Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Stack st8130 series
Summary of Contents for Stack st8130 series
- Page 1 ST8130 Series Road Car Display Systems Users Guide...
- Page 3 Preface Congratulations Registration Form...
- Page 4 Purpose of this manual...
-
Page 5: Edition Notice
Edition Notice Parameter Type UK Version US Version EU Version Speed MPH or km/h MPH or km/h* km/h or MPH* Distance Miles or km* Miles or km* Km or Miles* Temperature ºC ºF ºC Wheel Circumference Millimetres Inches Millimetres Fuel level Litres Gallons (US) Litres... -
Page 6: Related Products From Stack Limited
Related Products From Stack Limited • • • • • • • • • • • ©... -
Page 8: Who To Contact At Stack In Case Of Difficulty
Who to Contact at Stack in Case of Difficulty... -
Page 9: Table Of Contents
Contents Preface Related Products From Stack Limited Who to Contact at Stack in Case of Difficulty Contents Chapter 1. Introducing the Display Systems ST8130 Models How to use this Manual Chapter 2. Getting Started The Display Module Wiring Harness Connecting the Components Chapter 3. - Page 10 Temperature sensors Wheel speed sensor (ST670-Option) Pulse Amplifier Interface (ST492-Option) Fuel Tank Sender Lap timing sensor (Optional, Std on ST8130M) Trackside Infra-Red Lap Beacon (Optional, Std on ST8130M) Air Temperature Sensor (optional on ST8130 variant) Wiring harness Checks and Alarms Chapter 6.
-
Page 11: Chapter 1. Introducing The Display Systems
Chapter 1. Introducing the Display Systems... -
Page 12: St8130 Models
• • ST8130 Models... -
Page 13: How To Use This Manual
How to use this Manual System Overview... -
Page 14: Chapter 2. Getting Started
Chapter 2. Getting Started Standard ST8130 Road Car Display System Items Quantity Description Display Module (ST867 ) with 2 mounting brackets Wiring Harness (ST872 ) Fuel level Extender (ST918037) Oil Pressure Sensor (ST747-M10 (EU) or ST747-1/8 NPTF (UK/USA)) Oil & Water Temperature Sensors (ST762 (EU) ST764 (UK/USA)) Switches (supplied with and to be connected to the wiring harness) Speed Sensor (ST670) or Pulse Amplifier (ST492) ST8130P variant only (As above plus the following parts) -
Page 15: The Display Module
Optional ST8130 Road Car Display System Items Quantity Description Air Temperature Sensor (ST765) Quantity Description Infra-red Lap Beacon (ST544) Lap Timing Receiver (ST543) The Display Module... -
Page 16: Wiring Harness
Wiring Harness Labels on Short Cables Connection To S1 to S4 Switches 1 to 4 Wheel speed input (ST492 or ST670) Gear shift warning light Alarm warning light Data logging expansion pack Optional in-car lap timing sensor (Std on ST8130M) Labels on Long Cables Connection To Air temperature sensor (optional on ST8130 variant) -
Page 17: Connecting The Components
Connecting the Components... -
Page 18: Chapter 3. Operating The Display System
Chapter 3. Operating the Display System Switching the Display System on Changing the display layers... - Page 19 Display Layer 1 • • • • Display Layer 2 (ST8130 & P variant) Oil T MPH Oil P 110 C 135 • • •...
- Page 20 Display Layer 2 (ST8130M variant) Water MPH Oil P 75 C • • • Display Layer 3 (ST8130 & P variant) Water MPH Oil P 75 C 135 • • • Display Layer 3 (ST8130M variant) Oil T 12.6V Fuel P 110 C 135 •...
- Page 21 •...
- Page 22 Display Layer 4 (ST8130 variant) Air T MPH Batt 5 C 135 12.6V • • • Display Layer 4 (ST8130P variant) Fuel P MPH Batt 12.6V • • • Display Layer 4 (ST8130M variant) Lap 12 MPH Best 1:35.10 135 1:35.06 •...
- Page 23 • Display Layer 5 Lap 12 MPH Best 1:35.10 135 1:35.06 • • • • Display Layer 5 (ST8130M variant) >< 1:19:88 135 00.00 • • • •...
-
Page 24: Peak Values (Tell Tales)
Peak Values (Tell Tales) Parameter Type of Peak Gated to RPM Value Engine Speed (RPM) Maximum Wheel Speed Maximum Oil Pressure Minimum Oil Temperature Maximum Water Temperature Maximum Fuel Level Value at Reset Battery Voltage Minimum Air Temperature / Ice Warning Minimum (ST8130 variant) Fuel Pressure (ST813P/M) - Page 25 Displaying the Peak Values Resetting the Peak Values • • •...
-
Page 26: Alarms
Parameter New Peak Value Engine RPM Current value Wheel speed Current value Oil Pressure 999 PSI or 99.9 Bar Oil Temperature 0C or 0F Water Temperature 0C or 0F Fuel Level Current value Battery Voltage Current value Air Temperature (ST8130 variant) Current value Fuel Pressure High range sensor 999 PSI or 99.9 Bar... - Page 27 Parameter Alarm is triggered Gated to RPM when the: Oil Pressure Current value drops below the preset value Oil Temperature Current value exceeds the preset value Water Temperature Current value exceeds the preset value Fuel Level (warning light only) Current value drops below the preset value Battery Voltage Current value drops...
- Page 28 Displaying an Alarm Clearing an Alarm Showing the Last Alarm Low Oil P -0.0 psi 55 L 130 004014...
-
Page 29: Lap Times
Lap times Lap 12 MPH Best 1:35.10 135 1:35.06 Resetting the Lap Time to Zero Lap 0 MPH Best 0:00.00 0 0:00.00 Gear shift light... -
Page 30: Chapter 4. Configuring The Display System
Chapter 4. Configuring the Display System Configuration mode Setting or resetting configuration values... - Page 31 Switching Alarms on or off...
- Page 32 Configurable Parameters Configurable Setting Required Switchable Parameter Parameter Shift RPM RPM at or above which the gear shift light is to come on Low Fuel Volume of fuel in tank at or below which the low fuel warning light is to be turned on. Ice Warning Air temperature at or below which the Ice (ST8130 variant)
- Page 33 Shift RPM: EDIT TEST Shift RPM 7000 on Low Fuel: EDIT TEST Low Fuel 10 L on Air Temperature (ST8130 variant): EDIT TEST Ice Warning- 7C on High Oil Temperature: EDIT TEST High Oil T 130C on High Water Temperature: EDIT TEST High Water 105C on Low Battery Voltage:...
- Page 34 Low Fuel Pressure (ST8130P/M variant): EDIT TEST Low Fuel P 35 on Low Oil Pressure: EDIT TEST Low Oil P 35 on Fuel Level Calibration: Sw1 & 2 to calibrate Fuel Tank Sender Gate RPM: EDIT TEST Gate RPM 3000 on Engine speed cylinders: E.S.
-
Page 35: Wheel Pulses And Circumferences
Wheel circumference: Wheel Cir 1000 mm Wheel Pulses and Circumferences Calculations for the ST8130 (ST492 Pulse Amplifier) ÷ ÷... - Page 36 ÷ ÷ ÷...
- Page 37 Calculations for the ST8130 (ST670 Wheel Sensor) ÷...
- Page 38 ÷ ÷ ÷ ÷...
-
Page 39: Configuring The Fuel Pressure Sensor (St8130P/M Variant)
Configuring the Fuel Pressure Sensor (ST8130P/M variant) -
Page 40: Calibrating The Fuel Level
Calibrating the Fuel Level... - Page 41 Tank Qty 0L Reading 255...
- Page 43 Start fuel tank calibration process: Press Switches 1 and 2. Switch 1 and 2 Set initial Tank Qty value using Switch 1 to decrease value or Switch 2 to increase value. Then press Switch 3 to confirm or Switch 4 Switch 4 to cancel and leave the original calibration set.
-
Page 45: Chapter 5. Installing The Display System
Chapter 5. Installing the Display System Who can install the Display System? Tools needed to install the Display System ST8130 with ST670 Option ST8130 with ST492 Option Preconfigured Display Systems Custom Configured Display Systems... -
Page 46: Fitting The Display Module
Fitting the Display Module 97mm (3.82 in.) 42.5mm (1.67 in) Rad. Typ. 5.5mm (0.22 in) Rad. Typ. 54.5mm 37.5mm (2.15 in.) (1.48 in.) 95mm (3.74 in.) 89.5mm (3.52 in.) 5.5mm (0.22 in.) 190mm (7.48 in.) Positioning the Display Module... -
Page 47: Switches
Switches Switch Functions Switch 1 Show the peak values. Switch 2 Clear an alarm or show the last alarm. Switch 3 Change the display layer or clear an alarm. Switch 4 Reset the trip distance to zero and start the lap timer. The trip distance is reset after each lap. -
Page 48: Warning Lights
Warning lights Engine Speed (RPM) Measurement... -
Page 49: Connecting The Display System To The Ignition System
Connecting the Display System to the Ignition System Ignition System Normally Fitted To Connection Point Bosch Citroen AX 'Sport' and Tachometer output (coil negative) 'GT' with 100K series resistor Bosch 3-pin CD Porsche 911 Carrera Pin 'C' (points connection) Bosch 8-pin CD Porsche 930 Turbo '76 Pin 7 on ignition unit General Motors... - Page 50 Standard contact breaker system Series Resistor Connection Electronic Ignition or ECU Connection...
-
Page 51: Pressure Sensors
Pressure sensors Fitting the pressure sensors Country Code Sensor type Max Pressure Thread Size ST747-M10* 10 bar/145 psi M10 x 1 US/ UK ST747- 1/8 NPTF 10 bar/145 psi NPTF OPTION ST747- 1/8 10 bar/145 psi BSPT... - Page 52 Installing the pressure sensors • • • •...
-
Page 53: Temperature Sensors
Temperature sensors Fitting the temperature sensors •... -
Page 54: Wheel Speed Sensor (St670-Option)
Wheel speed sensor (ST670-Option) Fitting the wheel speed sensor • • • • • • ± ± • •... -
Page 55: Pulse Amplifier Interface (St492-Option)
Pulse Amplifier Interface (ST492-Option) Introduction Installation Mechanical Using the 'dual-lock' fastener with Stack sensors... - Page 57 Electrical The amplifier connects into the ST8130 system via a four way Mini Sure Seal (MSS) socket, the larger of the two connectors on the amplifier. Use the extender cable with an MSS connector at each end to connect the amplifier to the WS input on the harness.
-
Page 58: Fuel Tank Sender
ST492 Technical Specification Fuel Tank Sender Single-Wire Sender Two-Wire Sender... -
Page 59: Lap Timing Sensor (Optional, Std On St8130M)
Lap timing sensor (Optional, Std on ST8130M) -
Page 60: Trackside Infra-Red Lap Beacon (Optional, Std On St8130M)
Trackside Infra-Red Lap Beacon (Optional, Std on ST8130M) • • • •... -
Page 61: Air Temperature Sensor (Optional On St8130 Variant)
Power supply to Trackside beacon Air Temperature Sensor (optional on ST8130 variant) Wiring harness... - Page 62 • • • Fitting the wiring harness • • • • •...
-
Page 63: Checks And Alarms
• • Wiring labels Checks and Alarms... -
Page 64: Chapter 6. Troubleshooting
Chapter 6. Troubleshooting Symptom Possible Cause Remedy Notes Display is dead Ignition is off Turn ignition on B + is 19w connector pin (no backlight, Battery is dead Recharge or The power lead nothing on display, replace battery B - is 19w no green dial connector pin lights) - Page 65 Symptom Possible Cause Remedy Notes The Low Oil P Pressure sensor Replace sensor message does has failed NOT appear on power up. The warning light Sensor connections Check for continuity A reading of is not turned on. are faulty on sensor lead. 999 on the display indicates an...
- Page 66 Symptom Possible Cause Remedy Notes Water or Oil A temperature Disconnect temperature sensor has failed sensor and short display gives a its leads together. fixed temperature If the reading changes, replace reading of 0°C or the sensor 0°F when the water temperature is either above 12 °C or 55°F...
- Page 67 Symptom Possible Cause Remedy Notes Fixed pressure Pressure sensor Replace sensor reading of 0 PSI has failed or 0.0 Bar or suspected low/slow reading Faulty sensor Check pressure Check plumbing connections connections for a blockage (kinks in flexible hoses) All sensors show Switch 1 (Peaks) Replace switch Disconnect...
- Page 68 RPM is greater than the Gate value Internal memory Return unit to Stack Display shows !! battery dead for new battery Internal Battery service Low !! warning on power up...
- Page 69 Symptom Possible Cause Remedy Notes Switch 3: Switch 3 faulty Replace switch Disconnect switch Change and short its leads. display layer If display changes, function does replace Switch 3. not work Otherwise check wiring. Faulty switch wiring Check switch wiring Pin U to orange S3 for correct wire less than 1.0...
- Page 70 Symptom Possible Cause Remedy Notes External Bulb has burnt out Replace bulb Swap with the other warning light light to confirm dead when the burnt-out bulb. If display not burnt out, check warning light is wiring. Faulty wiring to Check continuity of Pin G to red AL light wiring.
- Page 71 Symptom Possible Cause Remedy Notes No RPM Incorrect wiring Check the See instructions speed reading connection of the supplied in this engine speed wire manual. If to the ignition connected directly system (or sensor, to the coil, check if used) that it is to the switched low tension side...
- Page 72 Symptom Possible Cause Remedy Notes Displayed speed System configured Reconfigure the value too high or with wrong number system with correct too low by a of targets per wheel values constant %-age revolution amount. System configured with wrong circumference. No speed reading Faulty sensor Check sensor Rotate the...
- Page 73 3. Check with sender unit 2. Faulty fuel your Stack from the tank, sender dealer for earth it to the 3. Fuel sender not suitable vehicle with a suitable for use...
- Page 74 Symptom Possible Cause Remedy Notes Lap time is not Lap marker Check lap marker Press lap switch displayed receiver lead faulty wiring automatically (Automatic Lap marker Replace lap marker If display receiver is fitted) receiver faulty receiver changes, replace receiver after checking its wiring.
-
Page 75: Appendix A. Template For The Display Module
Appendix A. Template for the Display Module... - Page 77 Reverse template...
-
Page 78: Appendix B. Wiring Harness Diagram
Appendix B. Wiring Harness Diagram... -
Page 79: Appendix C. Summary Of Switch Functions
Appendix C. Summary of Switch Functions Normal Operation Switch or Functions Switches Switch 1 Show the peak values Switch 2 Clear Alarm or Show Last Alarm Switch 3 Clear Alarm or Change Display Layer Switch 4 Reset the trip distance to zero and start the lap timer. The trip distance is reset after each lap. - Page 80 System Configuration Mode Switch or Functions Switches Switch 1 Decrease the alarm value of the parameter being displayed Switch 2 Increase the alarm value of the parameter being displayed Switches 1 & 2 Enable or disable an alarm for the parameter being displayed together Switch 3 Display the next configurable parameter...
-
Page 81: Returned Goods Procedure
Returned Goods Procedure... -
Page 82: Index
Index Air temperature switches to enter configuration mode, 34 alarm, 16, 21 Contact breaker system connection, 37 display, 11 Custom configured ST8130, 32 wiring label, 6 Datalogging subsystem Air temperature sensor wiring label, 6 installation, 48 Digital display panel, 5 Alarm warning light Dimensions, 33 external, 35... - Page 83 Ice warning. See Air temperature adjustment, 44 Ignition connection, 36 connection, 44 Infra-red beacon. See Beacon installation, 42 Installing the Stack ST8130, 32 specifications, 45 Internal Battery Low message, 15 Redisplaying last alarm, 17 Labels on wiring, 6 Resetting peak values, 14 Lamps.
- Page 84 Tell-tales. See Peak values Warning lights Temperature sensors alarms. See Alarm warning light installation, 40 gear shift. See Gear shift warning light Temperatures installation, 35 minimum displayable, 10 maximum power, 35 oil. See Oil temperature. See Oil Water temperature temperature alarm, 16, 21 water.
Need help?
Do you have a question about the st8130 series and is the answer not in the manual?
Questions and answers