Related Manuals for Workzone WB 20
Summary of Contents for Workzone WB 20
- Page 1 WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 1 User Manual Spend a little Live a lot. 20 V LITHIUM-ION CORDLESS HAMMER DRILL WB 20 ORIGINAL INSTRUCTIONS...
-
Page 2: Overview
WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 2 Fig. 1... - Page 3 WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 3 Fig. 2 Fig. 3 Fig. 4 Rechargeable battery is Rechargeable battery is Rechargeable battery is fully charged partially discharged empty and must be charged...
-
Page 4: Use
WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 4 Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 Fig. 11... -
Page 5: Pack Contents/Device Parts
WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 5 Parts description Quick-action safety chuck Torque adjustment ring Mode selection ring (screwing/drilling/hammer drilling) Gear switch Charge level display Right-handed/left-handed rotation selector Thread for belt-clip Rechargeable battery Rechargeable battery release button Battery receptacle On/Off switch (with speed control) LED work light Additional rechargeable battery Magnetic bitholder... -
Page 6: Table Of Contents
WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 6 Overview Pack contents/device parts General information Reading and storing the user manual Explanation of symbols Safety Proper use Residual risks General power tool safety instructions Cordless tool use and care Special safety instructions for hammer drills Additional safety instructions for chargers Supplementary safety instructions Preparation... -
Page 7: General Information
It contains important information on start-up and handling. For improved readability, the 20 V lithium-ion cordless hammer drill WB 20 will be referred to only as the “cordless hammer drill” below. Before using the cordless hammer drill, read the user manual carefully. - Page 8 WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 8 General information NOTICE! This signal word warns against potential damage to property. Declaration of conformity (see chapter “Declaration of conformity”): Products marked with this symbol meet all applicable Community regulations for the European Economic Area. Do not expose the rechargeable battery to temperatures above 50 °C Avoid contact between the rechargeable battery and water!
-
Page 9: Safety
WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 9 Safety Safety Proper use The cordless hammer drill is only suitable for drilling and driving screws into wood, plastic, masonry and metal. The cordless hammer drill is not designed to be used commercially, in trades or for industrial applications; it is only designed for private users and DIY projects. - Page 10 WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 10 Safety • Injury to health attributed to vibration emissions if the device is used over a prolonged period of time or is not guided and maintained properly, • Injury and damage to property caused by projected parts or tool adapters that break during use, •...
-
Page 11: General Power Tool Safety Instructions
WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 11 Safety In addition to the safety guidelines in this user manual, please be absolutely sure to observe the regulations for operating the cordless hammer drill that are in force in your country. In addition to the safety instructions in this user manual and the special regulations for your country, the generally recognised technical rules for operating this cordless hammer drill must be observed. -
Page 12: Personal Safety
WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 12 Safety b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. -
Page 13: Power Tool Use And Care
WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 13 Safety e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. -
Page 14: Cordless Tool Use And Care
WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 14 Safety g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working con- ditions and the work to be performed. Use of the power tool for could result in a operations different from those intended hazardous situation. -
Page 15: Additional Safety Instructions For Chargers
WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 15 Safety c) Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live"... - Page 16 WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 16 Safety a) Before using the charger, read through all instructions and all precautionary measures for the charger and rechargeable battery. You can find notes in these instructions and on the device itself amongst others. b) Check the charger regularly for damage, particularly the connector cable and housing.
- Page 17 WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 17 Safety Do not attempt to charge the rechargeable battery with a charger other than the enclosed one. The charger shipped with this power tool and the rechargeable battery pack must be used together. m) Only use the charger to charge the rechargeable battery. The charger must not be used as a power supply for the power tool.
-
Page 18: Supplementary Safety Instructions
WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 18 Safety Supplementary safety instructions Risk of electric shock! A faulty electrical installation or excessive mains voltage may result in an electric shock. − Only connect the charger if the mains voltage of the socket corresponds to the nameplate specification. −... - Page 19 WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 19 Safety Risk of injury! This cordless hammer drill is not intended to be used by persons with impaired physical, sensory or mental abilities or who lack experience and/or knowledge unless they are supervised by a person responsible for their safety or are instructed by such a person on how to use the device.
-
Page 20: Preparation
WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 20 Preparation − If necessary, clean the contacts of the rechargeable battery and device before inserting them, e.g. with a piece of emery cloth. − Do not use aggressive solvents to clean the cordless hammer drill. −... -
Page 21: Charging The Rechargeable Battery
WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 21 Preparation Remove the packaging material and all protective foils. 2. Check to make sure that the delivery is complete (see fig. 1). 3. Take the cordless hammer drill out of the storage case (19) and check whether the cordless hammer drill or the individual parts exhibit damage. -
Page 22: Operation
WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 22 Operation The rechargeable battery is only precharged to a low level. Therefore, charge the rechargeable battery before first use. Insert the mains plug of the charger (18) in the socket. 2. Push the rechargeable battery release button (9) and pull the rechargeable battery (8) out of the rechargeable battery holder. - Page 23 WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 23 Operation − Do not touch the drill bit until it has cooled down. − Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
-
Page 24: Utilising Tools
WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 24 Operation Utilising tools (fig. 7) Twist counterclockwise to open the quick action safety chuck. 2. Insert a suitable drill or bit into the cavity of the chuck. 3. Tighten the quick-action safety chuck by turning clockwise. The quick-action safety chuck is equipped with a lock. - Page 25 WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 25 Operation 5. Use the gear switch (4) to select 1st or 2nd gear. Do not push the On/Off switch (11) and the gear switch simultaneously to avoid damaging the cordless hammer drill. Speed 1: 0 to 400 rpm Speed 2: 0 to 1550 rpm Speed 1 is suitable for screwing and drilling a large bore diameter.
- Page 26 WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 26 Operation Drilling (metal) • Centre punch the marking for the drill hole with a centre punch. • Clamp in the work piece and place a wooden block under it to prevent deformation. • Use an HSS spiral drill bit. •...
-
Page 27: Clearing A Jam
WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 27 After use Releasing a jammed bit If the cordless hammer drill jams, release the on/off switch (11) and retrieve the drill from the hole. 2. Check whether the jam is caused by the cordless hammer drill by briefly pressing the on/off switch. -
Page 28: Cleaning
WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 28 Cleaning Cleaning NOTICE! Risk of damage! Using unsuitable cleaners could damage the cordless hammer drill and accessories. − Do not use any aggressive cleaners, brushes with metal or nylon bristles, sharp or metallic cleaning utensils such as knives, hard scrapers and the like. -
Page 29: Storage And Transport
WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 29 Storage and transport 5. Clean the contacts of the rechargeable battery and the cordless hammer drill with a dry, clean cloth. 6. Then dry the cordless hammer drill thoroughly and let it dry completely for a while. Do not lubricate the cordless hammer drill. -
Page 30: Repairs
WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 30 Troubleshooting Make sure that the cordless hammer drill and the accessories are completely dry. 2. Fold up the mains cord so that it does not knot or kink. 3. Always place all accessories and especially the drill bits (16) and the bits (15) back in the storage case (19) to prevent the loss of accessory parts. - Page 31 WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 31 Troubleshooting Problem Possible cause Solution The cordless hammer The rechargeable Recharge the drill cannot be started. battery does not rechargeable battery (8) have enough power. (see chapter “Charging the rechargeable battery”). The rechargeable Push the rechargeable battery has not been battery all the way into inserted properly.
-
Page 32: Technical Data
WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 32 Technical data Technical data Cordless hammer drill Model: WB 20 / 5451513/5451514 Article number: 74855 Idle speed: 1. gear: 0 to 400 rpm 2. gear: 0 to 1550 rpm Impact rate: 1. gear 0 to 6.000 bpm 2. -
Page 33: Noise And Vibration Information
WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 33 Noise and vibration information Noise and vibration information The specified noise and vibration levels were determined in accordance with the standards EN 60745-1, EN 60745-2-1 and EN 60745-2-2. The specified vibration emission level was measured on the basis of a standardised test procedure and can be used to compare power tools with one another. -
Page 34: Disposal
WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 34 Disposal CAUTION! Hearing loss! Exposure to noise may result in loss of hearing. − Only work with suitable ear protection. − Persons nearby must also wear suitable ear protection. CAUTION! Noise disturbance! This device causes a certain unavoidable noise disturbance. −... - Page 35 WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 35 Disposal − Make defective parts available to the special waste collection service. − Consult a specialist store or your local government! Old devices must not be disposed of with household waste! This symbol indicates that this product must not be disposed of together with domestic waste in compliance with the Directive (2012/19/EU) pertaining to waste electrical and electronic equipment (WEEE).
-
Page 36: Ec-Declaration Of Conformity
20 V Li-Ion We declare with sole responsibility, that Cordless hammer drill the product listed below ... + Charger Cordless hammer drill WB 20 + Charger TF0702082000B WORKZONE Nr. 5451513/5451514 · 74855 · 02/2017 ... meets all of the requirements of the 2006/42/EG (MRL) listed directives. - Page 37 WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 37...
- Page 38 WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 38...
- Page 39 WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 39...
- Page 40 WZ-5451513-Bedien-1611_(24) 22.11.16 15:24 Seite 40 Spend a little Live a lot. Great care has gone into the manufacture of this product and it should therefore provide you with years of good service when used properly. In the event of product failure within its intended use over the course of the first 3 years after date of purchase, we will remedy the problem as quickly as possible once it has been brought to our attention.
Need help?
Do you have a question about the WB 20 and is the answer not in the manual?
Questions and answers
Where can I find a replacement battery?