List Of Standards; List Of Symbols - DeWalt DWST08810 Instruction Manual

English
way, such as power-supply cord or plug
is damaged, liquid or direct rain has
reached the connectors, the appliance
has been exposed to extensive moisture,
does not operate normally, or has been
dropped and does not operate.
19. This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision
or instruction concerning use of the
appliance by a person responsible for
their safety.
20. Children should be supervised to ensure
that they DO NOT play with the appliance.
21. Use only with specifically designated
DEWALT battery packs (see Important
Safety Instructions for All Battery
Packs below for DEWALT-approved
battery packs). Use of any battery packs
other than those approved by DEWALT
may create a risk of injury and fire.
The lightning flash with arrow head
within a triangle is intended to
tell the user that parts inside the
product are a risk of electric shock
to persons.
The exclamation point within a triangle
is intended to tell the user that important
operating and servicing instructions
are in the user manual supplied with the
appliance.
The double insulation symbol (a
square within a square) indicates a Class
II electrical appliance and is intended
to alert qualified service personnel to
use only identical replacement parts in
this appliance.
IC
This device complies with Industry
RSS210,
Canada License-exempt RSS-210.
Issue 8,
Operation is subject to the following
2010
two conditions: (1) this device may
not cause interference, and (2)
this device must accept any interference,
including interference that may cause
undesired operation of the device.
FCC This appliance complies with the
Federal Communications Commission
regulations.
WARNING: Modifications not expressly
approved by the manufacturer could
void the user authority to operate the
equipment under FCC Rules.
4
NOTE: This equipment has been tested and
found to comply with the limits for a class
B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the following
measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment to an outlet on
a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
WARNING: To reduce the risk of fire
or electric shock, DO NOT expose this
appliance to direct rain or moisture. Use
only in dry locations.
CAUTION: To prevent electric shock,
match the wide blade of the adaptor
plug to the wide slot and fully insert.

LIST OF STANDARDS

The DWST08810 complies with the following
standards:
• ANSI/UL60065
(7 th Edition Rev. July 24, 2013)
• CAN/CSA C22.2 No. 60065:
2003+A1+A2
• ANSI/UL1310
(6 Edition Rev. December 12, 2014)
th
• CSA C22.2 No.223-M91
(Rev. September, 2013)
• IC RSS210, Issue 8, 2010
• ICES-003, Issue 5, 2012
• UL2595 (1 st Revision) dated on May 22,
2013
• FCC part 15: 2013 (ANSI C63.4:2009)
• FCC ID: YJ7DWST08810
• IC: 9082A-DWST08810

LIST OF SYMBOLS

The labels on this appliance may include the
following symbols:
V ............Volts
A ............Amperes
W ............Watts
h ............hours
............Direct current
............Class II Construction (double insulated)
............ETL Testing Laboratories symbol
............Safety alert symbol
IMPORTANT SAFETY INSTRUCTIONS
FOR ALL BATTERY PACKS
When ordering replacement battery packs,
be sure to include the catalog number and
voltage. The DWST08810 is to be used only
with DEWALT DCB series 12VDC/20VDC
Li-ion rechargeable battery packs with 5Ah
max. Use of any other battery packs or any
non-rechargeable batteries may create a risk
of injury or fire.
Recharge only with the DWST08810
integrated charger, or equivalent. A charger
that is suitable for one type of battery pack
may create a risk of fire when used with
another battery pack.
Note: The battery pack is not fully charged
out of the carton. Before using the battery
pack and charger, read the safety instructions
in the following section and then follow the
charging procedures.
THE RBRC™ SEAL
The RBRC™ (Rechargeable Battery Recycling
Corporation) seal on the nickel cadmium,
nickel metal hydride or lithium ion batteries
(or battery packs) indicate that the costs to
recycle these batteries (or battery packs)
at the end of their useful life have already
been paid by DEWALT. In some areas, it is
English
illegal to place spent nickel cadmium, nickel
metal hydride or lithium ion batteries in the
trash or municipal solid waste stream, and the
RBRC program provides an environmentally
conscious alternative. RBRC™, in cooperation
with DEWALT and other battery users, has
established programs in the United States and
Canada to facilitate the collection of spent
nickel cadmium, nickel metal hydride or lithium
ion batteries. Help protect our environment
and conserve natural resources by returning
the spent nickel cadmium, nickel metal hydride
or lithium ion batteries to an authorized
DEWALT service center or to your local retailer
for recycling. You may also contact your local
recycling center for information on where
to drop off the spent battery. RBRC™ is a
registered trademark of the Rechargeable
Battery Recycling Corporation.
READ ALL INSTRUCTIONS
DO NOT charge or use the battery
•
pack in explosive atmospheres, such
as in the presence of flammable
liquids, gases or dust. Inserting or
removing the battery pack from the
charger may ignite the dust or fumes.
• NEVER force the battery pack into the
charger. DO NOT modify the battery
pack in any way to fit into a non-
compatible charger as battery pack
may rupture causing serious personal
injury.
• Charge the battery packs only in
designated D WALT chargers.
E
DO NOT immerse in water or other liquids.
•
• DO NOT store or use the appliance and
battery pack in locations where the
temperature may reach or exceed
105 °F (40 °C) (such as outside sheds or
metal buildings in summer). For best life
store battery packs in a cool, dry location.
WARNING: Fire hazard. NEVER attempt
to open the battery pack for any reason.
If the battery pack case is cracked or
damaged, DO NOT insert into the charger.
DO NOT crush, drop or damage the
battery pack. DO NOT use a battery pack
or charger that has received a sharp
blow, been dropped, run over or damaged
in any way (e.g., pierced with a nail, hit
with a hammer, stepped on). Damaged
battery packs should be returned to the
service center for recycling.
5