National Instruments NI sbRIO-960x User Manual
  1. Manuals
  2. Brands
  3. National Instruments Manuals
  4. Computer Hardware
  5. NI sbRIO-960x
  6. User manual
National Instruments NI sbRIO-960x User Manual

National Instruments NI sbRIO-960x User Manual

Single-board rio oem devices
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
USER GUIDE
NI sbRIO-960x
Single-Board RIO OEM Devices
National Instruments makes no product safety, electromagnetic compatibility
Caution
(EMC), or CE marking compliance claims for the sbRIO-960x. The end-product supplier
is responsible for conformity to any and all compliance requirements.
Caution
Exercise caution when placing the sbRIO-960x inside an enclosure. Auxiliary
cooling may be necessary to keep the device under the maximum ambient temperature
rating of 55 °C.
This document provides dimensions, pinouts, connectivity information,
and specifications for the National Instruments sbRIO-9601 and
sbRIO-9602. The devices are referred to inclusively in this document as
the sbRIO-960x.
The following figure shows the sbRIO-960x.
Figure 1. sbRIO-960x

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NI sbRIO-960x and is the answer not in the manual?

Questions and answers

Related Manuals for National Instruments NI sbRIO-960x

Summary of Contents for National Instruments NI sbRIO-960x

  • Page 1 NI sbRIO-960x Single-Board RIO OEM Devices This document provides dimensions, pinouts, connectivity information, and specifications for the National Instruments sbRIO-9601 and sbRIO-9602. The devices are referred to inclusively in this document as the sbRIO-960x. National Instruments makes no product safety, electromagnetic compatibility Caution (EMC), or CE marking compliance claims for the sbRIO-960x.

  • Page 2: What You Need To Get Started

    ❑ ❑ ❑ Hardware Requirements You need the following hardware to use the sbRIO device. ❑ ❑ ❑ NI sbRIO-960x and enter the info code ni.com/info LabVIEW LabVIEW Real-Time Module LabVIEW FPGA Module NI-RIO Software sbRIO-960x 19–30 VDC power supply...
  • Page 3 Resource tab for the sbRIO device you are using. Note The plated mounting holes are all connected to P1, the ground lug. Connect P1 or one of the plated mounting holes securely to earth ground. © National Instruments Corporation ni.com/singleboard and look on the NI sbRIO-960x...
  • Page 4 ABOVE THIS CAPACITOR .380 (9.65) .365 (9.28) .651 (16.54) .220 (5.59) .180 (4.57) .080 (2.03) .000 (0) NI sbRIO-960x Figure 2. sbRIO-960x Dimensions in Inches (Millimeters) 7X Ø .134 (3.4) 3.520 (89.41) .450 (11.43) 2X 4-40 THREADS .625 (15.88) .327 (8.31) .242 (6.16)
  • Page 5 To maintain isolation clearances on the C Series modules, do not use mounting Note hardware larger than 0.240 in. (6.1 mm) in diameter and maintain an air gap of at least 0.200 in. (5.0 mm) from the modules to anything else. © National Instruments Corporation 8X Ø .125 (3.18) NI sbRIO-960x...
  • Page 6 2 P5, 3.3 V Digital I/O 3 J10, Connector for C Series Module 4 P4, 3.3 V Digital I/O 5 J9, Connector for C Series Module NI sbRIO-960x 6 DIP Switches 7 Backup Battery 8 P2, 3.3 V Digital I/O...
  • Page 7 Serial Port high, with 4-40 jacksockets P2, P3, P4, P5 50-pin polarized header plug, 0.100 × 0.100 in. (2.54 × 2.54 mm) © National Instruments Corporation Table 1. sbRIO Connector Descriptions Description Part Number and Manufacturer 1727566 from Phoenix Contact;...
  • Page 8 The following figures show the pinouts of the I/O connectors on the sbRIO devices. Pin 50 NI sbRIO-960x D GND D GND D GND D GND D GND D GND D GND D GND D GND D GND D GND...
  • Page 9 Pin 50 © National Instruments Corporation D GND D GND D GND D GND D GND D GND D GND Pin 1 Port9/DIOCTL D GND D GND D GND D GND D GND D GND D GND D GND D GND...
  • Page 10 Pin 50 NI sbRIO-960x D GND D GND D GND D GND Port2/DIOCTL D GND D GND D GND D GND D GND D GND D GND D GND D GND Port1/DIOCTL D GND D GND D GND Pin 1...
  • Page 11 Pin 50 The following figure and table show the signals on J1, the RS-232 serial port. © National Instruments Corporation D GND D GND D GND D GND D GND D GND D GND Pin 1 Port4/DIOCTL D GND D GND...
  • Page 12 Refer to the Measurement & Automation Explorer Help for more information about configuring the device in Measurement & Automation Explorer (MAX). NI sbRIO-960x Table 2. RS-232 Serial Port Pin Descriptions Signal Cabling section for more ni.com...
  • Page 13 LabVIEW RT application each time it is booted. Refer to the Running a Stand-Alone Real-Time Application (RT Module) topic of the LabVIEW Help for more information. © National Instruments Corporation section of this document, but the actual power requirement Remove the MINI-COMBICON plug from connector J3 of the sbRIO-960x.

  • Page 14: Boot Options

    The system clock of the sbRIO device gets the date and time from the internal real-time clock at startup. This synchronization provides timestamp data to the device. NI sbRIO-960x Table 3. sbRIO Reset Options Does not load the FPGA bit stream from flash memory.

  • Page 15: Configuring Dip Switches

    1 SAFE MODE 2 CONSOLE OUT All of the DIP switches are in the OFF (up) position when the sbRIO device is shipped from National Instruments. SAFE MODE Switch The position of the SAFE MODE switch determines whether the embedded LabVIEW Real-Time engine launches at startup.
  • Page 16 If you already have an application configured to launch at startup and you push the NO FPGA switch from ON to OFF, the startup application is automatically enabled. NI sbRIO-960x One stop bit No flow control . If the device is on your local subnet and 0.0.0.0...

  • Page 17: User Led

    The STATUS LED is off during normal operation. The sbRIO device indicates specific error conditions by flashing the STATUS LED a certain number of times as shown in Table 4. © National Instruments Corporation Boot Options section for more information.
  • Page 18 IP address, subnet mask, DNS address, gateway, and Time Server IP are set to VIs are unaffected. Complete the following steps to restore the device to the factory network settings. NI sbRIO-960x Table 4. Status LED Indications Indication Configuring DIP Switches . Power-on defaults, watchdog settings, and 0.0.0.0...
  • Page 19 ESD events. The combination of R1 and D1 protects against overvoltage, and the combination of R1 and D2 protects against undervoltage. The resistance of R1 increases rapidly with temperature. © National Instruments Corporation +5 V Figure 12. Circuitry of One 3.3 V DIO Channel...

  • Page 20: Signal Integrity

    P2–P5. Each pin on the headers is rated for 2 A, but a typical 28 AWG ribbon cable is rated for only 225 mA per conductor. NI sbRIO-960x section for current-limiting and resistance values. ™...

  • Page 21: Specifications

    ... 400 MHz Memory Non-volatile memory System memory Xilinx Spartan 3 Reconfigurable FPGA Number of logic cells Available embedded RAM © National Instruments Corporation sbRIO-9601... 128 MB sbRIO-9602... 256 MB sbRIO-9601... 64 MB sbRIO-9602... 128 MB sbRIO-9601... 17,280 sbRIO-9602... 46,080 sbRIO-9601...
  • Page 22 Output logic levels Overvoltage protection at –20 to 70 °C ...±20 V (maximum 2 pins Posistor (PRG18BB330MS1RB from Murata) NI sbRIO-960x Input high voltage, V ...2.0 V min; 5.25 V max Input low voltage, V ...0 V min; 0.8 V max Output high voltage, V sourcing 3 mA ...2.7 V min;...
  • Page 23 Resistance-temperature characteristics, typical curve Resistance-Temperature Characteristics Graph-1 Typical Curve 1000 –40 –20 Temperature (°C) © National Instruments Corporation NI sbRIO-960x...

  • Page 24: Power Requirements

    Maximum P Maximum P The sbRIO device is 1–2% more efficient with a 19 V supply than with a 30 V supply. NI sbRIO-960x section for information about connecting the power supply. Total power requirement = P is the consumption by sbRIO internal operation is the consumption by the 3.3 V DIO...

  • Page 25: Environmental Management

    Caution Measurement Categories II, III, or IV. Environmental Management National Instruments is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial not only to the environment but also to NI customers.

  • Page 26: Physical Characteristics

    Waste Electrical and Electronic Equipment (WEEE) At the end of their life cycle, all products must be sent to a WEEE recycling EU Customers center. For more information about WEEE recycling centers and National Instruments WEEE initiatives, visit National Instruments...
  • Page 27 Cabling Table 5 shows the standard Ethernet cable wiring connections for both normal and crossover cables. Connector 1 Pin 1 © National Instruments Corporation Table 5. Ethernet Cable Wiring Connections Connector 1 white/orange white/orange orange orange white/green white/green blue blue...

  • Page 28: Where To Go For Support

    Instruments trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National Instruments products, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your media, or ni.com/patents.

Table of Contents