Table of Contents
Advertisement
Service
Battery Removal
WARNING!
accessories contain lead and lead compounds. Wash
hands after handling.
The battery is located beneath the seat box frame. To remove the
battery:
1.
Remove the hold down strap.
2.
Remove the hex screw and flange lock nut securing the black
negative battery lead to the negative battery post (marked
NEG). Move the cable away from the negative battery post.
3.
Remove the hex screw and flange lock nut securing the red
positive battery lead to the positive battery post (marked POS).
4.
Carefully lift the battery out of the tractor.
5.
Install the battery by repeating the above steps in the
reverse order.
WARNING!
the battery before connecting the negative lead.
This will prevent sparking or possible injury from an
electrical short caused by contacting the tractor
body with tools being used to connect the cables.
Charging the Battery
Test and, if necessary, recharge the battery after the tractor has
been stored for a period of time.
•
A voltmeter or load tester should read 12.6 volts (DC) or
higher across the battery terminals. See Figure 6-1.
Voltmeter
Reading
12.7
12.4
12.2
12.0
•
Charge the battery with a 12-volt battery charger at a
MAXIMUM rate of 10 amps.
Jump Starting
WARNING!:
can cause sparking, and the gases in the battery to
explode.
1.
Connect the end of one cable to the disabled machine
battery's positive terminal; then connect the other end of
that cable to the booster battery's positive terminal.
2.
Connect one end of the other cable to the booster
battery's negative terminal; then connect the other end of
that cable to the frame of the disabled tractor, as far from
the battery as possible.
34
Battery posts, terminals and related
Always connect the positive lead to
State of
Charging
Charge
Time
100%
Full Charge
75%
90 Min.
50%
180 Min.
25%
280 Min.
Figure 6-1
Failure to use this starting procedure
3.
Start the disabled tractor following the normal starting
instructions previously provided; then disconnect the
jumper cables in the exact reverse order of their connection.
4.
Have the tractor's electrical system checked and repaired
as soon as possible to eliminate the need for jump starting.
Servicing Electrical System
Fuse
There is a fuse located inside the left console. Lift the seat and
look down at the left console to find the location of the fuse. A
25 amp for fuse the ignition, PTO, etc. This is a standard plug-in
type automotive fuse. Always use the same capacity fuse for
replacement. Check the fuse for all electrical problems.
If you have a recurring problem with blown fuses, have the tractor's
electrical system checked by your Cub Cadet Service Dealer.
Safety Switch Operation Checks
The following operational checks should be made daily:
PTO Switch
1.
Sit in the operator's seat. With the drive levers are in the
neutral position and the parking brake engaged, engage
the PTO switch by pulling up on the knob and try to start
the engine. The engine should not start. If it does, the PTO
switch must be replaced. See an authorized service dealer.
2.
If the engine does not start, disengage the PTO by pressing
the knob down and start the engine. Now engage the PTO
and the blades should rotate.
3.
If the blades do not turn, the PTO switch must be replaced,
the seat switch must be replaced or the electric PTO clutch
must be repaired. See an authorized service dealer.
Parking Brake Switch
•
Sit in the operator's seat. With the drive levers in the neutral
position and the PTO disengaged, release the parking brake
and try to start the engine. The engine should not start.
•
If it does, the parking brake switch must be repositioned or
replaced. See an authorized service dealer. If the engine does
not start, engage the parking brake and start the engine.
Seat Switch
•
With the drive levers in the neutral position, the parking
brake engaged and the PTO disengaged, start the engine.
Now release the parking brake, and raise up off the seat.
The engine should stop. If the engine does not stop, the
seat switch must be replaced. See an authorized service
dealer.
•
With the drive levers in the neutral position, the parking
brake engaged and the PTO disengaged, sit in the operator's
seat and start the engine. Engage the PTO and the blades
should start to rotate. Raise up slightly off the operator's seat
and the blades should stop. If the blades do not stop when
you dismount from the operator's seat, the seat switch must
be replaced. See an authorized service dealer.
7
Hide quick links:
Advertisement
Table of Contents
