Cut Chart - 55A Standard Consumables - Hypertherm powermax900 Operator's Manual

O
PERATION

CUT CHART - 55A STANDARD CONSUMABLES

The following recommended settings are for mechanized cutting at 55 amps. Torch-to-work distance
for the following cut charts is 1/16 inch (1.6 mm) for all cuts.
Shield
120602
M a e t i r l a T h c i k
g ( . a r o n i ) . (
1 6 g . a
1 0 g . a
/ 1 " 4
/ 3 " 8
1 1 / " 6
/ 1 " 8
/ 1 " 4
/ 3 " 8
1 1 / " 6
/ 1 " 8
/ 1 " 4
/ 3 " 8
* Recommended travel speeds are 10–20% slower than maximum. These slower speeds will produce optimum
cut quality.
The voltage between the tip of the torch and the workpiece will exceed 113VDC if shielded
consumable parts are not installed in the torch. If using the 400V CE power supply, the hand
torch must be operated with shielded parts to maintain the S mark and CE low-voltage
compliance for hand held applications. See Section 5: Consumable Parts - For CE
Compliance for a list of CE consumable parts. This requirement does not apply to machine
torch applications.
4-12
Retaining Cap Nozzle
120600 120577
n e s s
M a e t i r l a
m m )
1 5 . M d l i S e t l e
3 4 . M d l i S e t l e
6 4 . M d l i S e t l e
9 5 . M d l i S e t l e
1 6 . S a t n i e l s s S e t l e
3 2 . S a t n i e l s s S e t l e
6 4 . S a t n i e l s s S e t l e
9 5 . S a t n i e l s s S e t l e
1 6 . A u l m n i u m
3 2 . A u l m n i u m
6 4 . A u l m n i u m
9 5 . A u l m n i u m
WARNING
Electrode
120573
A c r A c r
C C C C C r u r u r u r u r u e r e r e r e r e r t n t n t n t n t n V V V V V l o l o l o l o l o a t a t a t a t a t g g g g g e e e e e
( ) ( ) ( ) ( ( ) A A A A A ) ( ) V ( ) V ( ( ) V ( ) V ) V ( p i
5 5 1 1 6 3
5 5 1 1 9 1
5 5 1 2 0
5 5 1 2 5 3
5 5 1 1 7 3
5 5 1 1 8 1
5 5 1 2 1 5
5 5 1 2 5 2
5 5 1 1 7 5
5 5 1 1 9 2
5 5 1 2 5 1
5 5 1 2 9 5
PAC125
Swirl Ring
Torch
120576
R e c o m m e n d e d P e i c r
T T T T T a r a r a r a r a r v v v v v l e l e l e l e l e S S S S S p p p p p e e e e e e e e e e * d * d * d * d * d D D D D D e e e e e a l a l a l a l a l
m ) ( m m / m i ) n ( ) S ( ) S ( ) S ( ) S ( ) S
3 0 8 3 8 0 n a /
6 0 4 0 6 0 0 5 .
7 5 1 9 0 0 1 0 .
5 8 9 0 2 0 .
1 5 8 0 0 0 n a /
4 0 3 5 6 0 0 5 .
5 1 4 0 0 1 0 .
8 7 1 0 2 0 .
5 0 1 3 9 7 0 n a /
8 0 7 1 1 0 0 5 .
3 5 3 4 3 0 1 0 .
5 1 4 0 0 2 0 .
Operator Manual
e
y y y y y