resi-linx RL-BT100 Installation Manual

www.resi-linx.com
INSTALLATION MANUAL
A
Balanced
Audio Output
B
Balanced
Audio Input
C
IR Target Input
D
ANT
G
Mini USB
LED Indicator Input
H
Includes:
RL-BT100 Bluetooth In-Ceiling Amplifier
TIM module
Remote Control
Direct Power Adapter
Bluetooth Antenna
Power Supply
Mini USB to USB lead

Cabling Instructions

Wiring:
1. Run low loss speaker cable from RL-BT100 Amplifier
Speaker Terminals F to speakers.
Wiring to another RL-BT100:
2. For connection to another RL-BT100 Amplifier run twisted
pair cable from the Output A of the 'Master' Amplifier unit
(first in line) to Input B of the 'Slave' Amplifier unit/s.
Wiring to RL-BT430:
3. For connection to RL-BT430 Input Module run BOTH a
twisted pair cable from Audio Input B and a Figure 8
Power Cable from Power Input E of RL-BT100 Amplifier to
RL-BT430 unit.
Hardware Connection
1. Connect speaker cable to Speaker Terminals F . For
optimum performance ensure that speaker polarity is
consistent ie:
- Left Positive output (L+) on RL-BT100 is connected to
the Positive (+) Input on Left speaker
- Left Negative output (L-) on RL-BT100 is connected to
the Negative (-) Input on the Left speaker
- The same wiring must apply to the Right speaker
connections
2. Screw antenna supplied onto Antenna Input D .
3. Drill 16mm hole for mounting of TIM module into plaster
ceiling optimally 750mm distance from left or right speaker
location.
WARRANTY
Australian Audio Imports Pty Ltd states that the warrant that the customer can rely on is that provided
by the manufacturer. In the event of any warranty claim please contact us and we will forward it to the
manufacturer. The manufacturer will then determine the extent of their liability. This expressly negates, to
the extent possible by Australian law, any warranty reliance on Australian Audio Imports Pty Ltd. Warranty
will be void if product/s are not installed as per supplied instructions.
®
linx-Audio
RL-BT100
linx-Audio Bluetooth
24V DC
E
R+
R-
Speaker
F
8 ohm
L-
L+
Cable Requirement*:
Audio - Category 5e twisted pair cable
Power - Figure 8 14-020
Speaker - 12-24 AWG Low Loss Speaker Cable
Notes:
1. Recommended cables are run according to TS009
regulations to reduce interference
2. Maximum cable run of twisted pair from Amplifier to
RL-BT430 is 40m
3. Maximum cable run of twisted pair cable from RL-BT100
Amplifier to second Amplifier is 25m
4. RJ45 termination type EIA/TIA 568A wiring standard
*Refer to diagram pg2
4. Connect TIM module BLACK cable into LED Indicator Input H
and RED cable into IR Target Input C on RL-BT100 3.5mm
jack (corresponding coloured socket).
5. Place RL-BT100 in ceiling space within easy reach of ceiling
access hole if available (to allow for future accessibility).
Connection to RL-BT430
6. Refer to instruction sheet RL-BT430
Power Connection
7. When cabling to all system components has been completed
and checked, plug power adapter (supplied) into mains and
plug DC jack into Power Input E on RL-BT100.
8. To change power supply to direct power: terminate Figure 8
Power Cable into supplied Direct Power Adapter and connect
to DC Power Input E .
All trademarks and trade names are those of their respective owners. The Bluetooth
word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any
RL-BT100
Bluetooth In-Ceiling Amplifier
Balanced Audio Output
A
Balanced Audio Input
B
IR Target Input
C
Antenna
D
Power Input 24V DC
E
(via Power Supply or RL-BT430/Direct Power Adapter)

Speaker Terminals

F
Mini USB
G
LED Indicator Input
H
Australian Audio Imports Pty Ltd
use of such marks by Australian Audio Imports Pty Ltd is under license.
Australian Audio Imports
Range
®
ABN: 34 005 281
®