Pulse Performance Products EM-1000 Owner's Manual
  1. Manuals
  2. Brands
  3. Pulse Performance Products Manuals
  4. Scooter
  5. EM-1000
  6. Owner's manual

Pulse Performance Products EM-1000 Owner's Manual

Hide thumbs

Advertisement

Table of Contents

ELECTRIC MOTORBIKE
OWNER'S MANUAL
FOR USE WITH THE FOLLOWING PULSE PERFORMANCE PRODUCTS™
•
EM-1000
DO NOT RETURN TO STORE! QUESTIONS OR COMMENTS?
CALL (866)-434-6067
NOTE: Manual illustrations are for reference purposes only. Illustrations may not reflect the exact appearance of the actual product.
Specifications are subject to change without notice.
7.9.15

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EM-1000 and is the answer not in the manual?

Questions and answers

Related Manuals for Pulse Performance Products EM-1000

Summary of Contents for Pulse Performance Products EM-1000

  • Page 1 ELECTRIC MOTORBIKE OWNER’S MANUAL FOR USE WITH THE FOLLOWING PULSE PERFORMANCE PRODUCTS™ • EM-1000 DO NOT RETURN TO STORE! QUESTIONS OR COMMENTS? CALL (866)-434-6067 NOTE: Manual illustrations are for reference purposes only. Illustrations may not reflect the exact appearance of the actual product.

  • Page 2: Table Of Contents

    Pulse Performance Products™ advises that you periodically review and reinforce all information in this manual with all riders, and that you inspect and maintain your motorbike to insure their safety.

  • Page 3: Safety And Warnings

    Safety and Warnings Maintain a hold with both hands on the handlebars at all times. Never allow more than one person at a time to ride the motorbike. Never use near steps, water, or swimming pools. Keep your fingers and other body parts away from the chain, motor, steering system, wheels and all other moving components. Never ride while using a cell phone or wearing headphones.

  • Page 4: Before You Start

    PULSE PERFORMANCE PRODUCTS™ ELECTRIC MOTORBIKE. This motorbike has been built to specific Pulse Performance Products™ design specifications and should not be modified. Altering of the original components may or may not be compatible with the design and will void the warranty.

  • Page 5: Assembly

    Assembly Handlebar Assembly Number Plate Assembly Tools required: 6mm hex wrench Tools required: Phillips Screwdriver 1. Align handlebars vertically and horizontally 1. Align the number plate with the holes in onto clamps (A&B). Install the 4 clamp bolts the fork and install the screws with a Phillips (C) and washers;...
  • Page 6 Assembly Front Wheel Assembly Tools required: 13mm wrench, 15mm wrench 1. Install front axle and hardware through 2. Ensure that safety washer tabs are front wheel. inserted into fork leg hole and tighten axle hardware securely with a 13mm and 15mm wrench.

  • Page 7: Assembly

    Assembly Charging the Battery WARNING: Battery must be fully charged before you ride your electric motorbike. Required components: battery charger • Initial battery charge time - 14 hours • Recharges after initial charge - up to 10 hours • When motorbike is not in regular use batteries need to be charged on a monthly basis to maximize performance 1.

  • Page 8: Hardware Maintenance

    Hardware Maintenance Brake Check the brakes for proper function. When you squeeze the lever, the brake should provide positive braking action. When you apply the brake with the throttle engaged, the brake cut off switch should stop the motor. Make sure that the brakes are not rubbing when the lever is not being applied. Frame, Fork and Handlebars Check for cracks or broken connections.

  • Page 9: Repair And Maintenance

    Repair and Maintenance WARNING: Turn the power switch “OFF” before conducting any maintenance procedures. Adjusting the Brakes Tools required: 10mm wrench Loosen Tighten 1. To adjust the brake cable thread clockwise 2. If the brake cable is still either too tight or (loosen) or counter clockwise (tighten) too loose use a 10mm wrench to loosen the the adjuster barrel on the brake lever.
  • Page 10 Repair and Maintenance WARNING: Turn the power switch “OFF” before conducting any maintenance procedures. Rear Wheel Removal/Replacement Tools required: Phillips Screwdriver, 8mm wrench, 10mm wrench, 15mm wrench 1. Using a Phillips screwdriver, remove the 2. Loosen brake cable pinch nut with a 3.
  • Page 11 Repair and Maintenance WARNING: Turn the power switch “OFF” before conducting any maintenance procedures. Rear Wheel Removal/Replacement (continued) Tools required: Phillips Screwdriver, 8mm wrench, 10mm wrench, 15mm wrench 6. Place chain onto chain wheel gear and 7. Align and tighten brake arm bolt with a 8.
  • Page 12 Repair and Maintenance WARNING: Turn the power switch “OFF” before conducting any maintenance procedures. Front Wheel Removal/Replacement Tools required: 13mm wrench, 15mm wrench 1. Loosen axle with 13mm and 15mm 2. Install front axle and hardware through 3. Ensure that safety washer tabs are wrenches and remove wheel from fork.
  • Page 13 Repair and Maintenance Battery Care and Disposal Do not store the battery in temperatures above 70°F (21°C) or below 32°F (0°C). THIS MOTORBIKE CONTAINS SEALED LEAD ACID BATTERIES WHICH MUST BE RECYCLED IN ACCORDANCE TO YOUR LOCAL AND STATE LAWS. PLEASE CAREFULLY READ AND UNDERSTAND THE FOLLOWING DISPOSAL INSTRUCTIONS: Disposal: This product contains sealed lead acid batteries which must be disposed or recycled in an environmentally safe manner.

  • Page 14: Repair And Maintenance

    Repair and Maintenance Battery Charger Only use the supplied battery charger. If battery charger is damaged discontinue use immediately and replace with a Pulse Performance Products™ electric motorbike recommended battery charger. Wheels Wheels and drive system components are subject to normal wear and tear. It is the responsibility of the user to regularly inspect wheels for excess wear and adjust and replace drive train components as required.

  • Page 15: Troubleshooting

    Troubleshooting Problem Possible Cause Solution Motorbike will not run. Battery is not charged. Fully charge the battery. First charge should be 14 hours and up to 10 hours for recharges. Wires or connectors are Check to ensure that charger is tightly plugged into both the wall loose or unplugged.

  • Page 16: Motorbike Components

    Motorbike Components part description part description part description Front Wheel Chain Upper-left Side Cover Front Wheel Axle Chain Disc Upper-right Side Cover Fender Rear Wheel Motor Number Plate Tensioner Drum Right Side Cover Frame Drum Brake Controller Lower Chain Cover Rear Plastic Cover Battery Box Right Side Cover Battery Press Plate...

  • Page 17: Warranty

    The manufacturer is not liable for incidental or consequential loss or damage due directly or indirectly to the use of this product. Pulse Performance Products™ does not offer an extended warranty. If you have purchased an extended warranty, it must be honored by the store at which the motorbike was purchased from.
  • Page 18 Pulse Performance Products™ A Division of Bravo Sports™ 12801 Carmenita Rd. Santa Fe Springs, CA 90670 © 2015 - 2016 Pulse Performance Products™ - All Rights Reserved...

Table of Contents

Save PDF