Page 1
SERVICE MANUAL RDS MP3/WMA CD Receiver TO ALPINE Home Page 3 / 05-A 68E38373S01 CDA-9853R...
Page 2
<Cautions for Safe Repair Work> The following cautions will prevent accidents in the workplace and will ensure safe products. *The symbols indicate caution is needed to prevent injuries and damage to property. The symbols and their meanings follow. If you ignore this symbol and handle the product incorrectly or unsafely, Warning serious injury or death may result.
CDA-9853R Contents Packing Assembly Parts List Packing Method View Specifications 5 , 6 Extension Cable Adjustment Procedures 8 to 11 Block Diagram Parts Layout on P.W.Boards and Wiring Diagram 13 to 16 Schematic Diagram 17 to 22 Terminal Voltage of IC/TR...
CDA-9853R Specifications < FM RADIO > Intermediate Frequency ........................10.7±0.1MHz Frequency Range ........................... 87.5 to 108.0MHz Usable Sensitivity (30dB S/N, Mono, at 98.1MHz) ..................20.2dBf -3dB Limiting Sensitivity (at 98.1MHz) ......................20.2dBf Residual Noise (Ref. 400Hz (narrow), at 98.1MHz) ..................30±10dB S/N Ratio (at 98.1MHz)
CDA-9853R Extension Cable *Always connect the Extension Cable when making checks of voltage and repair. MAIN P.W.Board (1) 01E36492S01 (2) 01E29154S01 CB101 CD Deck Mechanism CB501 (DP23S8DA) FRONT P.W.Board CB104 CH401 TO CONTENTS - 7 -...
Page 9
CDA-9853R (3) Control Settings Power Switch ..........ON Band Switch ......FM/MW/LW Fader Control ......Center Position T-CORR ........Non Effect Balance Control ....... Center Position ............FLAT Treble Control ......Center Position DEMO ........... OFF Bass Contro ......Center Position Others ...........
Page 10
CDA-9853R Test Point / Step Description Connection Signal Generator Dial Control P.W.Board Adjustment Coordinates TP002 Auto Adjustment : 216kHz, (3-F) After setting up of Signal Genarator, 34dBµ 216kHz TP501 short GND and TP501 (Pull-Down) (Mod. OFF) (3-F) for 2~3 seconds.
Page 11
CDA-9853R Test Point / Step Description Connection Signal Generator Dial Control P.W.Board Adjustment Coordinates Set up of Adjustment Mode BAND + Push at the same time. 98.1MHz, Rotary encoder is turned and noise level Noise Level Audio Output is adjustment.
CDA-9853R Block Diagram Pre IN/OUT Selector Slide SW Tuner unit Ai-Net E-VOL Tre/Bass Selector Vol.1 Vol.2 Pre-OUT Buffe Buffer MUTE Sub Woofer Pre-OUT Buffe Buffer MUTE Front DSP+5V Pre-OUT Buffe Buffer MUTE Rear RDS Decoder MUTE OEM SUB Tuner on...
Page 13
Parts Layout on P.W.Boards and Wiring Diagram(1/4) CDA-9853R TO CONTENTS MAIN P.W.Board (Component Side View) ET601 ASSY,AMP LINK53A DIN801 IC803 CB803 IC307 F801 C816 D395 C815 D809 JK301 D393 D802 C801 E390 E389 Q516 E104 R803 R804 R832 VT001 L001...
Page 14
Parts Layout on P.W.Boards and Wiring Diagram(2/4) CDA-9853R TO CONTENTS MAIN P.W.Board (Foil Side View) R595 C839 R591 C822 C818 R553 C842 C841 D394 R533 C838 C821 R857 R805 C824 D390 C840 Q806 R599 R829 Q808 Q514 C102 C388 R574...
Page 15
Parts Layout on P.W.Boards and Wiring Diagram(3/4) CDA-9853R TO CONTENTS FRONT P.W.Board (Component Side View) SW405 LCD401 SW406 IC405 SW422 R498 LD466 LD465 C412 Q421 SW408 R474 R475 LD450 LD442 LD418 LD446 R477 SW411 SW412 LD444 R4023 SW414 SW418 SW420...
Page 16
Parts Layout on P.W.Boards and Wiring Diagram(4/4) CDA-9853R TO CONTENTS DP-S MAIN P.W.Board (Foil Side View) The patterns should be short-circuited, when the PICKUP is removed TP59 TP58 E102 from DP-S Mechanism. R102 C104 R104 C144 Q101 TP175 TP62 R103...
Page 25
CDA-9853R IC307 Voltage Note Voltage Note Voltage Note 7.62 1.72 14.3 7.62 7.62 4.85 7.62 1.63 7.62 14.3 1.47 7.62 1.33 3.59 7.62 7.62 IC401 Voltage Note Voltage Note Voltage Note 1.39 1.44 5.02 0.02 5.02 5.02 0.02 5.02 5.02 0.02...
Page 26
CDA-9853R IC402 Voltage Note Voltage Note Voltage Note 3.43 1.82 0.23 -1.37 -2.96 2.06 5.02 -9.78 -7.34 2.52 -2.34 2.52 0.02 5.02 0.02 5.02 0.02 0.02 0.34 0.02 IC403 Voltage Note Voltage Note Voltage Note 5.02 3.04/0.09/ BLUE/GRN/ 2.63/3.18 AMB/RED 0.08/2.79/...
Page 27
CDA-9853R IC405 Voltage Note 4.86 4.62 IC501 Voltage Note Voltage Note Voltage Note 3.33 3.33 4.95 3.33 3.33 0/3.33 3.33/0 TUNER/CD NOSE CLOSE/OPEN 3.33 3.33 3.33 0/3.27 3.33 0/3.33 2WAY/3WAY 3.33 0/3.33 NOSE CLOSE/OPEN 2.55 3.33 0/3.33 3.33 BUZZER OFF/ON 1.17...
Page 28
CDA-9853R IC504 IC505 Voltage Note Voltage Note 8.68 4.95 4.95 IC507 Voltage Note Voltage Note Voltage Note 3.33/0 POW IC ON /OFF 4.9/0 3.33 IC508 Voltage Note Voltage Note 0/3.33 RESET ON/OFF 1.27/3.33 RESET ON/OFF 1.77/0 RESET ON/OFF IC509 Voltage...
Page 29
CDA-9853R IC604 IC605 Voltage Note Voltage Note 4.95 4.95 4.95 IC802 Voltage Note Voltage Note Voltage Note 12.43 0/5.97 ANGLE action 12.43 0/4.4 ANGLE action 0/4.4 ANGLE action 0/4.7 ANGLE action 0/4.7 ANGLE action 0/4.4 ANGLE action IC803 Voltage Note...
Page 35
CDA-9853R IC303 CD-DA PLAY MP3 PLAY 0.00V 0.00V 0.00V 0.00V PULSE : 3.17V (when disc scratch is detected) 3.17V 3.17V 0.00V 0.00V 0.00V 0.00V PULSE : 3.17V (when disc scratch is detected) 0.00V 0.00V 3.17V 3.17V 3.17V 3.17V IC304 CD-DA PLAY MP3 PLAY 1.65V...
Page 36
CDA-9853R Q101 Q102 CD-DA PLAY MP3 PLAY CD-DA PLAY MP3 PLAY 2.54V 2.56V 3.20V 3.22V 2.24V 2.26V 1.66V 1.66V 3.20V 3.18V 3.24V 3.22V Q301 CD-DA PLAY MP3 PLAY 0.00V 0.00V PULSE : 3.17V (when disc scratch is detected) 0.00V 0.00V 3.17V...
Page 37
CDA-9853R Description of IC Terminal D70F3263YGC : IC501 Symbol Terminal Description AVref1 AVref power supply input terminal. (connect to VDD) AVss GND connect terminal for A/D Converter. DSP CLK DSP CLOCK output terminal. DSP DATA I/O DSP DATA output terminal.
Page 38
CDA-9853R Symbol Terminal Description F-START Front u-COM communication start output terminal. F-RESET Front u-COM RESET signal output terminal. AMP DATA IN AMP LINK DATA input terminal. AMP DATA OUT AMP LINK DATA output terminal. AMP CLK AMP LINK CLOCK output terminal.
Page 39
CDA-9853R Symbol Terminal Description Multi-Path signal input terminal. AFC signal input terminal. SSTOP SEEK STOP input terminal. TUNER S/M level input terminal. NOSE DET NOSE installation detect terminal. D70F3033BGC : IC401 Symbol Terminal Description ENCODER-1 ENCODER input terminal. No connect terminal.
Page 40
CDA-9853R Symbol Terminal Description LCD CLK Clock signal output terminal to LCD DRIVER. LCD CS1 A CE signal output terminal to LCD DRIVER. LCD A0 A Address bus selection signal output terminal to LCD DRIVER. LCD DI A Serial data output terminal to LCD DRIVER.
Page 41
CDA-9853R TMP91CP27UG : IC104 (DP23S8DA) Symbol Terminal Description VREFL GND connect terminal for system BATT. NC(PULL-DOWN) E2CE(PULL-DOWN) Pull-down connect terminal. NC(PULL-DOWN) QDATAF TEXT DATA confusion sync. signal output terminal for HOST interface. /FIN Frame input terminal from HOST u-COM. REQ signal input terminal for Decoder (TC94A20F) interface.
Page 42
CDA-9853R Symbol Terminal Description /BOOT BOOT output terminal for Flash u-COM rewriting. No connect terminal. /DEC_RESET Decoder (TC94A20F) RESET output terminal. DEC_STANDBY Decoder (TC94A20F) STANDBY output terminal. No connect terminal. NC(PULL-DOWN) Pull-down connect terminal. DATA input/output, EEP-ROM DATA input/output combination terminal for Decoder (TC94A20F) interface.
Need help?
Do you have a question about the CDA-9853R and is the answer not in the manual?
Questions and answers