Table of Contents
Advertisement
OWNER'S MANUAL AND OPERATING INSTRUCTIONS
7 Ton
LOG SPLITTER
MODEL NUMBER
90720
10006 Santa Fe Springs Road
SAVE THESE INSTRUCTIONS
Santa Fe Springs CA 90670
Important Safety Instructions
USA / 1-877-338-0999
MADE IN CHINA
are included in this manual.
REV 90720-20130226
www.championpowerequipment.com
Advertisement
Table of Contents
Related Manuals for Champion Power Equipment 90720
Summary of Contents for Champion Power Equipment 90720
- Page 1 OWNER’S MANUAL AND OPERATING INSTRUCTIONS 7 Ton LOG SPLITTER MODEL NUMBER 90720 10006 Santa Fe Springs Road SAVE THESE INSTRUCTIONS Santa Fe Springs CA 90670 Important Safety Instructions USA / 1-877-338-0999 MADE IN CHINA are included in this manual. REV 90720-20130226 www.championpowerequipment.com...
- Page 2 AN IMPORTANT MESSAGE ABOUT TEMPERATURE: Your Champion Power Equipment product is designed and rated for continuous operation at ambient temperatures up to 40°C (104°F). When your product is needed your product may be operated at temperatures ranging from -15°C (5°F) to 50°C (122°F) for short periods.
-
Page 3: Table Of Contents
90720 7 Ton LOG SPLITTER TABLE OF CONTENTS Cleaning ......Introduction ......1 Maintenance Schedule . -
Page 4: Introduction
Introduction Accessories Congratulations on your purchase of a Champion Champion Power Equipment manufactures and sells Power Equipment log splitter. CPE designs and builds accessories designed to help you get the most from your log splitters to strict specifications. With proper use purchase. -
Page 5: Manual Conventions
Please call our help line at 1-877-338-0999 situation which, if not avoided, could result in death or serious injury. CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. REV 90720-20130226... -
Page 6: Safety Rules
Keep work zone clear of debris while working to can start fires around dry vegetation. ensure safe footing. A spark arrestor may be required. The operator should contact local fire agencies for laws or regulations relating to fire prevention requirements. REV 90720-20130226... - Page 7 DO NOT expose log splitter to excessive moisture, dust, or dirt. DO NOT allow any material to block the cooling slots. DO NOT use the engine if: – Equipment sparks, smokes or emits flames – Equipment vibrates excessively REV 90720-20130226...
-
Page 8: Training
Make sure you comply with local, state, and federal codes. Take appropriate fire-fighting equipment with you. 10. Log splitters should be used only for splitting wood. Do not use for other purposes unless the manufacturer provides attachments and instructions. REV 90720-20130226... -
Page 9: Operation
12. Use only your hand to operate the log splitter controls. 13. Do not refuel the engine until it has cooled for several minutes. REV 90720-20130226... -
Page 10: Controls And Features
Hydraulic Cylinder – Converts hydraulic pressure (11) Support Leg – Supports log splitter while into linear force. operating. Hydraulic Oil Dipstick (12) Hydraulic Pump – Pumps hydraulic oil through the system. REV 90720-20130226... -
Page 11: Assembly
3. Place a washer and lock washer on the end of the bolt. 4. Install the nut on the bolt and tighten. Do not over tighten. NOTE The recoil side of the engine should point the same direction as the beam as shown. REV 90720-20130226... -
Page 12: Install The Cylinder To The Beam
¼ turn past finger tight. 3. Secure the bolt with M10 lock nut (#1). Do not over tighten. NOTE A screwdriver can be inserted into the cylinder rod’s bolt hole to rotate to proper position prior to installing the ram bracket. REV 90720-20130226... -
Page 13: Add Engine Oil
30 days. Pouring fuel too fast through the fuel screen may result in blow back of fuel at the operator while filling. REV 90720-20130226... -
Page 14: Add Engine Fuel
Remove and read level. Do not thread dipstick into fill neck when checking oil. NOTE Failure to open the hydraulic vent screw will cause pressure build-up due to heat. This creates difficulty during maintenance and operation. REV 90720-20130226... -
Page 15: Operation
DO NOT work on mud, ice, tall grass, DO NOT let the beam drop as it could crush fingers brush or snow. or cause damage to the log splitter. Only operate log splitter from work zone shown below. REV 90720-20130226... -
Page 16: Starting The Engine
Log Splitter Operation 1. ALWAYS wear ear and eye protection, protective clothing and safety gear. 2. Block tires and ensure support leg is secure to prevent unintended movement of the log splitter during operation. REV 90720-20130226... - Page 17 If log sticks on wedge, load another piece of wood and extend ram to push the stuck piece off the wedge. NOTE The cylinder stroke is designed so the wedge stops approximately 1.5 in. (3.81 cm) from the end plate. REV 90720-20130226...
-
Page 18: Maintenance And Storage
Inspect all air vents and cooling slots to ensure that they are clean and unobstructed. Clean spark arrester every 100 hours (if equipped). Check and tighten all bolts and nuts before operating the log splitter. REV 90720-20130226... -
Page 19: Cleaning
Clean fuel tank and filter* Change hydraulic oil Every year Inspect wheel bearings and repack bearing grease as needed. Every 3 years Replace fuel line *To be performed by knowledgeable, experienced owners or Champion Power Equipment certified dealers. REV 90720-20130226... -
Page 20: Storage
DO NOT store a log splitter near fertilizer or any corrosive material. Even with an empty gas tank, gasoline vapors could ignite. REV 90720-20130226... -
Page 21: Specifications
(0.028 - 0.031 in.). An Important Message About Temperature Maintenance Valve Clearance Your Champion Power Equipment product is designed and rated for continuous operation at ambient – Intake: 0.13 – 0.17 mm (0.005 – 0.007 in.) temperatures up to 40°C (104°F). When your product is –... -
Page 22: Parts Diagram
90720 ENGLISH SPECIFICATIONS Parts diagram 25 26 27 47 54 55 51 26 27 27 26 25 36 26 27 38 39 REV 90720-20130226... -
Page 23: Parts List
Bolt M10×20 PMJ22G-27 Gear Pump Stand GB/T 5780-2000 Bolt M8×25 PMJ22G-26 Gear Pump Connector GB/T 41-2000 Nut M8 GB/T 93-1987 Lock washer 4 GB/T 93-1987 Lock washer 8 GB/T848-1985 Washer 4 GB/T 95-2000 Washer 8 PMJ7-04 Support Leg REV 90720-20130226... -
Page 24: Engine Parts Diagram
90720 ENGLISH SPECIFICATIONS Engine Parts diagram REV 90720-20130226... -
Page 25: Engine Parts List
Pipe, Fuel (Ø4.5×Ø8.5×95) 48 2.15.005 (E6RTC) Spark Plug (E6RTC) 101 12.070400.00 Fuel Valve 49 1.5789.0855 Flange Bolt M8×55 102 5.1010.002.3 Flameout Switch 50 12.020002.00 Gasket, Cylinder Head Cover 103 2.06.004 Clamp(Ø10.5×Ø1) 51 12.021100.01 Cylinder Head Cover 52 12.020007.00 Baffle, Line REV 90720-20130226... -
Page 26: Troubleshooting
Faulty control valve Contact Customer Service Excessive bouncing while towing Under-inflated tires Inflate tires to proper pressure. Refer to tire sidewall For further technical support: Technical Service Mon – Fri 8:30 AM – 5:00 PM (PST/PDT) Toll Free: 1-877-338-0999 tech@championpowerequipment.com REV 90720-20130226... -
Page 27: Warranty
Warranty Qualifications – Accessory parts such as starting batteries, and storage covers. Champion Power Equipment (CPE) will register this – Failures to due acts of God and other force majeure warranty upon receipt of your Warranty Registration Card events beyond the manufacturer’s control. - Page 28 The United States Environment Protection Agency (U.S. EPA.) and the California Air Resources Board (CARB) Emission Control System Warranty Your Champion Power Equipment (CPE) engine complies with both the U.S. EPA and state of California Air Resources Board (CARB) emission regulations.
- Page 29 EMISSION CONTROL SYSTEM WARRANTY The following are specific provisions relative to your Emission Control System (ECS) Warranty Coverage. 1. APPLICABILITY: This warranty shall apply to 1995 and later model year California small off-road engines (for other states, 1997 and later model year engines). The ECS Warranty Period shall begin on the date the new engine or equipment is delivered to its original, end-use purchaser, and shall continue for 24 consecutive months thereafter.
- Page 30 You must take your CPE engine or the product on which it is installed, along with your warranty registration card or other proof of original purchase date, at your expense, to any Champion Power Equipment dealer who is authorized by Champion Power Equipment, Inc. to sell and service that CPE product during his normal business hours.
Need help?
Do you have a question about the 90720 and is the answer not in the manual?
Questions and answers