To Remove The Battery - Yardworks 060-2293-6 Instruction Manual

6
model no. 060-2293-6 | contact us: 1 866 523 5218
BATTERY IMPORTANT! The battery is not shipped fully charged. It is recommended that
the battery be fully charged before the initial use. With regular use, the battery pack will take
90 MINUTES or less to charge fully. It is recommended that the battery be charged every 3
months when the trimmer is not in use. The battery's run time will improve after the third or
fourth charge.

TO REMOVE ThE BATTERY

1. Press in and hold the latch buttons ( 1 ) on both side s of the battery pack.
2. Grasp the trigger handle (2) firmly. Pull the battery pack out of the handle.
3. NOTE: The battery pack fits snugly into the handle to prevent accidental dislodging. It
may require a strong pull to remove.
TO INSTALL
1. Align the tongue (3) of the battery pack with
the cavity in the handle housing.
2. Grasp the trigger handle (2) firmly.
3. Push the battery pack into the handle until
both sides lock. The latch buttons will click
when they lock.
4. Do not use force when inserting the battery
pack. It should slide into place and click.
GUARD
1. Remove the battery pack.
2. Invert the grass trimmer to access the trimmer
head.
3. Using a Phillips head screwdriver, remove th e pre-
installed screw (1) from the trimmer head.
4. Place the guard (2) on to the trimmer head and turn
the guard 45° following the track on the head.
5. Align the screw hole on the guard with the screw
hole on the trimmer head.
6. Insert the screw into the trimmer head, fastening
the guard in place.
To avoid injury and to reduce the risk of electric
WARNING!
!
shock or fire:
• Replace the battery pack or charger immediately if the battery
case or charger cord is damaged.
• Always make sure the grass trimmer switch is Off before
inserting or removing the battery pack.
• Always make sure the battery pack is removed and the switch
turned Off before replacing spools or adjusting the line.
• Read, understand, and follow the Battery Charger
• instructions.
model no. 060-2293-6 | contact us: 1 866 523 5218
ASSEMBLE ThE TWO hALVES Of ThE ShAfT
1. Insert the lower shaft(3) into upper shaft(2).
2. Then turn the upper shaft(2) until lock button clicks into
place.
3. Turn the lower shaft(3) collar until locked into place.
Auxiliary handle
1. Turn the handle lock knob (1) counter-clockwise
several turns to loosen the auxiliary handle
(2).
2. Adjust the handle position to provide the best
level of balance and control for the operator.
2
3. Securely lock the handle in position by turning
the knob clockwise.
4. Before operating the grass trimmer, make
1
sure the auxiliary handle is tightly locked into
position.
Cutting Line:
3
A spool of monofilament cutting line is preinstalled on the grass trimmer. When the cutting
line needs replacing, insert a new spool.
To remove the spool:
1
1. Disconnect trimmer from the power supply.
2. Turn grass trimmer over to access the spool.
3. Remove spool cover by pressing on two tabs parallel
2
to each other on the side of the cover (2).
4. Remove the spool (1) from the spool housing (3).
To replace the spool:
1. Replace the spool (1) with a new pre-wound spool.
2. Insert the end of line through the opening (4) in the spool housing (3).
3. Align the tabs on the spool cover with the slots in the spoo l housing on
the trimmer head.
4. Push down on the spool cover, locking it to the spool housing.
5. To advance the line when initially installed, you must pull the line while
pressing the black line release button on the side of the spool
housing (3).
!
WARNING! To avoid injury, adjust the auxiliary
handle for optimum control and balance. Do not
overreach when operating the grass trimmer. Keep
proper balance at all times for better control of the
tool in unexpected situations.
7
2
1
3
2
1
2
1
4
3