1. Manuals
  2. Brands
  3. Encore Manuals
  4. Lawn Mower
  5. Classic 26SP100
  6. Operator's & parts manual

Encore Classic 26SP100 Operator's & Parts Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
26 S P1 0 0
OPERATORS/ P ARTS
MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Classic 26SP100 and is the answer not in the manual?

Questions and answers

Related Manuals for Encore Classic 26SP100

Summary of Contents for Encore Classic 26SP100

  • Page 1 26 S P1 0 0 OPERATORS/ P ARTS MANUAL...
  • Page 2 OPERATORS MANUAL SECTION...

  • Page 3: General Safety Instructions

    We encourage you to contact your local The message that follows the symbol con- Encore dealer for repairs. All Encore dealers tains important information about safety. are informed of the latest methods to service...

  • Page 4: Operation

    objects as damage to machine and/or others GENERAL RULES OF SAFETY FOR may result. OPERATION. Never mow on a surface angle greater than 15 degrees. Mow across a slope less The follow general rules of safety should be than 15 degrees, NEVER up and down. followed whenever THE MOWER IS BEENING USED.
  • Page 5 SET-UP AND MAINTIANENCE CAUTION: Engine has not been serviced prior to delivery. Consult engine manual to properly service engine before use. 1. Install handle by flipping handle into place using the bolts located in the handle support. See diagram a. (Note that the handle frame is slotted so the handle can be adjusted to the right operator height for operator comfort).
  • Page 6 3. Drive chain may be adjusted by loosing the top bracket located by the cog assemble (Refer to figure d) When adjusting the drive chain you must adjust both sides equally. After adjusting the chain reset cog tension by removing the pin in the yoke attached to the cog bracket and shortening the rod length to increase cog pressure.
  • Page 7 HEIGHTS ADJUSTMENTS: 2" 3" 3 1/4" 1 1/2" 2" 3" 3 1/4" Figure C Adjust cut setting by changing wheel heights according to figure (c). Mower blade: Check sharpness of mower blades after every 10 hours of operation. To sharpen blades proceed as follows.
  • Page 8 b. Remove blade by turning bolt counter clockwise. c. Blades should be discarded when worn excessively. See Sketch. New Blade Dangerous! When Notch Starts 25 Degrees Discard Blade d. Sharpen blades with a hand file, electric grinder or blade sharpener. Wear gloves and eye protection when sharpening.
  • Page 9 1. 12 V electric s tarter 9. E ngine Model Type C ode xxxxx xxxx xx xxxxxxxx 2. Oil drain plug 10. Muffler/(Muffler guard, if equipped)/ 3. F uel fill (S park arres ter, if equipped) 4. F uel tank 11.
  • Page 10 PARTS MANUAL SECTION...

  • Page 11: Handle Assembly

    HANDLE ASSEMBLY...
  • Page 12 26" High Wheel Walk-Behind Handle Assembly PART # DESCRIPTION HANDLE ASSY. PART # DESCRIPTION 100258 1/4 - 20 X 2.00 HHCS 101298 # 10 – 24 x 2 1/4 103003 #10-14 x 1/2 PLASTITE SCREW (FOR PLASTIC) 103021 ROPE GUIDE 104255 1/4 - 20 NYLOC NUT 105259...

  • Page 13: Mower Deck Assembly

    MOWER DECK ASSEMBLY...
  • Page 14 26" High Wheel Walk-Behind Mower Deck Assembly PART # DESCRIPTION DEFLECTOR SHIELD FINAL ASSY PART # DESCRIPTION 100273 5/16 – 18 X 1 HHCS 104256 5/16 – 18 NYLOC NUT 104257 3/8 – 16 NYLOC NUT 104512 5/8 – 18 HEX NUT 104755 1/2 - 20 HEX JAM NUT PLATED 105009...
  • Page 15 26" High Wheel Walk-Behind Mower Deck Assembly PART # DESCRIPTION PART # DESCRIPTION 104753 3/8 – 16 JAM NUT 105259 3/8 SAE WASHER 105260 3/8 STD WASHER 262012 BLADE BRAKE WELDMENT 263028 BRAKE BAND 263076 BRAKE SPRING 363097 SPACER - TURNBUCKEL 523328 FLAT IDLER –...

  • Page 16: Drive Assembly

    DRIVE ASSEMBLY...
  • Page 17 26" High Wheel Walk-Behind Drive Assembly PART # DESCRIPTION FINAL ASSY PART # DESCRIPTION 107509 5/16-18 X 1 CARR. BOLT 263050 BELT SHIELD 263063 DRIVE BELT 264012 DRIVE ROD ASSY PART # DESCRIPTION 104754 3/8 – 24 HEX JAM NUT 263034 DRIVE ROD 363192...
  • Page 18 26" High Wheel Walk-Behind Drive Assembly PART # DESCRIPTION PART # DESCRIPTION 5/8 CLAMP COLLAR 363339 BLADE SPACER 373086 363174 EYEBOLT SPACER 363165 COTTER PIN # 2 HAIRPIN 363196 CLEVIS PIN –3/8...
  • Page 19 HEIGHT ADJUSTMENT ASSEMBLY...
  • Page 20 .25 X .25 X 1.00 MACH. KEY 263085 ENGINE PULLEY SEE NOTE 8.5 HP BRIGGS W/FUEL TANK 363075 BELT GUIDE 363226 DISC SPRING NOTE: ENCORE MFG. CO. DO NOT SERVICE OR STOCK PARTS FOR ENGINES ON OUR UNITS. PLEASE CONTACT ENGINE MFG. FOR PART INFORMATION.

  • Page 21: Decal List

    DECAL LIST...
  • Page 22 26" High Wheel Walk-Behind Decal List PART # DESCRIPTION 263031 CLASSIC LABEL 263069 PRO 26 LABEL 263118 WHEEL DRIVE DECAL 363001 CAUTION DECAL 363023 DANGER DECAL 363026 SERIAL NO. PLATE 363317 POLY ENCORE LABEL 363318 POLY ENCORE LOGO 823323 ROTATING PARTS DECAL...

  • Page 23: Encore Warranty

    Any part of the Encore commercial mower manufactured by Encore Mfg. Co., Inc. and found in reasonable judgment of Encore Mfg. Co., Inc. to be defective in material or workmanship, will be repaired or replaced by an authorized Encore Dealer without charge for parts and labor.
  • Page 24 0802 A ,ENCORE MANUFACTURING CO., INC. 26SP100 - OPERATORS/PARTS MANUAL All rights reserved. Contents subject to change. CLASSIC 933113 umber...

Table of Contents