Download
Share
Print this page
Contura C 650 Installation Instruction
  1. Manuals
  2. Brands
  3. Contura Manuals
  4. Indoor Fireplace
  5. 650
  6. Installation instruction

Contura C 650 Installation Instruction

Hide thumbs Also See for C 650:

Advertisement

Quick Links

Installation
instruction
C 650
www.contura.eu

Advertisement

loading
Need help?

Need help?

Do you have a question about the C 650 and is the answer not in the manual?

Questions and answers

Related Manuals for Contura C 650

Summary of Contents for Contura C 650

  • Page 1 Installation instruction C 650 www.contura.eu...
  • Page 2 See rating plate on the stove Intended area of use Heating of rooms in residential buildings Fuel Wood MANUFACTURER Name NIBE AB / Contura Address Box 134, Skulptörvägen 10 SE-285 23 Markaryd, Sweden CHECKS According to AVCP System 3 European standard...

  • Page 3: Table Of Contents

    A warm welcome to the Contura family. We hope you will get a great deal of pleasure from your new stove. As a new owner of a Contura stove, you have secured a product with timeless design and long service life.

  • Page 4: Technical Details

    FACTS Important to remember! Technical details Installation by authorised Structural support Effect 3-9 kW Nominal effect 6 kW technician Check that the wood joists are strong Efficiency up to 80% enough to bear the weight of the stove and This manual contains instructions about chimney.
  • Page 5 REMOVAL How to remove the hearth surround (Vermiculite) Handle the vermiculite with care. Lift the smoke baffle with one hand whilst removing the sides pieces. If necessary, move the cast-iron firebed slightly. Reinstall in reverse order The heat reflecting plate must be fitted underneath the body of the stove if the area below is to be used as a log-box.

  • Page 6: Connection To Chimney

    CHIMNEY Connection to chimney • The stove meets the requirements for connecting to chimneys • A flue with sharp bends and horizontal routing reduces the dimensioned for 350°C flue gas temperature. draught in the chimney. The maximum horizontal flue is 1 m, on the condition that the vertical flue length is at least 5 m.

  • Page 7: Supply Of Combustion Air

    SUPPLY AIR/ACCESSORY Supply of combustion air When a stove is installed in a room, the demand for air supply to the room increases. Air can be provided indirectly via a vent in the outer wall or via a duct from the outside that is connected to the connector on the underneath of the stove.

  • Page 8: Installation Distances

    INSTALLATION DISTANCES Installation distances C 650 The minimum distance in front of WHEN INSTALLING TURNTABLE (OPTION) the the stove opening to combustible following installation distances do not apply. parts of the building or interior See the separate turntable installation instruc- Combustible roof decoration must be at least 1 m.

  • Page 9: Assembly

    ASSEMBLY Installing C 650...
  • Page 10 ASSEMBLY Hold the side panel approximately 20 mm above the base panel and turn the side panel’s front edge around the edge of the leg. Align and depress the side panel end over the base panel’s shaft pin.
  • Page 11 ASSEMBLY Use starhead screws with washers to secure the side panels. Adjust the side panels so that they are against the insert at the front edge and the back plate at the rear edge. Install the metal shelf, soapstone shelf or baking oven according to the instructions in the section for the relevant accessory on pages 76 to 78.

  • Page 12: Installation Of Oven (Option)

    ASSEMBLY Installation of oven (option) Hold the oven door in place on the threaded pin. Hook the top hinge in place and loosely tighten one of the screws. Close the oven door and adjust it so that it aligns horizontally. Then open it carefully and tighten both screws.

  • Page 13: Installation Of Metal Warming Shelf (Option)

    ASSEMBLY Installation of metal warming shelf (option) Replace the preinstalled adjuster screw in the heating compartment with the longer adjuster screws provided. Place the warming shelf in the heating compartment, use the adjuster screw at the rear edge for horizontal installation. In the side of the heating compartment there is a small gap, this is used to install the rear cover panel.

  • Page 14: Installation Of Soapstone Warming Shelf (Option)

    ASSEMBLY Installation of soapstone warming shelf (option) Place the bottom plate for the warming shelf in the heating compartment, use the adjuster screw at the rear edge for level horizontal installation. Place paper from the packaging as scratch protection because the upper section must be slid into position.
  • Page 15 ASSEMBLY Installation of drawer (option) When installing the drawer, the knockout in the back panel must always be removed for the supply of convection air. Slacken off the rear Allen screws three turns. Place the pull-out unit on the base plate. Hook the pull-out unit into place over the rear Allen Install the drawer on the pull-out unit using the four screws.
  • Page 16 NIBE AB · Box 134 · 285 23 Markaryd · Sweden www.contura.eu Contura reserves the right to change colours, materials, dimensions and models at any time without special notice. 811111 IAV SE-EX C650 - 3 Your dealer can give you the most up to date information.

This manual is also suitable for:

C 655aC 655