Table of Contents
Advertisement
Quick Links
Raystar 125 GPS Receiver
Owner's Handbook
Welcome to the Raystar RS125 GPS Receiver
What's in the box?....
Part No: R38103
Raystar RS125 GPS Receiver
Flush mount gasket
The Raystar RS125 GPS Receiver has no user serviceable parts.
What tools do I need to install it?....
Drill
Your handbook contains an explanation of how to install,
operate and maintain your Raystar RS125 GPS Receiver.
Intended Use
This product is a GPS antenna with a built-in position
fixing receiver using either NMEA0183 (Version 2.3 or
later), or Raymarine SeaTalk data output. The intended
application is for leisure marine boats and workboats not
covered by IMO/SOLAS carriage requirements.
Part No: E35018
Pole mount kit
6mm (
1
/
in)
4
Drill bit
10m (33ft) NMEA/SeaTalk
Thumb nuts (x2)
Studs (x2)
20mm (
13
/
in)
16
Drill bit
www.raymarine.com
Part No: R38104
connection cable
3- way
Scotchlok
connectors (x5)
Screws (x2)
Phillips
screwdriver
Adhesive tape
1
TM
Advertisement
Table of Contents
Related Manuals for Raymarine Raystar 125
Summary of Contents for Raymarine Raystar 125
-
Page 1: Intended Use
This product is a GPS antenna with a built-in position fixing receiver using either NMEA0183 (Version 2.3 or later), or Raymarine SeaTalk data output. The intended application is for leisure marine boats and workboats not covered by IMO/SOLAS carriage requirements. -
Page 2: Safety Notices
Safety notices RS125 GPS Receiver WARNING: Navigation aid Although this product has been designed to be accurate and reliable, many factors can affect its performance. As a result, it should only be used as an aid to navigation and should never replace common sense and navigational judgement. Always maintain a permanent watch so you can respond to situations as they develop. - Page 3 To mount the unit on a pole..Securely attach the pole mount base to a suitable pole. Pass the cable and connector through either the center of the pole mount bracket and the pole, or the cable exit hole alongside the center hole.
-
Page 4: To Connect To Nmea 0183
To connect the RS125 using Scotchlok connectors..RS125 GPS Receiver Using suitable wire clippers, remove the tinned ends from the individual cables. Leave the insulation intact. Place the wires to be joined into the connectors, ensuring correct polarity and that the wires are fully pushed home. - Page 5 To connect to the RS125 into a SeaTalk system..C-Series C-Series SeaTalk cable RS125 GPS Part No. R08050 Receiver cable Scotchlok connectors E-Series RS125 GPS E-Series SeaTalk cable Receiver cable Part No. E55054 To external alarm To connect to an E-Series display using SeaTalk..When connecting your RS125 into an existing SeaTalk network it should be powered from the network and not the display.
- Page 6 What do the lights mean?..RS125 GPS Receiver Flashing RED Unit is in bootcode, either being upgraded or unable to boot. Flashing ORANGE Unit is running, but does not have a fix. Flashing GREEN Unit is running and has a fix. 1 flash every 2 seconds indicates NMEA connection.
-
Page 7: Emc Conformance
For full details of their licensing agreement refer to our website at www.raymarine.com Warranty To register your new Raymarine product, please take a few minutes to fill out the warranty card. It is important that you complete the owner information and return the card to us to receive full warranty benefits. -
Page 8: Waste Electrical And Electronic Equipment Directive
The Waste Electrical and Electronic Equipment (WEEE) Directive requires the recycling of waste electrical and electronic equipment. Whilst the WEEE Directive does not apply to some of Raymarine's products, we support its policy and ask you to be aware of how to dispose of this product.
Need help?
Do you have a question about the Raystar 125 and is the answer not in the manual?
Questions and answers