Canon VB-R10VE Installation Manual

Network Camera
/ Installation Guide
Please be sure to read the "Safety Precautions" section for correct use. After reading this Installation
Guide, keep it in a readily accessible location for future reference.
* Some cameras are not available in certain countries or regions.
Caution
Request a professional installer for all installation work. Never try to install the camera yourself.
Doing so may result in unforeseen accidents such as dropping the camera or electric shock.
Check Included Items
Camera Installation Guide (This document) Setup CD-ROM
Warranty Card Notice Dedicated wrench
Power Interface Cable
I/O Interface Cable (BK2-0035-000)
Power Interface Cable (Waterproof)
LAN Connector Set (Waterproof)
Symbols Indicating Camera Model
Camera specific functions will be listed using the symbols below.
: VB-R11VE : VB-R10VE
© CANON INC. 2015
Accessories
The following accessories can be purchased separately as necessary. Some accessories are not available in
certain countries or regions.
Ceiling Mounting Kit CM10-VB
Dedicated accessory for attaching the camera to the ceiling.
Wall Mounting kit WM10-VB
Dedicated accessory for attaching the camera to a wall surface.
1.5inch Pipe Adapter PA10-15-VB
Dedicated accessory used to install the camera to the end of pipe that extends from high ceilings, such as in big-box
stores.
Dome Unit DU10-S-VB
Smoked dome cover.
Canon AC Adapter PA-V18
Dedicated AC adapter for this camera.
Part Names
6
8
7
1 2 3 4 5
9
12
11
10 13
Serial_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
MAC_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
14 15
1. Power connection terminal / 2. External device I/O terminals /
3. Audio input terminal (Black) (common LINE IN and MIC IN) /
4. Audio output terminal (White) (LINE OUT) / 5. 100Base-TX LAN connector /
6. Attachment screws / 7. Power connection terminal / 8. Waterproof LAN connector
9. Dome case / 10. Reset switch / 11. Reboot switch / 12. Lens / 13. LED (Orange) / 14. Memory card slot /
15. LED (Blue)
Before installing the camera
Set the IP address and other network information on the camera using the "Camera Management Tool" on the
Setup CD-ROM. For details on how to operate the "Camera Management Tool", please refer to the "Camera
Management Tool User Manual".
Separating the Camera and Attachment
❶
❸
Note
❷
Please unhook the
safety wire connected
to the camera.
Removing and Attaching the Dome Case
Removing the Dome Case Attaching the Dome Case
Loosen the screws holding the dome case in place with the (1) Fix the screws in the dome case and
dedicated wrench, and remove it. Loosen the screws on the dome attach the safety wire.
case to detach the safety wire. (2) Align the dome case with the camera
body.
(3) Tighten the
Dedicated
dome case
wrench
screws with
the dedicated
wrench.
BIE-7070-001
Using a Memory Card
ENGLISH
Remove the dome case and place the memory card in the memory card
slot.
To remove the memory card, push it in all the way until the card slightly
pops out and remove.
Important
• Insert a memory card before installing the camera.
• When using a memory card with the camera for the first time, it is
recommended to format the card after inserting it into the camera (please refer
to "Operation Guide" > "Setting Page" > "Memory Card").
Memory card slot
• Always unmount the memory card before removing it (please refer to
"Operation Guide" > "Setting Page" > "Memory Card").
Using the Dome Unit (sold separately)
Remove the dome case from the camera, then remove the dome cover holder and dome flange, and replace with
the smoked dome.
• Take care when replacing so as not to scratch the
Dome flange
• For proper protection against water and dust,
Printed in Japan
Rubber Seal
Dome cover
Dome cover holder
Dedicated wrench
Using the LAN Connector Set (Waterproof)
Attach the LAN cable to the connector as shown below.
❶ ❷
7.5 - 8.6 mm
( 0.30 - 0.34 in.)
6.1 - 7.5 mm
( 0.24 - 0.30 in.)
4.9 - 6.1 mm
( 0.19 - 0.24 in.)
/
❹ ❺
568B
568A
❻ ❼
❽ ❾
Installing the Camera
1
Attached to ceilings/Attached to walls
The camera is installed with the optional ceiling mounting kit (sold separately) or wall mounting kit (sold separately). If it is not possible to drill a hole in the ceiling
or wall for wiring purposes, a composite pipe can be used instead.
Please refer to the installation guide included with the optional ceiling mounting kit and wall mounting kit for further details.
1 -1
Ceiling Installation
a
Important
dome cover.
please make sure the screws are firmly tightened
Wall Installation
during installation.
a. Box Unit
2
2 -1
❸
b
Smoked dome cover
b. Joint Unit
2 -2
❷
❶
c. Shaft
2 -3
Attached to ceilings/Attached to walls
❸
14 - 16 mm
(0.55 - 0.63 in.)
24 - 26 mm
(0.94 - 1.02 in.)
Wire Manager
Note
e. I/O interface cable
f. Power interface cable
Align the wires with the
terminal settings according 2 -4
to the 568B/568A color
Attached to ceilings/Attached to walls
coded illustration, and
insert them into the wire
manager.
g
g. TORX T30 Driver
3
1 -2 1 -3
a
2 -1
Dedicated wrench
❸
Dedicated
b
wrench
❶
❷
❷
❶
❷
2 -2
❶
Ceiling pendant mounting
e
2 -3
f
e
Note
f
Wrap the cable connection
with waterproof tape.
2 -4
Ceiling pendant mounting
❸
g
Dedicated
❶
wrench
❷
4 5
❶
❷
❷
❶
Ceiling pendant mounting
Mount using the 1.5inch Pipe Adapter (sold separately).
For details please refer to the Installation Guide included with the
kit.
1 -1 1 -2
❷
3.0 cm (1.2 in.)
Pass necessary cables ❸
for connecting the camera M3
through the pipe.
Included with 1.5inch
Pipe Adapter
❷
❷
c
c
❶
❶ b
b
d
d
b. Joint Unit
c. Shaft
d. LAN cable
Using the Power Interface Cable (Waterproof)
Note
Cut off the cap if the power interface
cable (Waterproof) is to be used.
d
Keep the cut-off cap in a safe
location. If the cap is not attached
when the power interface cable
(Waterproof) is not being used, it
may result in the accumulation of
water, which will damage the camera
body.
Dedicated wrench
❸
❶
❷
To 3 for ceiling pendant
mounting
Attached to ceilings/Attached to walls
g
g
g. TORX T30 Driver
6 7
Dedicated
wrench
❶