Related Manuals for Blade 300 CFX BNF Basic
Summary of Contents for Blade 300 CFX BNF Basic
- Page 1 Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni ® ® ®...
- Page 2 NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product. Meaning of Special Language The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product: NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.
-
Page 3: Table Of Contents
Table of Contents Low Voltage Cutoff (LVC) ................. 4 AR7200BX Default Blade 300 CFX Setup ............9 Transmitter Setup ................... 4 AR7200BX Parameter Menu Tips ..............9 Transmitter and Receiver Binding ..............5 AR7200BX Fine-tuning and Adjustment ............10 Throttle Hold ....................5 Blade 300 CFX Troubleshooting Guide ............ -
Page 4: Low Voltage Cutoff (Lvc)
Low Voltage Cutoff (LVC) Once the battery reaches 9V under load, the ESC will continuously lower power Repeatedly fl ying the helicopter until LVC activates will damage the helicopter supplied to the motor until complete shutdown occurs. This helps prevent battery. -
Page 5: Transmitter And Receiver Binding
Transmitter and Receiver Binding Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifi er) code of a single specifi c transmitter. You need to ‘bind’ your chosen Spektrum™ DSM2/DSMX technology equipped aircraft transmitter to the receiver for proper operation. Binding Procedure Program your transmitter using the Transmitter Setup found in this manual. -
Page 6: Control Tests
Control Tests CAUTION: You must complete the Rudder and Cyclic tests prior to fl ight. Failure to complete the tests and ensure the sensor directions are not reversed can cause the helicopter to crash, resulting in property damage and injury. Rudder 1. -
Page 7: Flying The Blade 300 Cfx
First fl ights should be performed in normal mode and low cyclic and rudder to fl y your aircraft. dual rates until you are familiar with the fl ying manner of the Blade 300 CFX. Discover the rates that fi t your fl ying style. -
Page 8: Blade Helicopter Belt Tension
Blade Helicopter Belt Tension Belt tension that is too tight results in loss of power and causes the belt to wear more quickly. Tension that is too loose can cause belt damage and loss of tail rotor control in fl ight. -
Page 9: Ar7200Bx Default Blade 300 Cfx Setup
G. If you update the fi rmware on the AR7200BX to non-Blade 300 CFX fi rmware, all Blade 300 CFX helicopter default settings will be deleted. You will need to complete the entire AR7200BX setup process before fl... -
Page 10: Ar7200Bx Fine-Tuning And Adjustment
Increase the rudder gain in your transmitter The helicopter tail does not stop precisely Adjust the rudder heading lock gain parameter in the AR7200BX Make sure the tail drive belt tension is adjusted correctly Blade 300 CFX Troubleshooting Guide Problem Possible Cause Solution Low fl... -
Page 11: Limited Warranty
Limited Warranty What this Warranty Covers assistance. For questions or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll free Horizon Hobby, Inc., (Horizon) warrants to the original purchaser that the product telephone number referenced in the Warranty and Service Contact Information purchased (the “Product”) will be free from defects in materials and workmanship section to speak with a Product Support representative. -
Page 12: Warranty And Service Contact Information
Instructions for disposal of WEEE by users in No. HH2014022803 the European Union Product(s): 300 CFX BNF Basic This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by Item Number(s):... -
Page 13: Exploded Views
Exploded View / Explosionszeichnung / Vue éclatée / Vista esplosa... -
Page 16: Replacement Parts
300 CFX - Paliers Blocchi cuscinetti: 300 CFX 3 BLH4603 Bottom Plate Mount: 300 CFX Blade 300 CFX: Halter Lagerplatte unten 300 CFX - Fixations de train Supporto piastra inferiore: 300 CFX 300 CFX - Fixations de poutre de 4 BLH4604... -
Page 17: Optional Parts
300 CFX -Coulisseau d’anticouple Set cursore passo coda: 300 CFX Set: 300 CFX 300 CFX -Paire de pales 42 BLH4537 Tail Rotor Blade Set: 300 CFX Heckrotorblätter: 300 CFX Set pale coda: 300 CFX d’anticouple Tail Rotor Blade Grip/Holder Set:... - Page 18 Set cursore passo coda alluminio: BLH4536A Slider Set: 300 CFX 300X aluminium 300 CFX Tail Rotor Blade Set, Orange: 300 BLH4537OR Heckrotorblätter Set Orange: 300X 300X -Pales d’anticouple, orange Set pale coda, arancio: 300 CFX Tail Rotor Blade Set, Green: 300 BLH4537GR Heckrotorblätter Set Grün: 300X...
- Page 19 ©2015 Horizon Hobby, LLC. Blade, DSM, DSM2, DSMX, Dynamite, Prophet, E-fl ite, Celectra, the BNF logo, ModelMatch, AirWare and EC3 are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc.
Need help?
Do you have a question about the 300 CFX BNF Basic and is the answer not in the manual?
Questions and answers