Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Husqvarna TS 510 G
Summary of Contents for Husqvarna TS 510 G
-
Page 2: Table Of Contents
BEFORE YOU BEGIN: Read and understand all warnings and instructions before operating the Machine described in this manual. WARNINGS AND CAUTIONS IN THIS MANUAL MUST BE UNDERSTOOD AND FOLLOWED! FAILURE TO OBEY WARNINGS MAY RESULT IN SERIOUS INJURY OR DEATH. IT IS YOUR RESPONSIBILITY to make sure persons who use this machine have read this manual. -
Page 3: Symbol Definitions
Symbol Definitions Definicion De Los Simbolos • Please read the instructions for use prior to operating the machine for the first time. • Antes de la puesta en marcha, lea detenidamente las instrucciones y familiaricese con la máquina. • Mandatory •... - Page 4 • Water Supply On. • Suministro De Agua Conectado. • Water Supply Off • Suministro De Agua Desconectado • Water Supply • Suministro De Agua • Water Safety Switch-Press to Reset if Water Supply Interrupted • Si Se Ha Interrumpido El Suministro De Agua, Pulsar El Conmutador De Seguridad De Agua Para Reposicionarlo.
- Page 5 • Headlight • Luz De Cruce • Diamond Blade • Sierra Diamantada • Blade Diameter • Diámetro De La Hoja • Blade Engagement • Acoplamiento De La Hoja • Pulley Diameter • Diámetro De La Correa • Number of Revolutions Per Minute, Rotational Speed •...
-
Page 6: Dust Warning
• Engine Start • Arranque Del Motor • Repairs Are To Be Done By An Authorized Dealer Only • Las Reparaciones Deben Ser Efectuadas Únicamente Por Un Distribuidor Autorizado WARNING HEARING HAZARD DURING NORMAL USE OF THIS MACHINE, OPERATOR MAY BE EXPOSED TO A NOISE LEVEL EQUAL OR SUPERIOR TO 85 dB (A) ATENCION RIESGO DE DAÑO AUDITIVO... -
Page 7: Decal Descriptions And Locations
DECAL DESCRIPTIONS AND LOCATIONS DESCRIPCIÓN DE CALCAMONIAS Y UBICACIONES DEPTH STOP ADJUSTMENT LIFTING EYE Read manual. LIFT 20” 14” Lea el manual. HERE Read manual. Veuillez lire le manuel. Lea el manual. WARNING Veuillez lire le manuel. Only Use Lifting Sling Approved For Overhead Lifting. -
Page 8: Warnings
SAFETY WARNINGS FOR OPERATION OF THIS MACHINE WARNING! FAILURE TO COMPLY WITH THESE WARNINGS AND OPERATING INSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS BODILY INJURY! WARNING! DO’s and DO NOT’s Read this entire operator’s manual before operating this machine. Understand all warnings, instructions, and controls. keep all guards in place and in good condition. - Page 9 If you have any questions relative to its application, DO NOT use the machine until you have written to us and we have advised you. Husqvarna Construction Products 17400 West 119th Street...
-
Page 10: Saw Dimensions
Guardmatic Dimensions... -
Page 11: Specifications & Power Source
Specifications MODEL 9 HP 9 HP w/ Clutch 13 HP 13 HP w/ Clutch TYPE Gasoline Engine Gasoline Engine Gasoline Engine Gasoline Engine Blade Guard 14 - 0" 14 - 0" 14 - 0" 14 - 0" Capacity (350 - 500 mm) (350 - 500 mm) (350 - 500 mm) (350 - 500 mm) -
Page 12: Parts Identification & Diagram
Parts Identification:... -
Page 13: Features
•Mandatory Any persons not involved in the work, •Prohibition •Obligatorio should leave the area. •Prohibición •Warning Triangle •Indication •Triángwulo De WARNING! •Indicación Advertenciao Use only blades marked with a maximum operat- ing speed greater than the blade shaft speed. These signs will give advice for your safety. 2. -
Page 14: Check Before Operating
3. Check Before Operating blades are to be used, the depth stop must be set for 14” (350mm) blades. The depth stop will not function properly for 18” (450mm) blades because Take into account the working condi- the blade will cut into the Conveyor Cart Assembly if tions from a health and safety point of the operator does not take care. -
Page 15: Fitting The Blade
WARNING! Only use Lifting Sling approved for overhead lift- ing. Using Improper Lifting Sling can result in inju- ry or death of operator or persons in work area! 4. Fitting The Blade • The blade rotates in a “down-cut” direction. This means that the front of the blade is moving downward while the rear of the blade is moving upward. - Page 16 CAUTION! DO NOT run the WATER PUMP (4) for extended periods of time without water! The WATER PUMP (4) could be damaged! • Hint: To reduce vibration of the saw, the water reservoir pan [of the Frame Assemble (1)] can be filled with sand.
- Page 17 . Hand Controlled Cutting Method: START (ON) STOP Start the engine by using the procedure in the engine operation manual. Make sure that the Stop Switch (19) is in the “START” (On) Position before using the engine starting rope. Open the engine throttle full open.
-
Page 18: Incidents During Operation
Stop the unit by putting the Stop Switch (19) into • Check engine oil daily. Change engine oil after the “Stop” (Off) position. Wait for all blade move- every 50 hours of operation. Engine Oil capacity ment to stop before removing material from the is shown below. - Page 19 When Required: • Note: Before starting to align the head platform make sure the blade is flat and is NOT bent or • “Sta-Level” Blade Guard: If the blade guard damaged! becomes loose and pivots too freely the blade guard rotation can be tightened. Adjust the Top •...
-
Page 20: Belt Tension
Assembly () downward, the Springs (40) should be loosened so that they become shorter in length. To do this, turn each of the Drawbolts (41) Counter- Clockwise until the desired pivot force is achieved. Cutting Head Assembley Does Not Raise Properly: If the Cutting Head will not pivot to the maximum upper position, then the Springs (40) need to be tightened so that they become longer... -
Page 21: Important Advice
Tensioning Blade Shaft V-Belts: • Blade flanges must be full diameter - minimum of 4” (101,6 mm). Replace worn flanges at once because undersized flanges shorten blade life and cause blade breakage. • Check the conveyor cart condition on a regular basis.