1. Manuals
  2. Brands
  3. EDS Manuals
  4. Smoke Alarm
  5. RK 100 R
  6. Technical manual

EDS RK 100 R Technical Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
EDS - TECHNICAL INSTRUCTIONS
REFLECTIVE TYPE
OPTICAL BEAM LINEAR

SMOKE DETECTOR

RK 100 R
RK 100 RS
TECHNICAL MANUAL
TECHNICAL INSTRUCTIONS FOR
INSTALLATION, SETUP AND
MAINTENANCE
1
EDS - V. Ca' Nova Zampieri 6 - 37057 S. G. Lupatoto - VERONA - Tel. +39045547529 - Fax. +390458750065 - E.Mail: eds@eds.eu - Web: www.eds.eu

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RK 100 R and is the answer not in the manual?

Questions and answers

Related Manuals for EDS RK 100 R

Summary of Contents for EDS RK 100 R

  • Page 1: Smoke Detector

    RK 100 R RK 100 RS TECHNICAL MANUAL TECHNICAL INSTRUCTIONS FOR INSTALLATION, SETUP AND MAINTENANCE EDS - V. Ca' Nova Zampieri 6 - 37057 S. G. Lupatoto - VERONA - Tel. +39045547529 - Fax. +390458750065 - E.Mail: eds@eds.eu - Web: www.eds.eu...

  • Page 2: Table Of Contents

    CHAPTER INDEX The procedure below is intended for trained personell with previous 1 - Qualified Personell experience in installing EDS Beam Smoke Detectors RK100R. 2 - Relevant Standards If you don’t have the needed experience please refer to the standard installation procedure of this manual.

  • Page 3: Qualified Personell

    EDS - TECHNICAL INSTRUCTIONS REFLECTIVE TYPE OPTICAL BEAM SMOKE DETECTOR RK100R - RK100RS GENERAL The RK100R detector is a newly-conceived microprocessor optical beam smoke detector, that bases its working concept on the interaction between the smoke present in a room and an infrared beam emitted by a transmitter and reflected by an optical reflector (fig.1).

  • Page 4: Electrical Connections And Initial Setup

    • JP1 position 2-3 (ON)..alignment procedure ON able to project a concentrated and sufficiently intense light beam. (we recommend the EDS alignment lamp LAL02) • JP1 posizion 1-2 (OFF)..alignment procedure OFF • direct the light beam of the lamp to the lenses of the detector •...
  • Page 5 EDS - TECHNICAL INSTRUCTIONS what’s following • 1 flash of the blue Led: 1 Volt 8.6 - the P1 trimmer (regulation of the signal level) is regulated in • 1 flash of the red Led: 0.5 Volts factory to the 50-60% and it corresponds to a signal of 5V to the •...

  • Page 6: Detector's Activation

    EDS - TECHNICAL INSTRUCTIONS situation. The setting must normally be a medium sensitivity level, 10.5 - Stopped this phase of adjustment, the detector becomes but in case of dusty and perturbed environments it will be useful to operational. The blue Led of Alignment stops (detail cap.10.2) and set a lower sensitivity level.

  • Page 7: Alarm Memory

    Type: Reflective Type Optical Beam Linear Smoke Detector • jumper JP5 in position 1-2 - memory not activated (OFF) • Manufacture: EDS srl - V. Cà Nova Zampieri 6 - 37057 S.G. • jumper JP5 in position 2-3 - activated (ON) Lupatoto - Verona - Italy When the memory is activated, if the detector goes to alarm, the •...
  • Page 8 EDS - TECHNICAL INSTRUCTIONS disco bianco white disc rivelatore riflettore foro hole diodo fotoemittente photoemitting diode fig.1 fig.4 fig.5 fig.2 diametro del raggio [cm] lampada LAL 02 rivelatore distanza [m] fig.3 fig.6...
  • Page 9 EDS - TECHNICAL INSTRUCTIONS DISTANCE SELECTION WITH JP7 Distance REFLECTOR Position fig.7 ° N ° N < a i r , 4 - g i l fig.8 > g i l g i l r u t i t a...
  • Page 10 EDS - TECHNICAL INSTRUCTIONS DS1649 LED di Allineamento LED di Allarme Relè Guasto fault Fehlerrelais relay Turbo Relè turbo Turborelais relay TURBO SENS POWER Relè Allarme alarm Alarmrelais relay fig.9 INTERNAL PARTS P1 - Trimmer for the regulation of the signal level. Normally regulated to 50-60% that corresponds to a signal of 5V at the maximum distance.
  • Page 11 EDS - TECHNICAL INSTRUCTIONS DS1650 LED di Allineamento LED di Allarme Relè Guasto fault Fehlerrelais relay Turbo Relè turbo Turborelais relay TURBO SENS POWER Relè Allarme alarm Alarmrelais relay fig.10 INTERNAL PARTS WITH STS-01 METER segnale analogico 0-5V analog signal output 0-5V contatto relè...
  • Page 12 EDS - TECHNICAL INSTRUCTIONS Example of RK100R connection with a zones Control Unit CENTRALE DI CONTROLLO alimentazione connessione zona1 segnale analogico 0-5V schermo contatto relè GUASTO resistenza di Allarme contatto relè TURBOLENZA contatto relè d'ALLARME resistenza di fine linea alimentazione 11-30 Vcc fig.12...
  • Page 13 40x60mm (dimensions) The information contained in this document have been carefully checked and are reliable. By the way EDS company is not responsable in any way for possible inaccurancies or errors and it reserves the right to perform changes in any part of this document and/or product, to improve the quality, reliability or the design.
  • Page 14 Agreement is not an admission or agreement that the design or manufacture of a product is defective. EDS - V. Ca' Nova Zampieri 6 - 37057 S. G. Lupatoto - VERONA - Tel. +39045547529 - Fax +390458750065 E.Mail: eds@eds.eu Web: www.eds.eu...

This manual is also suitable for:

Rk 100 rs

Table of Contents