Table of Contents
Advertisement
FULL DEPTH HE GAS FIRE
USER INSTRUCTIONS
INSTALLATION INSTRUCTIONS
SERVICE INSTRUCTIONS
It is a regulation that these instructions be handed to the customer after installation is complete. It is
also the responsibility of the installation engineer to ensure that the customer is able to fully operate
the appliance and is aware of any cleaning or maintenance requirements.
Model numbers: BM-05XXX1 MANUAL for use on Natural Gas (G20) at a supply pressure of 20 mbar in GB / I.E.
Model numbers: BM-05XXX2 SLIDE for use on Natural Gas (G20) at a supply pressure of 20 mbar in GB / I.E.
(XXX denotes Fret Type, Fuel Bed Type & Trim Type)
P-XX1541 ISSUE1
Advertisement
Table of Contents
Related Manuals for Be Modern BM-05XXX1
Summary of Contents for Be Modern BM-05XXX1
-
Page 1: Installation Instructions
Model numbers: BM-05XXX1 MANUAL for use on Natural Gas (G20) at a supply pressure of 20 mbar in GB / I.E. Model numbers: BM-05XXX2 SLIDE for use on Natural Gas (G20) at a supply pressure of 20 mbar in GB / I.E. -
Page 2: Table Of Contents
CONTENTS Regulatory Information and Installation Requirements …………………………... 3 Installation Requirements (continued) ………………………………………………….. 4 Siting the Appliance ……………………………………………………………………………… 5 Front glass removal and replacement ……………………………………………………. 8 Fixing the Appliance ...………………………………………………………………………...… 7 Connecting the Appliance to the Gas Supply ……………………………………….. 9 Checking Operation of Appliance ………………………………………………………… 9 Completing the Installation ……………………………………………………………………... -
Page 3: Regulatory Information And Installation Requirements
REGULATORY INFORMATION AND INSTALLATION REQUIREMENTS THE FOLLOWING MUST BE NOTED PRIOR TO THE INSTALLATION OF THIS APPLIANCE. This gas appliance MUST be installed by a GAS SAFE registered installer by law. It must be installed in accordance to these installation instructions and the GAS SAFETY (Installation & Use) REGULATIONS 1998 as amended. -
Page 4: Installation Requirements (Continued)
No purpose made ventilation is normally required for this appliance when installed in G.B. If the appliance is being installed in I.E then refer to I.S 813:1996 (Domestic Gas Installation—National Standards Authority of Ireland). Ventilation areas (if applicable) should be checked periodically to ensure there is no obstruction, even though none is normally required for this appliance. -
Page 5: Siting The Appliance
The installation of this appliance into an unsuitable back panel, where this component subsequently cracks, will not be deemed to be a fault of the appliance. This appliance is suitable for Be Modern installation into a approved back-panel where it is NOT installed as a closure plate (i.e. - Page 6 In addition it is imperative that ONLY fascia/trim arrangements supplied by Be Modern deemed suitable to be used with Be Modern appliances in a ‘hole in the wall’ installation shall be used.
-
Page 7: Fixing The Appliance
If the spillage monitoring device (O.D.S pilot) is replaced it must only be exchanged with a suitable component which is supplied by Be Modern Ltd. -
Page 8: Front Glass Removal And Replacement
Removal of the front glass panel. The top glass clamp is held in place with 3 screws. This panel is concealed behind the top cover strip which is held in place by two magnets. The two magnets are fitted to the top glass clamp as shown in this diagram. -
Page 9: Connecting The Appliance To The Gas Supply
Connecting the Appliance to the Gas Supply The gas supply can be connected to the appliance by a concealed fitting from the rear. In all installation conditions the gas connection should be provided using 8mm (O/D) copper tubing. If the concealed installation method is chosen, there are three optional entry points at the rear/side of the appliance. -
Page 10: Completing The Installation
Completing the Installation of the Appliance Fit the cast trim (supplied in a separate carton) to the appliance with the fixings provided. The instructions for the assembly is supplied with the trim. Due care and attention should be paid to the installation of the trim as any service call due to incorrect placement of the trim assembly which causes difficulty in lighting the appliance will result in a callout charge being made. -
Page 11: Appliance Technical Information
Maintenance of the Appliance The following procedures can and should be performed by the customer at regular intervals depending upon use of the appliance. Appliance Technical Information Gas Type : Natural Gas Category : I2H Inlet Pressure: (Cold) 20mbar Heat Input Gross : 5.5kW Injector : 69 Destination Countries : GB/ IE HEALTH AND SAFETY NOTICE... -
Page 12: Service Instructions
Cleaning the Appliance (continued) Trim, Fret and Painted Metal Parts There are a variety of trim and fret options which may have been supplied with your appliance and these are normally a plated material on a steel substrate. It is important that no abrasive cleaners or chemical agents are used in the cleaning of these components. - Page 13 Re-assemble the burner tray into the firebox (see previous page) Only replacement components supplied by the manufacturer should be used in the service of this appliance. Contact details for Be Modern Ltd can be found on the back page of these instructions.
-
Page 14: User Instructions
OPERATING INSTRUCTIONS This appliance is available with two operating methods, namely manual control and slide control. The following instructions detail both methods of operation however the basic operation of the appliance involves the ignition of a pilot burner (See page 7 for spillage monitoring details—ODS), then the control of the main burner with LOW and HIGH settings. -
Page 15: Coal Layout Instructions
FUEL BED LAYOUT (COAL) The following instructions detail how the ceramic fuel bed and loose components are to be installed onto the appliance. Great care should be taken when handling these ceramic parts as they are fragile and can easily be broken. Do not force any component into position, if it does not fit easily then you are not fitting the part correctly. - Page 16 Step 3 Fit the four coals onto the front rail and lean against the fuel bed—as shown in the picture below. Step 4 Carefully place five coals onto the fuel bed as shown in the picture below. Step 5 Fit three coals into position as shown in the picture below.
-
Page 17: Fit Trim To The Appliance
Fit Trim to Appliance Position the four magnets supplied in the fitting pack to the rear face of the trim as shown below. STANDARD TRIM TWO TONE TRIM Now fit the trim to the appliance. -
Page 18: Spare Parts List
Ceramic Fuel Bed-Coal P-XX1152 Ceramic Front Rail-Coal P-XX1163 Ceramic Loose Fuel Pack-Coal P-XX1380 Glass Panel (Silk Screened) Be Modern Ltd Bede Industrial Estate , Jarrow, Tyne & Wear, NE32 3BE www.bemodern.com Tel: 0191 489 8006 Fax: 0191 580 0085 Email: sales@bemodern.com Due to our policy of continual product improvement, some diagrams and small details may not be accurate however if there is any concern or matter of understanding that you feel needs to be clarified please contact us directly.
Need help?
Do you have a question about the BM-05XXX1 and is the answer not in the manual?
Questions and answers