Sewing Data Setting Item - JUKI MEB-3200 Engineer's Manual

(1) Sewing data setting item

(In case of the machine with multicutting device, refer to the item "15. MULTICUTTING DEVICE".)
Data No. Setting itm
1 Knife No.
*
2 Cut length
3 Cut-before/cut-after knife
4 Number of stitches of parallel
5 Number of stitches of eyelet
6 Cut space
*
7 Eyelet space
*
* 8 Lengthwise compensation of knife
position
9 Compensation of number of stitches at
sewing end
10 Compensation of turning
*
11 Compensation of turning at parallel
*
section
13 Crosswise compensation of eyelet
*
14 Lengthwise compensation of eyelet
*
15 Lengthwise compensation of left eyelet
16 Lengthwise compensation of left
*
parallel
17 Compensation of stitch bite width of
*
right bottom of eyelet
18 Compensation of stitch bite width of left
*
bottom of eyelet
19 Compensation of stitch bite width
*
*
20 Length of taper bar
21 Number of stitches of taper bar
* 22 Taper bar offset
23 Number of stitches of taper bar at
parallel section
24 Compensation of number of stitches of
right taper bar
25 Shape of straight bar
26 Number of stitches of round bar
27 Compensation of left knife space of
*
parallel section
28 Knife holder No.
29
30
31
32
33
34
* 35 Sewing speed
36 Reduced speed of eyelet
*
37 Soft-start
38 Number of stitches of the sewing start
39 Number of stitches of the sewing end
* Numerical value in ( ) parentheses of the setting range is the unit of set value.
Setting range
0 : Decorative, 1 to 6 : Eyelet
10 : Decorative, 11 to 16 : Eyelet
Long thread trimming : 10 to 38 mm (1 mm)
(Without looper thread trimming : 10 to 50 mm)
Short thread trimming : 16 to 26 mm (1 mm)
Short thread trimming M : 24 to 34 mm (1 mm)
Short thread trimming L : 32 to 42 mm (1 mm)
Short thread trimming without gimp :
10 to 34 mm (1 mm) T type
0 : Without knife, 1 : Cut-before knife,
2 : Cut-after knife
3 to 100 stitches
4 to 20 stitches
-1.2 to 1.2 mm (0.1 mm unit)
-1.2 to 1.2 mm (0.1 mm unit)
-0.7 to 0.7 mm (0.1 mm unit)
-1 to 6 stitches
-14 to 14 (1.125˚ unit)
-14 to 14 (1.125˚ unit)
-0.6 to 0.6 mm (0.1 mm unit)
-0.2 to 0.6 mm (0.1 mm unit)
-0.2 to 0.6 mm (0.1 mm unit)
-0.6 to 0.6 mm (0.1 mm unit)
-0.1+W to 1.0+W (0.1 mm unit)
-0.1+W to 1.0+W (0.1 mm unit)
-0.1+W to 1.0+W (0.1 mm unit)
0.3 to 15 mm (1 mm unit)
2 to 20 stitches
0.5 to 2.0 mm (0.1 mm unit)
2 to 4 stitches
-20 to 0 stitch
0 or 1 to 96
4 to 20 stitches
-2.4 to 2.4 mm (0.1 mm unit)
0 to 9
400 to 2,200 rpm (100 rpm unit)
-600 to 0 rpm (100 rpm unit)
0 to 6 needle entries
0 to 3
0 to 3
97
− −
Description
Shape of knife
0 to 6 ... Standard, 10 to 16 ... Plural times dropping
Multicutting type
(When setting straight bar/round bar for short thread
trimming, max. length becomes shorter by -2 mm.)
Operation changeover of without knife/cut-before knife/
cut-after knife
Number of stitches of parallel section + bottom of eyelet
(Pitch 0.5 to 4 mm)
Number of stitches of top eyelet (needle bar turning
section)
Clearance of knife of parallel section
Clearance of kinfe of eyelet section
Lengthwise compensation of whole needle entry position
Number os titches to increase length at sewing end
Turning compensation of parallel section + bottom of
eyelet section
Turning compensation of parallel section and eyelet
section
Crosswise compensation of bottom of eyelet Same shape
as that of top eyelet (needle bar turning section)
Lengthwise compensation of top of eyelet
Lengthwise compensation of left eyelet
Compensation of legth of left parallel section
Compensation of stitch bite width of right bottom of eyelet
(W = Stitch bite width of memory switch)
Compensation of stitch bite width of left bottom of eyelet
(W = Stitch bite width of memory switch)
Compensation of stitch bite width
(W = Stitch bite width of memory switch)
Length of taper bar
Number of stitches of taper bar (Pitch 0.5 to 2.0 mm)
Overlapping amount of left/right taper bars
Number of stitches from taper bar to parallel section
Number of stitches of compensation of right taper bar
Shape of straight bar
Number of stitches of round bar
Clearance between left parallel section and knife (= Max. of
No. 6 + No. 27 is ±1.2 mm.)
Specifying knife adjustment value 0 to 9
Max. sewing speed
Reduced speed in terms of sewing speed of eyelet
Number of stitches of soft-start at sewing start
Number of stitches at sewing start
Needle/looper thread tension
Number of stitches at sewing end
Needle/looper thread tension