Page 1
Owner’s Manual Tabletop Gas Grill 1-Burner Model VT280B1 FOR OUTDOOR USE ONLY THIS IS YOUR ASSEMBLY, CARE & USE MANUAL WITH IMPORTANT WARNING & SAFETY INFORMATION. PLEASE SAVE THESE INSTRUCTIONS. Manufactured by Outdoor Leisure Products, Inc. 5400 Doniphan Drive, Neosho MO 64850 CUSTOMER SERVICE: 1-866-475-5180 (Monday–Friday, 8:30 am–4:30 pm, CST)
WARNING THE PURPOSE OF THIS SAFETY ALERT SYMBOL IS TO ATTRACT YOUR ATTENTION TO POSSIBLE HAZARDS AS YOU ASSEMBLE AND USE YOUR GRILL. THIS INSTRUCTION MANUAL CONTAINS IMPORTANT INFORMATION NECESSARY FOR THE PROPER ASSEMBLY AND SAFE USE OF THE APPLIANCE. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS BEFORE ASSEMBLING AND USING THE APPLIANCE.
IMPORTANT SAFEGUARDS • Do not touch metal parts of grill until it has completely cooled (about 45 minutes) to avoid burns, unless you are wearing protective gear (BBQ mittens, pot holders, etc.) • Do not alter this grill in any manner. •...
Page 4
TOLL FREE 1-866-475-5180 (Monday–Friday, 8:30 am–4:30 pm, CST). NOTE : DO NOT RETURN UNIT TO THE STORE BEFORE CALLING THE TOLL FREE NUMBER. Do not dispose of your cartons until you are completely satisfied with your new Smoke Hollow grill.
Page 5
Pliers or Adjustable Wrench Item# Quantity Description Part NO. Item# Quantity Description Part NO. Rear Supporting Leg VT280RDS-18 Grill Lid and Firebox Assembly VT280B1-01 Side Supporting Leg VT280RDS-14 Warming Rack VT280RDS-04 TT250-09 Temperature Gauge VT280RDS-05 Igniter TT250-10 Grill Lid Handle VT280RDS-06...
Page 6
Grill Assembly Grill Assembly Fig. 1 Step 1: Attach (2) Side Supporting Legs to the Grill Lid and Firebox Assembly using (4) lock washers and (4) M6x12 screw. (Fig. 1) Step 2: Fig. 2 Attach the Rear Leg Support to the Grill Lid and Firebox Assembly using (2) lock washers and (2) M6x12.
Grill Assembly Grill Assembly Grill Assembly Grill Assembly Fig. 5A Step 5B Step 5: Attach the Grease Tray Handle to the Grease Tray using (2) M6x12 bolts. (Fig 5A) Slide the Grease Tray Assembly into the bottom of the Firebox. (Fig. 5B) Step 6: Attach (2) Heat Tent Supporting Brackets to the firebox using (4)
Grill Assembly Grill Assembly Grill Assembly Grill Assembly Fig. 8 Fig. 9 Step 8: Step 9: Remove hex nut from Igniter then Insert Igniter Insert the round end of Igniter Wire onto the Igniter into opening at the front of the Control box then then push other end of the wire into the pin end of tight Igniter to the Control panel with hex nut.
Grill Assembly Grill Assembly Grill Assembly Grill Assembly Fig. 12 Step 12: Insert (2) M5x17 shoulder bolts through wire loops on a Warming Rack then screw shoulder bolts to the Lid. Insert wire legs into holes on each sides of firebox.(Fig. 12 & 13) Fig.
Operating Instructions The installation of this appliance must be in accordance with all applicable local codes, or in the absence of local codes, either: National Fuel Gas Code ANSI Z223.1 NFPA 54 or Natural Gas and Propane Installation Code: CAN/CGA B149.1. To check your local codes, see your local LP gas dealer or Natural Gas Company.
Page 11
Operating Instructions WARNING: Read, understand and follow all warnings and instructions contained in this manual. DO NOT skip any of the warnings and instructions contained in the preceding sections of this manual. Follow the instructions exactly. 1. OPEN THE GRILL LID before attempting to light a burner so that fumes do not accumulate inside the grill. An explosion could occur if grill lid is down.
Page 12
Operating Instructions CONTROLLING FLARE-UPS AND GREASE FIRES: • Flare-ups are a part of cooking meats on a gas grill. This adds to the unique flavor of cooking on a gas grill. • Use caution when opening the lid as sudden fl are-ups may occur. Excessive flare-ups can over-cook your food and cause a dangerous situation for you and your grill.
Care and Maintenance CLEANING INTERIOR OF GRILL: • We recommend cleaning off food residue immediately after cooking by gently scrubbing grates with wire bristle brush and then turning burners to “HIGH” for approximately 5 minutes. WARNING: DO NOT leave grill unattended when grill is on. Wear oven mitts to protect from burns. •...
Page 14
Care and Maintenance BURNER ASSEMBLY / MAINTENANCE: • Although your burners are constructed of stainless steel, they may corrode as a result of the extreme heat and acids from cooking foods. Regularly inspect the burners for cracks, abnormal holes, and other signs of corrosion damage.
Trouble shooting Problem Possible Cause Prevention / Cure Burner will not light LP cylinder regulator knob is “off” Make sure regulator is securely attached to the LP cylinder, turn LP cylinder regulator to “Open” LP cylinder is low or empty Check if LP cylinder is empty.
Need help?
Do you have a question about the VT280B1 and is the answer not in the manual?
Questions and answers