Salus RT310 Installation Manual
Wireless programmable room thermostat
Hide thumbs
Also See for RT310:
- Quick manual (2 pages) ,
- Full user manual (20 pages) ,
- Quick start manual
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Salus RT310
Summary of Contents for Salus RT310
- Page 1 Model: RT310 Installation Manual...
-
Page 2: Table Of Contents
Introduction ........................4 Features ..........................5 Installation ......................... 5 Button functions and keys ..................7 Installer Mode ........................8 Operations ......................... 9 Other functions ......................11 Factory reset ........................12 Technical info ........................12 Warranty ..........................13 02 RT310 Installation Manual... -
Page 3: Product Compliance
Always isolate the AC Mains supply before installing or working on any components that require 230 VAC 50Hz supply. Box content The box includes the RT310 thermostat, 2 AA batteries a set of screws and the Quick Guide installation manual. RT310 thermostat 2X screws and plugs... -
Page 4: Introduction
Room thermostats need a free flow of air to sense the temperature, so they must not be covered by curtains or blocked by furniture. Nearby electric fires, televisions, wall or table lamps may prevent the thermostat from working properly. 04 RT310 Installation Manual... -
Page 5: Features
Connection details are shown below - no Earth connection is required for the correct and safe operation of the RT310, but a parking terminal is provided to connect an Earth wire if one is present. TERMINAL... - Page 6 Note: You can also use a flush mount housing and a German and UK wall box to mount the thermostat directly into the wall. The standard wall box has a diameter max 60mm and depth from 41-46 mm. The cable entry on the backplate must allow a cable with 5*1,5 mm 60mm 06 RT310 Installation Manual...
-
Page 7: Button Functions And Keys
Button functions and keys There are few user controls for the RT310, making this thermostat very easy to operate. These controls are shown below, along with a description of each of their functions. The temperature displayed on the LCD is the current room temperature. -
Page 8: Installer Mode
Function Parameter Description Default value Temperature display 0.1°C or Select the temperature display 0.5°C increments 0.5°C increments Temperature offset +/-3.0°C Calibrate your thermostat tempera- 0.0°C ture Frost setpoint temperature 5.0°C-17.0°C Set the Frost Point temperature 5.0°C 08 RT310 Installation Manual... -
Page 9: Operations
After that, all keys are unlocked and the thermostat is initialized. Then software version is shown. The typical reset display is shown below. The following table shows the settings of the RT310 digital thermostat after RESET button is pressed: Function... -
Page 10: Frost Protection
0.5°C steps per key press. The RT310 will return to Normal mode if no keys are pressed for more than 2 seconds. Once the new Setpoint is implemented, the change is permanently overridden until a new Setpoint is set again. Setpoint temperature cannot be changed if Frost Protection mode is enabled. -
Page 11: Other Functions
• The LCD display will be blank. • All output from the Control Unit will be turned off immediately. Press any key to wake up the RT310 and cancel SLEEP mode. Sleep Mode On Sleep Mode Off RESET 3 Sec... -
Page 12: Factory Reset
2xAA Alkaline batteries Switch Rating Switching Voltage: 0-230V Switching Current: 3A resistance 1A inductance Protection Rating: IP 30 Environment Operating Temperature/ 0°C ~ 50°C, 10% – 90% non-condensing Humidity: Storage Temperature/ -20°C~- 60°C, 10% – 90% non-condensing Humidity 12 RT310 Installation Manual... -
Page 13: Warranty
Warranty SALUS Controls warrants that this product will be free from any defect in materials or workmanship, and shall perform in accordance with its specification, for a period of two years from the date of installation. SALUS Controls sole liability for breach of this warranty will be (at its option) to repair or replace the defective product. - Page 14 SALUS Controls is a member of the Computime Group Maintaining a policy of continuous product development, SALUS Controls plc reserves the right to change specification, design and materials of products listed in this brochure without prior notice. For the latest PFD Instruction Manual, go to www.salus-manuals.com...
Need help?
Do you have a question about the RT310 and is the answer not in the manual?
Questions and answers
Changed batteries on RT310TX- going through pairing 5Y.9 it counts down ( red light flashing but green light does not come on
The green light will not come on during the pairing process of the Salus RT310 because the green light only flashes after the pairing process is successfully completed and tested. To test the connection, press the test pairing button once. If successfully paired, both the red and green lights on the receiver will flash. If the green light does not come on, it indicates that the pairing or testing process was not successfully completed.
This answer is automatically generated