/R in developing unit has surface the defect -> Clean the OPC and -> Replace the developer machine or replace developer When putting in/out the developer, scratch is made -> Replace the developer Samsung Electronics 4-28...
Other parts are touching the When multi-page OHP printng, fan and prevents it from less than 10 films are revolution guranteed. (Reduce the -> Check and repair number of films and re-insert after paper check LED if off) 4-29 Samsung Electronics...
3 Kg) 3.5mm? Replace the control The paper used is too component on Main thick or contains too much cotton in it -> Re-test with the Check any contact recommended paper problem in thermistor and repair Samsung Electronics 4-30...
Clean around fuser. 2. Paper is curled in the exit cover?. 2. Check locking works wells. Watch whether the ribs of exit cover hace any burr or resisitive edge. If they do, remove obstacles or replace. 4-31 Samsung Electronics...
Page 65
1. Check whether the Reg. sensor is working or not. ADF. 2. Check whether the Feed Roller is working or not. Does it curl while coming out? 1. Check the Open Cover whether there are bosses. 2. Check the ADF ass'y is well assemble. Samsung Electronics 4-32...
-> Replace the boards Repair/replace the Remove the shortage Detect failure due to the board which detects side board or replace the board cover open or switch error -> Replace the board or switch 4-33 Samsung Electronics...
If not check the CN4 on the power board. The voltage of pin #60 of U36 Thermistor, connecting point or engine (CPU) on the Main PBA board defect -> Repair/replace the is about 2.65V when component/board printing? Samsung Electronics 4-34...
Switch them Does the Pull out the Paper end curled? extender pulled out? extender <Recommendation> Use the recommended Use the MPF for the thick and quality paper paper such as envelope and cardstock 4-35 Samsung Electronics...
Adjust the paper guides to fit the or sensitive paper to paper width is grounded Check static electricity? the shutter prevents feeding The force of springs pressing the developer is weak -> Check guide-DEVE Use the recommended paper Samsung Electronics 4-36...
(Main B'D to LSU) Check Main B'D CN7-9, Replace Main PBA P_MOTOR Signal Check Main B'D CN7-8, Replace LSU LREADY Signal Check Main B'D CN7-4, Replace Main PBA LDON Signal Check Main B'D CN7-1, Replace LSU HSYNC Signal 4-37 Samsung Electronics...
Page 71
4-7-3 Toner Cartridge and Drum Cartridge Service It is not guaranteed for the default caused by using other toner and Drum Cartridge cartridge other than the cartridge supplied by the Samsung Electronic or caused by non-licensed refill production. Precautions on Safe-keeping of the Drum Cartridge Excessive exposure to direct light more than a few minutes may cause damage to the cartridge.
2. Check whether it could be recycled. contaminated with toner. (1)Check whether foreign sub- stances or toner are stuck to the terminal (contact point) of the developer. (2)Check whether the state of the terminal assembly is normal. 4-39 Samsung Electronics...
Page 73
(contact point) of the cled over 2 times. developer. (2)If toner nearly being expired are col- (2)Check whether the state of the lected to use, it is judged as the recycled terminal assembly is normal. developer. Samsung Electronics 4-40...
Page 74
Clean the terminals of the nal(point of contact) of the charged roller, then recheck it. developer and the state of assembly. (Especially check the charged roller terminal.) 4-41 Samsung Electronics...
Turn the PC and printer off, and reboot the system to print again. If not solved, double-click the printer in my computer If the regular fonts are not printed this time again. the cable must be defective so replace the cable with new one. Samsung Electronics 4-42...
Before choosing the document, the menu is still inactive. Or put the document out of the list and repeat the routine as in the above or finish the spool manager. 4-43 Samsung Electronics...
Page 77
Exploded Views and Parts List Appendix information The following list shows different materials by model. The material codes mentioned in themanual are subject to change without prior notice. For the latest exact information, see ITSELF SYSTEM. (http://itself.sec.samsung.co.kr) PMO-COVER DUMMY OPE JC72-00858D PBA SUB-LIU JC92- •SCX-5312F/XAA...
Page 78
JC96-02429G ELA HOU-SCANNER JC96-02447E ELA HOU-OPE COVER ASS’Y JC96-02430G ASS’Y(SEC) PMO-OPE COVER JC72-00796G ELA HOU-PLATEN ASS’Y(SEC) JC96-02445E PCT-ONETOUCH PAPER JC72-00872G ELA HOU-OPE COVER ASS’Y JC96-02444E PCT-LCD WINDOW JC72-00870G PMO-OPE COVER JC72-00944E PMO-COVER DUMMY OPE JC72-00858G PCT-LCD WINDOW JC72-00945E Samsung Electronics...
Exploded Views and Parts List 5-1. Main Exploded View & Parts List Samsung Electronics...
Page 81
SHEET FEED JC72-00078A PBA SUB-LIU JC92-01355A ONLY SF-835P PMO-DUMMY BASE FRAME JC72-00789A IPR-SHIELD MAIN LOWER JC70-00245A PMO-COVER FEED AY JC72-00801A PMO-COVER BRKT MOTER JC72-00834A PMO-GUIDE PAPER OUT JC72-00835A SHEET-CONNECTOR JC63-00072A O : Service available X : Service not available Samsung Electronics...
Page 82
MEA UNIT-HOLDER GND ASS’Y JC97-01574A 53-1 SPRING ETC-TR_R JC61-70906A 53-2 PMO-BUSH JC72-40228A 53-3 PMO-HOLDER GEAR TR JC72-00884A MEA ETC-COVER REAR ASS’Y JC97-01620A 54-1 PMO-GUIDE-EXIT-OPEN JC72-00939A 54-2 PMO-COVER REAR JC72-00915A OPTIONAL O : Service available X : Service not available Samsung Electronics...
Exploded Views and Parts List 5-6. Side Cover Ass’y Exploded View & Parts List 1-4 1-4 11-4 1-10 1-11 1-10 1-12 10-2 10-7 10-3 10-4 10-6 10-5 10-1 5-14 Samsung Electronics...
Page 93
LABEL(R)-HEIGHT,MP JC68-00697A CBF HARNESS-OPE GND JC39-00036A PMO-TIE STOPPER JC72-00766A IPR-BRKT GROUND B JC70-00230A IPR-BRKT GROUND TR JC70-00231A IPR-BRKT GROUND A JC70-00232A IPR-BRACKET GUIDE B JC70-00234A PMO-BUSHING FEED JC72-00730A O : Service available X : Service not available Samsung Electronics 5-15...
Exploded Views and Parts List 5-7. Cassette Ass’y Exploded View & Parts List 5-16 Samsung Electronics...
Page 95
PMO-GUIDE REAR JC72-00717A PMO-GUIDE/SIDE CST JC72-40967D PMO-LOCKER PLATE JC72-41210A PRP-PAD CST JC73-10910A SPRING ETC-LOCKER PLATE JG61-70531A SPRING ETC-PLATE K/UP JC61-00455A LABEL(R)-INSTRUCTION CST JC68-00692A LABEL(R)-HEIGHT CST JC68-00709A PMO-IMPACT CASSETTE JC72-00877A O : Service available X : Service not available Samsung Electronics 5-17...
Exploded Views and Parts List 5-8. Exit Ass’y Exploded View & Parts List 5-18 Samsung Electronics...
Page 97
PMO-HOLDER EXIT ROLL JC61-00547A PMO-ROLLER FD F JC72-41007A PMO-ROLLER FD R JC72-41008A SPRING ETC-EXIT LOWER IDLE JC61-00484A MEC- BRUSH ANTISTATIC JC75-00095A PBA SUB-BIN-FULL SENSOR JC92-01400A RING-C 6044-000159 PMO-LEVER STACKING JC72-00709A O : Service available X : Service not available Samsung Electronics 5-19...
Exploded Views and Parts List 5-9. Feeder Ass’y Exploded View & Parts List 5-20 Samsung Electronics...
Page 99
PMO-ROLLER FEED L JC72-40261A SPRING-FEED CAST JC61-00480A PMO-HOLDER PINCH M JC72-00724A PMO-SUB HOLDER FEED JC72-40266A SPRING ETC-FEED MP JC61-00481A WASHER-PLAIN 6031-000021 PMO-ROLLER FEED S JC72-40262A IPR-SHAFT FEED IDLER JC70-10230A O : Service available X : Service not available Samsung Electronics 5-21...
JC70-00241A PMO-BASE FRAME JC72-00779A PMO-BRACKET PUSH DEVE JC72-00780A PMO-BRACKET SIDE OPEN JC72-00781A PMO-COVER FRONT DUMMY JC72-00785A ELA M/MEDIO AUD-SPEAKER JC96-01607A IPR-GROUND PLATE SCF JC70-00243A CBF HARNESS SCF JC39-00082A O : Service available X : Service not available 5-24 Samsung Electronics...
PMO-PTL PATH JC72-00822A PMO-SHAFT PICK UP JC72-00729A RPR-RUBBER PICK UP JC73-00086A SPRING-PICKUP JC61-00482A PBA SUB-FEED+P.EMP SEN. JC92-01363A PBA SUB-PTL JC92-01361A PBA SUB-TONER_TX JC92-01359A PICK UP, CSTAS (FRU) JC81-00428A O : Service available X : Service not available Samsung Electronics 5-25...
Exploded Views and Parts List 5-14. Main Frame Ass’y Exploded View & Parts List 29.30 5-28 Samsung Electronics...
Page 107
JC66-40211B GEAR-EXIT,IDLE(Z17) JC66-40964A CBF-HARNESS THERMISTOR_JOINT JC39-00164A PMO-HOUSING TERMINAL JC72-41010A IPR-TERMINAL FU JC70-10961A PMO-CAP CONNECTOR L JC72-00463A PMO-CAP CONNECTOR U JC72-00465A ELA HOU-MOTOR GND JC96-01579A SPRING-CLUTCH JB61-70922A RING-CS 6044-000001 O : Service available X : Service not available Samsung Electronics 5-29...
3P X 2EA 33.6Kbps 600 / / 600 PAPER ATING UNICON TX : RX LINE1 DMA I/F PART I/F PART ADF OPTION EXTER NAL EXTERNAL PHONE LINE PHONE INTE RFACE INTERFACE CENTRONICS PART CABLE CCD MODULE USB CABLE Only SCX-5312F Samsung Electronics...
Page 114
11. D P 12. GN D_5 T EL LI N E SENSOR SWITC H 3. +24V 3. GND _5 13. RE CA LL 14. nE_DP 4. +24VS FOR LS U + 5V S C U T (ONLY SCX-5312F) Samsung Electronics...
This manual is made and described centering around circuit diagram and circuit description needed in the repair center in the form of appendix. Samsung Electronics Digital Printing CS Group Copyright (c) 2002. 02...
Page 119
8. nHOOK2 9. n RI NG _DET 7, 8. DGND 2. +5VS 10. +5V 11. DP 12. GND_5 T EL L IN E SW ITCH SF-830 3. +24V 1. +5V 13. RE CALL 14. nE_DP 4. +24VS SENSOR 2. S INAL...
Page 121
Output Signal KS32C61200 nRESET 29F800B nRESET • POWER ON/OFF DETECT VCC RISING/FALLING 4.5°≠4.6V RESET TIME (Td) 1.48~1.52ms • Td=(Ct*V sensing)/I charge (...Ct=33µF, Is=100µA) 2) TIMING CHART and SENSE Threahold Voltage 3.6V RESET Output Output Undefined Undefined Repair Manual Samsung Electronics...
Page 122
PHBTT8, 8 mA DATA19 " CPU Data Bus 19 " DATA20 " CPU Data Bus 20 " DATA21 " CPU Data Bus 21 " Vddi 3.3 V DATA22 Input CPU Data Bus 22 PHBTT8, 8 mA Repair Manual Samsung Electronics...
Page 123
TAP Controller Data In " TAP Controller Clock " TAP Controller Data Out PHOB4 AVdd Vcca Analog 3.3 V AVin[0] Analog Input 0 PICA AVin[1] Analog Input 1 " AVss Vssa Analog Gnd AVssAVin[2] Analog Input 2 PICA Repair Manual Samsung Electronics...
Page 124
Parallel Port Data PHBTT8, 8 mA " Parallel Port Data " nSTROBE Data Strobe PHIL, ST Vsso 5 V Gnd RxD1 / CTin[2] Uart 1 Rx Data PHIL, ST TxD1 Uart 1 Tx Data PHOB4, 4 mA Repair Manual Samsung Electronics...
Page 125
PHIL, ST nCMSG / PWM[2] Com. Busy / PWM [2] PHOB4, 4 mA Vddo nDRAMCAS0 DRAM Cas Strobe 0 PHOB8, 8 mA nDRAMCAS1 " DRAM Cas Strobe 1 " nDRAMCAS2 " DRAM Cas Strobe 2 " Repair Manual Samsung Electronics...
Page 126
3.3 V DRAMD9 Input DRAM Data Bus 9 PHBTT12, 12mA DRAMD10 " DRAM Data Bus 10 " DRAMD11 " DRAM Data Bus 11 " Vssp 5 V Gnd DRAMD12 Input DRAM Data Bus 12 PHBTT12, 12mA Vddp Repair Manual Samsung Electronics...
Page 127
DRAM Data Bus 31 " Vsso 5 V Gnd DRAMA0 DRAM Address Bus 0 PHOB8, 8 mA DRAMA1 " DRAM Address Bus 1 " DRAMA2 " DRAM Address Bus 2 " DRAMA3 " DRAM Address Bus 3 " Repair Manual Samsung Electronics...
Page 128
Address Bus 5 for ROM PHOB8, 8 mA ADDR6 " Address Bus 6 for ROM " ADDR7 " Address Bus 7 for ROM " Vssi 3.3 V Gnd ADDR8 Address Bus 8 for ROM PHOB8, 8 mA Repair Manual Samsung Electronics...
Page 129
3.3 V Gnd for PLL Charge Pump Out : FILTER POBA Capacitor is connected CPU Test Mode : CPUTEST PHILD50, ST Tied to Gnd nRESET Reset Input PHIL, ST nRSTOUT Reset Output PHOB8, 8 mA Repair Manual 3-10 Samsung Electronics...
Page 130
LED will scroll and the PROGRAM DOWNLOAD MODE will be activated. In this mode, you can download the pro- gram through the parallel port. MCLK A23-2 nROMCS ACC+1 SETUP HOLD <Write Timing Diagram for Two Beat Burst Cycle> Repair Manual 3-11 Samsung Electronics...
Page 131
DRAMOE*SIGNAL, when reading. You can expand up to 64MBYTE of DRAM in this sys- tem. 0xf f f f f f f bank3 Next bank3 Bas e bank2 Next bank2 Bas e bank1 Next bank1 Bas e bank0 Next bank0 Bas e 0x0000000 <DRAM Bank Configuration> Repair Manual 3-12 Samsung Electronics...
Page 132
While configuring the software, you must set the timing register of SFR considering the clock speed and the DRAM spec. dat a wait dat a wait addr 5Mhz MCLK nRAS nCAS column address column address r ow address DRAMA dat a 0 dat a 1 DRAMD Tcas Tcas <FPM Read Timing Diagram> Repair Manual 3-13 Samsung Electronics...
Page 134
While configuring the software, you must set the timing register of SFR considering the clock speed and the DRAM spec. addr wait dat a dat a wait 5Mhz MCLK nRAS nCAS column r ow address column DRAMA data 0 data 1 DRAMD Tcas Tcas <EDO Read Timing Diagram> Repair Manual 3-15 Samsung Electronics...
Page 135
Tcas <FPM Write Timing Diagram> Tcas clock type cycle # register cycle # register cycle # register 40 ns EDO 50 ns EDO 58Mhz 60 ns EDO 70 ns EDO <SFR Values Example for FPM> Repair Manual 3-16 Samsung Electronics...
Page 136
D0-D7 are 8-bit data buses. RS0-RS4 signals to select the register in modem chips. /RS and /WR signals control READ and WRITE respectively. /IRQ is a signal for modem interrupt. Transmission speed of FM336 is supported up to 33.6k. The modem is connected to LINE through transformer directly. < FAX TRANSCEIVER > Repair Manual 3-17 Samsung Electronics...
* VDDBIAS is connected to the system’s 5.0V supply to provide 5V tolerance on I/O signal pins (including all inputs, outputs, and bidirectionals). in systems where 3.3V signaling only is used, connect VDDBIAS to a 3.3V supply. Repair Manual 3-19 Samsung Electronics...
Table presents the PM-22’s DC characteristics. IMPORTANT : CLOCK pin timing is measured at TTL levels, not CMOS. The system CLOCK driver must be configured cor- rectly in order to ensure that duty cycle and Vil specifications are met. Repair Manual 3-20 Samsung Electronics...
Page 141
• OD : Open drain output • P : Power supply Combinations indicate bidirectional pins. An “H” in the Resistor column indicates the pad has an internal pull-up resistor. A tilde (~) indicates no internal resistor. Repair Manual 3-22 Samsung Electronics...
Page 142
Interfac e CPU I/F CIP3 SRAM Mod ule Regis ter 1 024 x 8 n CS n RD n WR A [ 5 : 0] D [ 15 : 0] n XDREQ n XDACK <Block Diagram> Repair Manual 3-23 Samsung Electronics...
Scaling of input image (1) Scaling factor • Horizontal direction : 25 ~ 800% by 1% unit • Vertical direction : 25 ~ 100% by 1% unit (2) Scaling data memory : 2x8Kx8bits = 128Kbits (internal) Repair Manual 3-24 Samsung Electronics...
Page 144
ADD R- BUS ADDR- BUS Ana lo g Si gn al PI_TG Scanner PI1 , PI2 Tx_A, Tx_B, DAT A- BUS DAT A- BUS n Tx_A, nTx_B CIP3 D OCU MENT IMAGE <External interface with CIP3> Repair Manual 3-25 Samsung Electronics...
Page 145
Contro l Mo to r nTX_A, B Con tro l TX_EN1, EN2 Interface CPU I/F CIP3 SRAM Mod ule Register 1 024 x 8 nRD nWR A[5:0] D [15:0] nXDREQ nXDACK <Block diagram of CIP3> Repair Manual 3-26 Samsung Electronics...
Page 146
PC are all processed through this part. PPD( 7: 0) DATA BUSY nSTROBE nACK <Compatibility Hardware Handshaking Timing> Repair Manual 3-27 Samsung Electronics...
Page 147
6. Peripheral sets nACK high. This is the edge that should be used to clock the data into the host 7. Host sets nAUTOFD low to indicate that it is ready for the next byte 8. The cycle repeats, but this time it is a command cycle because BUSY is low Repair Manual 3-28 Samsung Electronics...
Page 150
‘nHSYNC’ signal (pulse) and the CPU forms the left margin of the image using this signal (horizontal synchronous signal). Repair Manual 3-31 Samsung Electronics...
It is the process to change the afterimage on the OPC drum surface formed by LSU into vis- ible image by the toner particles. While the supply roller energized with -450V by HVPS and the developer roller energized with -300V rotate in the same Repair Manual 3-32 Samsung Electronics...
Page 152
3) Bias Output (Enable) Unit: DEV (Development Voltage)/Supply(Supply Voltage)/BLADE(Blade Voltage) 4) Transfer ‘+’ Output (Enable) Unit: THV(+)(Transfer High Voltage(+)) 5) Transfer ‘-’ Output (Enable) Unit: THV(-)(Transfer High Voltage(-)) 6) Switching Unit 7) Feedback Unit 8) Regulation Unit 9) Output Unit Repair Manual 3-33 Samsung Electronics...
Page 153
<Transfer Output Unit Block Diagram> MHV-PWM REGULATION TRANS SWITCHING CIRCUIT CONTROL UNIT CONTROL UNIT FEEDBACK <MHV Output unit Block Diagram> BIAS-PWM BLADE REGULATION SWITCHING CONTROL UNIT TRANS CIRCUIT CONTROL UNIT SUPPLY FEEDBACK <BIAS Output Unit Block Diagram> Repair Manual 3-34 Samsung Electronics...
Page 156
CPU, the transfer voltage output will differ according to the preset transfer table. The changes in transfer output required by each load is controlled by PWM-DUTY. Repair Manual 3-37 Samsung Electronics...
Page 157
• LCD drive signals are sent from U1 P2-x pin group, P3-4~P3-6 pins. • Machine status LED drive signals are sent from U1 LED 1~ LED 8. RESONATOR 7.37 MHz UART2 16 X 2 Line MICOM Connector Reset Z8601 Key Matrix LEDs <OPE BLOCK DIAGRAM> Repair Manual 3-38 Samsung Electronics...
Base is regulated by On/Off switch and turns to DP dial signal with a COUPLER. • CTR 21 does not have telephone capability but has the number 3 and 4 Line Connection. No DP condition but possibility to get approval only on DTMF Dial based terminal. Repair Manual 3-39 Samsung Electronics...
Page 159
Must not ignite or overload protection 23) generate smoke shutdown withing generate smoke Refer to load short and when output shorted the range of when output shorted overload protection 23) for 5 sec. 3.5A~6.5A for 5 sec. Repair Manual 3-40 Samsung Electronics...
Page 160
3-8-4. FIXED TEMPERATURE CONTROL 3-8-4-1. Fixed Lamp Control Circui AC Power Live AC Neutral L501 R503 Zero crossing circuit Logic Unit Fuser On C502 THY501 R505 SMPS Unit R502 U501 CON502 DC Power <Fixed Lamp Control Circuit> Repair Manual 3-41 Samsung Electronics...
Page 161
When triac commutes off-line, the volt- age of both ends of triac will have the same voltage as the line voltage. Inductive I <Inductive Circuit> Repair Manual 3-42 Samsung Electronics...