Operating Instructions; Control Operation; System Mode - CalderaSpas vacanza series Owner's Manual

o I
peratInG nStructIonS

CONTROL OPERATION

Your control panel consists of an LCD display and convenient touch
pads that allow you to set the water temperature and adjust the skim/
filter cycle settings, lock spa temp, lock all spa functions, as well as
control the hydrotherapy jets, and lights.
LCD DISPLAY INVERSION
You may invert the control panel display for easier viewing from inside
the spa. To invert the display the following is required: Press the
MODE() and (-) buttons simultaneously. By pressing the MODE()
and (-) buttons simultaneously a second time the screen will go back to
it's original display.
MODE BUTTON
From the Home screen use the MODE ( or ) button to scroll to the
System, Clean, Audio (if your spa is equipped) and Tools screen. Press
the (+) button to enter into the sub screens.
Temperature

Mode
Down/Off
Filter Cycle
Temperature
1 Icon
Up /On

Mode
Filter Cycle 2
Icon
READY
SET POWER
F1
F2
TEMPERATURE CONTROL
The set temperature range is from 80°F
POWER
POWER READY
(26°C) to 104°F (40°C). Temperatures of any
setting may rise slightly depending on the
current use and condition of your spa, and
on outside temperature. Whenever power is
POWER
READY POWER
disconnected and then reconnected to the spa, the water temperature
setting will automatically return to the last temperature entered into the
program.
To increase the set temperature, press the (+) button, once for each
degree of increase temperature desired. If you hold the (+) button down,
SET
the set temperature will increase by one degree every half second.
F1
F2
To decrease the set temperature, press the (-) button, once for each
degree of decreased temperature desired. If you hold the (-) button down, the
set temperature will decrease by one degree every half second.
POWER READY

Operating Instructions

Temp Ready
Power Icon
Icon
Sleep
Icon
Filter Cycle Icon
Light Icon
Jet Icon
READY
POWER
F1
F2
READY
READY
F1
SET
F1
F2
POWER READY
F1
F2
JET PUMP CONTROL
Pressing the "JETS" button changes the jet
pump functions, depending on the number of
presses:
PALATINO, MARINO & VANTO SPA
MODELS ONLY:
• 1st press:
• 2nd press:
• 3rd press:
• 4th press:
5th press: Both Systems jet pumps are off
TARINO & AVENTINE SPA MODEL ONLY:
• 1st press:
• 2nd press:
• 3rd press:
The pump on high speed automatically turns off after operating for one
hour. The pump on low speed automatically turns off after operating for
one hour.
Jets Button
When the jets are active, the JETS icon on the control panel will
illuminate.
LIGHT - ON/OFF &
INTENSITY CONTROLS
The light control uses four positions: High, Medium, Low, and Off. To
turn on the spa light, press the LIGHT button. This will place all lights
in the spa in the High, or maximum intensity position. When the lights
turn on, the light symbol will also illuminate on the control panel display.
Light Button
Press the LIGHT button again to lower the intensity of the lights to the
Medium position. Press the LIGHT button again to lower the intensity
even more, placing the lights intensity in the Low position. Press the
LIGHT button one more time to shut the lights off. When the light is
READY
deactivated, the light symbol will also turn off.
If the lights are left on, they will automatically be turned off by the control
system after 6 hours of continuous operation. The light symbol on the
panel will also turn off when the lights are deactivated.
READY
If the lights will not turn on, make sure SPA LOCK is deactivated. SPA
LOCK disables the controls on the control panel (see following pages
for more information on SPA LOCK).
READY

SYSTEM MODE

Your spa is equipped with a System Mode. This function will allow you
to conveniently turn the jet(s) on high speed and the lights on maximum
READY intensity at the same time.
To activate the System Mode, perform the following functions:
Press the MODE ( or ) button until SYSON
is displayed on the screen. Press the (+) b utton
to activate the SYSON mode feature. The jets and
light icons will remain illuminated on the display
until the system mode is deactivated.
NOTE: Once activated, the jet and light functions can still be changed
by pressing the JETS or LIGHT button.
11
System 1 jet pump runs on low speed
System 1 jet pump runs on high speed
System 1 & System 2 jet pumps run on high speed
System 2 jet pump runs on high speed
System 1 jet pump runs on low speed
System 1 jet pump runs on high speed
Jet pump off
F2
POWER
POWER READY
F1
F2