Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for CAME ZA3N
Summary of Contents for CAME ZA3N
- Page 1 CONTROL PANEL FOR 230 V GEARMOTORS 3 19 U 4 6 EN Installation manual ZA3N...
-
Page 2: Reference Standards
2.1 Intended use The ZA3N control panel is designed to control the 230V ATI, FERNI, KRONO, FAST and FROG swing gate operators. The use of this product for purposes other than those described above and installation executed in a manner other than as instructed in this technical manual are prohibited. - Page 3 4.1 Dimensions, spans and anchoring holes (mm) 4.2 Main components 3 - Connection terminal boards 2 - Line fuse 5A 3 - Control unit fuse 3,15A 4 - Power up LED indicator 24V 5 - Buttons for memorising the radio code 6 - Operating time adjustment trimmer 7 - Trimmer for adjusting the automatic closure time...
-
Page 4: Installation
5 Installation 5.1 Preliminary checks Before installing, do the following: • Check that the panel’s anchoring point is protected from possible blows, and that the anchoring surface is solid. Also check that the anchoring is done using the appropriate bolts, screws etc. •... -
Page 5: Electrical Connections
FROG FROG Standard opening setup scheme in Came gearmotors. When using only one motor (e.g. on one leaf gates), connect it up on W X Y (M2) regardless of which side it is installed on – (fro FROG, if need be, invert connections X and Y). - Page 6 Signalling and lighting devices Open gate light-indicator (Socket rating: 24V - 3W max.). Turns on when the gate is open. It turns off when the gate is closed. Flashing light (Socket rating: 230V A.C. - 25W max.) - Flashes during opening and closing phases. Cycle lamp connection (230V-60W) This lamp lights up the vehicle manouvering area and stays on from the moment the gate...
- Page 7 Safety devices Delta-S (N.C.) contact for «re-opening during closing» - Input for safety devices such as photocells, sensitive edges and other EN 12978-compliant devices. During the gate leaves closing phase, opening the contact causes movement inversion until fully opened. If unused set DIP switch n.9 to ON (N.C.) contact of «re-closing during opening»...
-
Page 8: Selecting Functions
7 Selecting functions DIP-SWITCH 10 WAYS 1 ON Automatic closing activated (1 OFF-disactivated); 2 ON “Open-stop-close-stop” function with button (2-7) and radio control (with built-in AF card) - activated; 2 OFF “Open-close” function with button (2-7) and transmitter (with built-in AF card) - activated; 3 ON “Open only”... - Page 9 9 Motor torque limiter To vary the motor torque, shift the shown faston to one of the 4 positions: 1 min., 4 max. 10 Activating the radio control Antenna Possible output of the radio receiver’s Connect the antenna’s RG58 cable to second channel (N.O.
- Page 10 Transmitters ATOMO AT01 • AT02 see instructions attached to AT04 AF43SR card TOUCH TCH 4024 • TCH 4048 TOP-432NA • TOP-434NA TOP-862NA • TOP-864NA TOP-432S T132 • T134 • T138 T152 • T154 • T158 TOP-432A • TOP-434A TOP-302A • TOP-304A T432 •...
-
Page 11: Disposal Of Packaging
In its premises, CAME S.p.A. implements an Environmental Management System certified in compliance with the UNI EN ISO 14001:2004 standard to ensure environmental protection. Please continue our efforts to protect the environment—which CAME considers one of the cardinal elements in the development of its operational and market strategies—simply by observing brief recommendations as regards disposal: DISPOSAL OF PACKAGING The packaging components (cardboard, plastic, etc.) are all classifiable as solid urban waste products and may be disposed of easily,... - Page 12 Came S.p.A. Came S.p.A. Via Martiri Della Libertà, 15 Via Cornia, 1/b - 1/c 31030 Dosson di Casier Dosson di Casier 33079 Sesto al Reghena Sesto al Reghena Treviso Treviso - Italy Pordenone Pordenone - Italy (+39) 0422 4940 (+39) 0434 698111...
Need help?
Do you have a question about the ZA3N and is the answer not in the manual?
Questions and answers