Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Parker IQAN-G11
Summary of Contents for Parker IQAN-G11
- Page 1 IQAN-G11 Instruction book Publ no HY33-8416-IB/UK Edition 2016-05-09...
-
Page 2: Table Of Contents
Appendix A ........... 14 IQAN-G11 Technical Overview ........14 Absolute Maximum Ratings . -
Page 3: Introduction
Contains IC: 772C-LBZY Contact the manufacturer if there is anything you are not sure about or if you have any questions regarding the product and its handling or maintenance. The term "manufacturer" refers to Parker Hannifin Corporation. Instruction book, IQAN- G11... -
Page 4: Precautions
Operation IQAN-G11 receives and transmits radio frequency energy while switched on. Follow any special regulations and always switch off the IQAN-G11 wherever forbidden, or when you suspect that it may cause interference or danger. Disposal Observe your local/national regulations when disposing the device and its package. - Page 5 Additional information for diagnosing the system For information, see Appendix B, on page 16, in this document. OTICE It is required to download the operating system 4.01 or later to enable full functionality of the IQAN-G11 in IQANdesign platform systems. Instruction book, IQAN- G11...
-
Page 6: Quick Start Guide
IQAN-G11 with your mobile device, the IQANsync app and IQANconnect. IQANdesign set up for IQAN-G11 support. To use an IQAN-G11, you must add it in the application and connect it to the diagnostic bus (available from IQANdesign 4.01 and later). - Page 7 • to have a digital channel that detemines when it is safe to allow a remote connec- tion. Without a display operators cannot acknowledge the ”ask user” alternative. Set security property to always allow use of IQAN-G11 and IQANconnect in IQANdesign. OTICE The "always" option is not the most secure example, for better security it is recommended to use an input to allow a remote stop.
-
Page 8: Product Description
The communication interfaces are used for uploading/downloading applications or diagnostics and typically communicate with an IQAN master module. The IQAN-G11 has 1 CAN interface. It is located in the Deutsch DT 4 pin connector and is used to interface with IQAN master modules (e.g. IQAN-MD4). -
Page 9: System Diagnostics
Communication Product description System Diagnostics The IQAN-G11 has 1 bi-color LED light on front surface indicating system status and dongle status. status led Location of status LED. For more information about the status and error messages, see Appendix B, on page 16. -
Page 10: Markings And Approvals
Communication Markings and approvals Markings and approvals Declaration of Conformity Instruction book, IQAN- G11... -
Page 11: Mounting
• Locate the module so the LED is visible. Mounting orientation of the IQAN-G11. OTICE The IQAN-G11 module must not be placed in any marine related or similar continuously damp environment without external protection. Instruction book, IQAN- G11... -
Page 12: Installation
Connector Installation Installation Connector Connector kit Parker no. 5031113 Housing DT06-4S Wedge Sockets 1062-16-0122 Connector pin assignments Logical (I)nput or Function description Symbol (O)utput and/or Signal name(s) -BAT Power supply, negative ground +BAT Power supply, positive CAN-L CAN low CAN-H... -
Page 13: Supply Voltage
1 A (Fast) is being used. If this fuse is not used, polarity reversal can damage the unit. OTICE IQAN-G11 does not have load-dump protection and must be mounted within approx 2 meters from a unit with load-dump protection. Instruction book, IQAN- G11... -
Page 14: Communication
A connection will be charged against your IQANconnect subscription whenever you initiate communication with a system. CAN termination If the IQAN-G11 is located at the end of the CAN bus, it must have a termination resistor installed to terminate the bus. IQAN-G11 CAN-H pos. -
Page 15: Start-Up
Start-up procedures Start-up Start-up Start-up procedures This chapter contains instructions for action to be taken in connection with the initial start. ARNING Risk of injury! If the control system is not fitted properly, the machine could move uncontrollably. The machine’s engine shall not be started before the control system is completely fitted and its signals are verified. -
Page 16: Iqan-G11 Technical Overview
IQAN-G11 Technical Overview Appendix A Appendix A IQAN-G11 Technical Overview Absolute Maximum Ratings Limit values Parameter Unit Remark min. typ. max. Ambient temperature, T – 40 °C Storage temperature, T – 40 +105 °C Voltage supply on +BAT Reverse polarity protected with 1A fuse. -
Page 17: System
IQAN-G11 Technical Overview Appendix A System = +25 °C (unless otherwise specified) Limit values Parameter Unit Remark min. typ. max. Weight grams Ambient temperature – 40 °C Voltage supply, V Current consumption @14 Vdc @28 Vdc Approvals Parameter Remark FCC (United States... -
Page 18: Led Messages And Actions
If an error is detected, a message will be presented on the LED. ARNING An error message could indicate that a hazardous situation exists. If precautions are not taken, this could result in death, serious injury or major property damage. LED indicators showing different IQAN-G11 modes Status Flash (yellow) Init... -
Page 19: Dimensioning Of The Iqan-G11 Module
Dimensioning of the IQAN-G11 module Appendix C Appendix C Dimensioning of the IQAN-G11 module 37,6 27,75 Unit = mm Instruction book, IQAN-G2... - Page 20 For latest information visit our website www.iqan.com Information in this instructionbook is subject to change without notice Publ no HY33-8416-IB/UK Edition 2016-05-09 Parker Hannifin Parker Hannifin Electronic Controls Division Electronic Controls Division SE-435 35 Mölnlycke 1651 N. Main Street Sweden...
Need help?
Do you have a question about the IQAN-G11 and is the answer not in the manual?
Questions and answers