Advertisement
JY997D29501F
GT10-LDR Memory loader
User's Manual
Manual Number
JY997D29501F
Date
April 2015
This manual describes the part names, dimensions, mounting, and specifications
of the product. Before use, read this manual and manuals of relevant products
fully to acquire proficiency in handling and operating the product. Make sure to
learn all the product information, safety information, and precautions.
And, store this manual in a safe place so that you can take it out and read it
whenever necessary. Always forward it to the end user.
Registration
The company name and the product name to be described in this manual are the
registered trademarks or trademarks of each company.
Effective April 2015
Specifications are subject to change without notice.
2007 MITSUBISHI ELECTRIC CORPORATION
Safety Precaution
(Read these precautions before using.)
Before using this product, please read this manual and the relevant manuals
introduced in this manual carefully and pay full attention to safety to handle the
product correctly.
The precautions given in this manual are concerned with this product.
In this manual, the safety precautions are ranked as "WARNING" and
"CAUTION".
Indicates that incorrect handling may cause hazardous
conditions, resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous
conditions, resulting in medium or slight personal injury
or physical damage.
Depending on circumstances, procedures indicated by "CAUTION" may also be
linked to serious results.
In any case, it is important to follow the directions for usage.
MOUNTING PRECAUTIONS
Use the memory loader in the environment that satisfies the general
specifications described in GT10 User's manual. Never use the product in
areas with excessive dust, oily smoke, conductive dusts, corrosive gas (salt
air, Cl
, H
S, SO
or NO
), flammable gas, vibration or impacts, or exposed
2
2
2
2
to high temperature, condensation, or rain and wind. Not doing so can cause
an electric shock, fire, malfunction or product damage or deterioration.
STARTUP/MAINTENANCE
PRECAUTIONS
Do not disassemble or modify the memory loader.
Doing so can cause a failure, malfunction, injury or fire.
Do not touch the conductive and electronic parts of the memory loader
directly. Doing so can cause a memory loader malfunction or failure.
When unplugging the cable connected to the GOT, do not hold and pull the
cable portion. Doing so can cause the memory loader or cable to be
damaged or can cause a malfunction due to a cable connection fault.
Do not bent at a sharp angle or tie the memory loader cables.
Doing so can cause the breaking of the cables.
DISPOSAL PRECAUTIONS
When disposing of the product, handle it as industrial waste.
TRANSPORTATION
PRECAUTIONS
Make sure to transport the memory loader and/or relevant unit(s) in the
manner they will not be exposed to the impact exceeding the impact
resistance described in the general specifications of this manual, as they are
precision devices. Failure to do so may cause the unit to fail.
2.3 Communication Specifications
Item
Specifications
Conforming to RS232
GOT communication
Transmission speed :115,200bps
Connector shape
: MINI DIN 6Pins (Male)
Conforms to USB2.0 (Full speed is supported.)
(Performs the conversion between USB and serial in
PC communication
GT10-LDR. After serial conversion, transmission
speed is 115.200bps.)
Connector shape
:USB MINI-B 5Pins (Receptacle)
3. External Dimensions
External Dimensions
14
70 (2.75")
(0.55")
Unit: mm (inch)
Weight: 0.2kg
4. Part Name
1)
2)
3)
4)
5)
7)
8)
No.
Name
1)
POWER LED
LED to show power status
2)
SET/RUN LED
LED to show that the settings are being checked/the transfer is running
3)
ERROR LED
LED to show error status
4)
RD/WR selection switch
Switch to select read/write direction
5)
Data selection switch
Switch to select the data to be transferred
6)
ENT key
Switch to determine the transfer direction and the data to be transferred, and to start the transfer
Compliance with EC directive (CE Marking)
This note does not guarantee that an entire mechanical module produced in
accordance with the contents of this note will comply with the following standards.
Compliance to EMC directive for the entire mechanical module should be checked by
the user / manufacturer. For more details please contact the local Mitsubishi Electric
sales site.
Attention
This product is designed for use in industrial applications.
Authorized Representative in the European Community:
Mitsubishi Electric Europe B.V.
Gothaer Str. 8, 40880 Ratingen, Germany
Requirement for Compliance with EMC directive
The following products have shown compliance through direct testing (to the identified
standards) and design analysis (forming a technical construction file) to the European
Directive for Electromagnetic Compatibility (2004/108/EC) when used as directed by
the appropriate documentation.
Type :Programmable Controller (Open Type Equipment)
Standard
Compliance with all relevant aspects of the
EMI
standard. (Radiated Emissions)
EN61131-2 : 2007
Programmable
Compliance with all relevant aspects of the
controllers-
standard.
Equipment,
EMS
(ESD, RF electromagnetic field, EFTB, Surge, RF
requirement and tests
conducted disturbances and Power frequency
magnetic field)
For more details please contact the local Mitsubishi Electric sales site.
Associated Manuals
The following manuals are relevant to this product. When these loose manuals are
required, please consult with our local distributor.
Manual name
Contents
Describes the GT10 hardware-relevant
content such as part names, external
dimensions, mounting, power supply
GT10 User's Manual
wiring, specifications, and introduction to
option devices.
(sold separately)
GT Designer2
Describes methods of the GT Designer2
Version2 Basic
installation operation, basic operation for
Operation/Data
drawing and transmitting data to
Transfer Manual
GOT1000 series
(For GOT1000 Series)
(sold separately)
GT Designer3
Describes methods of the GT Designer3
Version1 Screen
installation operation, basic operation for
Design Manual
drawing and transmitting data to
(For GOT1000 Series)
GOT1000 series
(Fundamentals)
(sold separately)
Bundled Items
Bundled item
GT10-LDR memory loader
USB cable (1m)
GT10-LDR Memory loader USER'S MANUAL (This manual)
2.4 Power Supply Specifications
Item
Specifications
DC5V (DC4.75 to 5.25V)
Input power supply voltage
Supplied from the GOT or PC (Supplied from bus
power)
Fuse
Power consumption
0.7W (140mA/DC5V) or less
Cable length
240 (9.44 ")
12)
13)
6)
9)
Specifications
1. Overview
GT10-LDR memory loader is the memory transfer module that reads/writes the data to GT10 or between a PC (GT Designer2 Ver.2.77F or later, GT Designer3 Ver.1.01B or
later) and GT10-LDR.
*1 When GT10-LDR is connected to a PC via the USB hub, the power supply of the USB hub must be supplied by the AC adopter of the USB hub.
GT10-LDR connected to the USB hub may not work properly depending on the PC environment. In the case, connect the GT10-LDR directly to the USB port on the PC.
Remark
2. Specifications
2.1 General Specifications
Item
Operating ambient temperature
Storage ambient temperature
*1
Operating ambient humidity
*1
Storage ambient humidity
Manual
Number
Vibration resistance
(Model Code)
JY997D24701
Shock resistance
(09R819)
Operating atmosphere
*2
Operating altitude
SH-080529ENG
(1D7M24)
Overvoltage category
*3
Pollution degree
*4
Cooling method
SH-080866ENG
(1D7MB9)
*1 The wet bulb temperature is 39C or less.
*2 Do not use or store the GOT under pressure higher than the atmospheric pressure of altitude 0m (0ft.). Failure to observe this instruction may cause a malfunction.
When the air inside the control panel is purged by pressurization, the surface sheet may be lifted by high pressure. As a result, the touch panel may be difficult to press,
and the sheet may be peeled off.
*3 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the
machinery within the premises.
Category II applies to equipment for which electrical power is supplied from fixed facilities.
The surge voltage withstand level for up to the raged voltage of 300 V is 2500 V.
Quantity
*4 This index indicates the degree to which conductive material is generated in the environment where the equipment is used.
1
In pollution degree 2, only non-conductive pollution occurs but temporary conductivity may be produced due to condensation.
1
2.2 Performance Specifications
1
Item
User memory
*1
Memory
Life (Number of write
times)
POWER
LED
SET/RUN
ERROR
No.
Name
7)
Write protection switch
8)
USB port
9)
Reference plate (operating instructions)
-
10)
Reference plate (error contents)
11)
Transfer cable
12)
Strap hole
13)
Part to be labeled
14)
Rating plate (Nameplate)
5. LED lighting specification
LED Name
Status
POWER LED is lit.
POWER
POWER LED is not lit.
POWER LED is not lit.
Orange light
SET/RUN
Green flashing
Green light
Red flashing
Unit: mm (inch)
POWER LED is not lit.
Green light*
Green flashing*
1
ERROR
Red light*
Red flashing*
Red
Green*
Orange
Green*
*1 An error message appears on the GOT screen. Apply remedies according to the display.
Refer to the "Chapter 12 Troubleshooting" for details on handling errors.
6. Switch operation specification
10)
Switch Name
Switch to select read/write direction
RD/WR selection
11)
RD : The data is read out from the GOT to the memory loader.
switch
WR : The data is written from the memory loader to the GOT.
Switch to select the data to be transferred
When reading out the data from the GOT to the memory loader
[PROJECT + OS] : The standard monitor OS, communication driver, project data, and resource data are read out from the GOT to the memory
loader.
14)
Data selection switch
[PROJECT] : The project data and resource data are read out from the GOT to the memory loader.
When writing the data from the memory loader to the GOT
[PROJECT + OS] : The standard monitor OS, font data, communication driver, and project data are written from the memory loader to the GOT.
[PROJECT] : The project data is written from the memory loader to the GOT.
Switch to prevent the memory loader from being written to the data
Write protection switch
ON : The data cannot be written neither from the GOT or a PC (GT Designer2, GT Designer3) to the memory loader.
OFF : The data can be written from the GOT or a PC (GT Designer2, GT Designer3) to the memory loader.
Switch to determine the transfer direction and the data to be transferred, and to start the transfer
The transfer starts by pressing the key twice.
The first pressing of the key determines the read/write direction and the data to be transferred.
(After the read/write direction and the data to be transferred are determined, if RD/WR selection switch and Data selection switch are operated,
ENT key
the operations that have been made will be canceled.)
(The ENT key must be pressed within 30 seconds after the first pressing of the ENT key. Failure to do so cancels the operations that have been
made.)
The second pressing of the key starts the transfer.
*1 When the standard monitor OS and communication driver are transferred from the memory loader to the GOT, starting up the GOT with OS installation screen is
required.
GT1020, GT1030
USB connecting
cable (supplied)
PC
*1
(GT Designer2 Ver.2.77F or later
GT Designer3 Ver.1.01B or later)
Specifications
0 to 40C
-20 to 60C
10 to 90% RH, non-condensing
10 to 90% RH, non-condensing
Frequency
5 to 9Hz
Under intermittent
Conforms to JIS
vibration
B3502 and
9 to 150Hz
IEC61131-2
5 to 9Hz
Under continuous
vibration
9 to 150Hz
Conforms to JIS B3502, IEC 61131-2 (147 m/s
2
, 3 times each in X, Y and Z directions)
Must be free of lamp black, corrosive gas, flammable gas, or excessive amount of electro conductive dust particles and must be no
direct sunlight. (Same as for saving)
2000 m (6562 ft) max.
II or less
2 or less
Self-cooling
Specifications
Flash ROM 7.5Mbyte
100,000 times
green
Switch
green/red/orange
green/red/orange
External dimensions
Weight
*1 ROM in which new data can be written without deleting the written data.
Switch to prevent the memory loader from being written to the data
Connection port with a PC (with protection cap)
Described operating instructions of the memory loader
Described lighting status of ERROR LED
Cable to be connected with the GOT
A hole to attach a strap
Space to be labeled (created by user)
Power is supplied.
Power is not supplied.
Before starting the transfer.
The transfer direction and the data to be transferred are determined.
The transfer is running.
The transfer is completed.
The transfer is aborted.
No errors
1
Write protection switch ON
1
The GOT type that is set in the data to be transferred differs from that of the GOT to which the data is transferred.
The data to be transferred is broken.
The major version of the standard monitor OS is different from that of the project data.
1
Communication error occurs between the GOT and the memory loader.
1
Password is set in the project data.
1
OS installation screen is not active
Specifications
Acceleration
Half-amplitude
Sweep Count
--
3.5mm
9.8m/s
2
--
10 times each in X, Y
and Z directions
--
1.75mm
4.9m/s
2
--
Item
Specifications
RD/WR selection
switch
Paddle switch
Data selection switch
Tactile switch
The use of 100 thousand times is due for
ENT key
replacement.
(operating force 2.55N
0.69N)
Write protection switch
Slide switch
W70(2.75)H110(4.33)D21(0.82)[mm](inch)
0.2kg
Specifications
--
Contents
Advertisement
