Table of Contents
Related Manuals for ALLEN & HEATH XONE:22
Summary of Contents for ALLEN & HEATH XONE:22
- Page 1 ALLEN&HEATH SERVICE MANUAL XONE:22 Copyright © 2009 Allen & Heath Limited. All rights reserved Allen & Heath Limited Kernick Industrial Estate, Penryn, Cornwall, TR10 9LU, UK http://www.allen-heath.com ALLEN&HEATH Xone:22 service manual AP7528_3 Page - 1 - of 12...
-
Page 2: Limited One Year Warranty
In certain territories the terms may vary. Check with your ALLEN & HEATH agent for any additional warranty which may apply. For further assistance please contact our distributor or your territory. http://www.allen-heath.com/UK/distributors.asp Release notes for this issue ALLEN&HEATH Xone:22 service manual AP7528_3 Page - 2 - of 12... -
Page 3: Software And Firmware
SERVICING PRECAUTIONS AND GENERAL NOTES ACCESS CHANGE PHONO INPUT TO LINE INPUT PARTS IDENTIFICATION • How to order parts • Exterior parts • Interior parts SOFTWARE & FIRMWARE SPECIFICATION ALLEN&HEATH Xone:22 service manual AP7528_3 Page - 3 - of 12... - Page 4 They are not critical to the basic function of the unit. It is for the owner / service engineer to decide to update a unit with development changes. ALLEN&HEATH Xone:22 service manual AP7528_3 Page - 4 - of 12...
- Page 5 Ensure that jumper settings and control configurations are correctly set according to the requirements of the customer. Continued - ALLEN&HEATH Xone:22 service manual AP7528_3 Page - 5 - of 12...
-
Page 6: Operation
Fault finding: For effective fault diagnosis trace the signal flow through the circuit path. Refer to the system block diagram. Replacement circuit assemblies are available from Allen & Heath. ALLEN&HEATH Xone:22 service manual AP7528_3 Page - 6 - of 12... - Page 7 5. Take great care to ensure that no harnesses become trapped and that all connectors are fully pushed home. Replace the screws and test the mixer for correct operation. REMOVE THE SCREWS ARROWED ALLEN&HEATH Xone:22 service manual AP7528_3 Page - 7 - of 12...
- Page 8 It is a good idea to leave the jumper links attached to one pin so that they can be refitted at a future date. Remove these two j u mper links (JP1 and JP2) for each channel that you want to convert to line. ALLEN&HEATH Xone:22 service manual AP7528_3 Page - 8 - of 12...
-
Page 9: Parts Identification
EXTERIOR PARTS AJ7304 AI8007 AJ7304 AI8007 AJ7305 AJ7305 AI8006 AI8006 AJ7304 AI8007 AJ7464 Channel fader 003-897 Square red AJ7305 AI8006 AJ5320 Crossl fader 003-876 ALLEN&HEATH Xone:22 service manual AP7528_3 Page - 9 - of 12... - Page 10 AL4396 RCA phono AL4977 Ground Pillar AL8106 Mix out XLR RCA phono Al2411 Headphone AL3753 Small jack AL5323 Mic XLR AL2414 Headphone AJ4346 AJ4346 Large jack AL0328 AI8004 AI8007 ALLEN&HEATH Xone:22 service manual AP7528_3 Page - 10 - of 12...
-
Page 11: Interior Parts
INTERIOR PARTS Input 003-873 Master 003-874 Mic is break off Connector 003-875 ALLEN&HEATH Xone:22 service manual AP7528_3 Page - 11 - of 12... -
Page 12: Specification
Noise 22-22Khz Main Mix out unity -84dBu un-weighted Fader shut off Channel fader >-74dB Xfade shut off Xfader >-80dB Frequency 10Hz to 30kHz +0/-3dB Response Weight 2.2kg (5.5lb) Weight Packed 3.5kg (8.0lb) ALLEN&HEATH Xone:22 service manual AP7528_3 Page - 12 - of 12...
Need help?
Do you have a question about the XONE:22 and is the answer not in the manual?
Questions and answers