Related Manuals for Fujitsu SK-91465X-100PMC
Summary of Contents for Fujitsu SK-91465X-100PMC
-
Page 1: Evaluation Board
Fujitsu Microelectronics Europe FMEMCU-UG-910056-11 User Guide MB91F465XA EVALUATION BOARD SK-91465X-100PMC USER GUIDE... -
Page 2: Revision History
SK-91465X-100PMC User Guide Revision History Revision History Date Issue 2007-04-11 V1.0, MSt Initial version 2008-09-05 V1.1, MSc, China-RoHS regulation added This document contains 40 pages. UG-910056-11 - 2 - © Fujitsu Microelectronics Europe GmbH... -
Page 3: Warranty And Disclaimer
Warranty and Disclaimer To the maximum extent permitted by applicable law, Fujitsu Microelectronics Europe GmbH restricts its warranties and its liability for the SK-91465X-100PMC and all its deliverables (eg. software include or header files, application examples, target boards, evaluation boards, engineering samples of IC’s etc.), its performance and any consequential damages, on the use of the Product in... -
Page 4: Table Of Contents
UART”B” / LIN “A” ....................17 UART ”C” / LIN “B” ....................18 CAN “A”......................... 19 CAN “B”......................... 19 FlexRay “Channel A” (FR-A).................. 20 3.10 FlexRay “Channel B” (FR-B).................. 21 3.11 Reset-Generation ....................22 UG-910056-11 - 4 - © Fujitsu Microelectronics Europe GmbH... - Page 5 Silk-plot Top-side....................33 Silk-plot bottom side ....................34 7 RELATED PRODUCTS ....................35 8 APPENDIX........................36 Tables ........................36 Figures ........................37 9 CHINA-ROHS REGULATION ..................38 10 RECYCLING ........................40 © Fujitsu Microelectronics Europe GmbH - 5 - UG-910056-11...
-
Page 6: Introduction
Chapter 1 Introduction 1 Introduction 1.1 Abstract The SK-91465X-100PMC is a multifunctional evaluation board for the Fujitsu 32-bit FR60 Flash microcontroller series MB91F465XA. It can be used stand-alone for software development and testing or as a simple target board to work with the emulator system. -
Page 7: General Description
The LIN transceivers (TLE7259) generate the adequate levels to drive the bus line in LIN- systems for automotive and industrial applications. 1.3.6 I²C Two additional pull-up resistors R24 and R25 can be connected to the I²C bus lines by setting the according Jumpers (JP18, JP22). © Fujitsu Microelectronics Europe GmbH - 7 - UG-910056-11... -
Page 8: Mcu Pins
+12V (max. 2600 mA) to the starter-kit. The switching regulator provide the voltages of 5V (1.6A), 3.3V (1.6A) on the starter kit. The switching regulators are short circuit protected and provide a thermal shutdown. UG-910056-11 - 8 - © Fujitsu Microelectronics Europe GmbH... -
Page 9: Installation
Select the low voltage adapter suitable to the power connector X13 at the SK-91465X- 100PMC and plug it to the connecting socket in the right orientation (+ connected to shield and GND connected to centre pin). Figure 2-4: Low voltage adapter selection © Fujitsu Microelectronics Europe GmbH - 9 - UG-910056-11... -
Page 10: Jumper Settings
Chapter 2 Installation Now connect the DC low voltage adapter to the Starter kit and plug in the In-Plug Power Supply to a power socket. The SK-91465X-100PMC can be turned on with the on board power switch S2. For the power supply of the SK-91465XA-100PMC a DC input voltage of 12V is recommended. - Page 11 Clock BNC X0/Pin16 Solder JP 3 pin Open JP74 X14 / X1 Solder JP 2 pin Closed JP75 X14 / X0 Solder JP 2 pin Closed Table 2-1: Default jumper settings © Fujitsu Microelectronics Europe GmbH - 11 - UG-910056-11...
-
Page 12: Jumper Coordinates
2.2 Jumper Coordinates UART “B“ / UART “C“ LIN“B“ LIN“A“ UART7 UART6 CAN “A” UART “A” CAN4 UART4 FlexRay CAN “B” Channel A CAN0 FlexRay Channel B Figure 2-5: Jumper Coordinates UG-910056-11 - 12 - © Fujitsu Microelectronics Europe GmbH... -
Page 13: Jumpers And Switches
1 (high) S1/3 (MD2) OFF (open) 0 (low) S1/4 not connected Default: grey Table 3-1: MCU operating mode MD0 MD1 MD2 nc Dip-Switch S2 (default setting) Figure 3-1: MCU Mode Switch © Fujitsu Microelectronics Europe GmbH - 13 - UG-910056-11... -
Page 14: Power Supply
Open No voltage supply to Vs of LIN A Closed Vs of LIN B is powered by the board (Vin) JP60 Open No voltage supply to Vs of LIN B (Vin_B) UG-910056-11 - 14 - © Fujitsu Microelectronics Europe GmbH... -
Page 15: Power Switching By Flexray Physical Layer
INHx-B connected to JP25 Select Channel A INH1 JP19 Select Channel A INH2 Select Channel B INH1 JP31 Select Channel B INH2 Default: grey Table 3-3: Jumper Settings FlexRay power switching © Fujitsu Microelectronics Europe GmbH - 15 - UG-910056-11... -
Page 16: Analogue Power Supply Voltage
(AVcc and AVss) to the A/D-converter. If JP3 is open, the resistors R8 and R11 define AVRH. By default the resistor network (R8, R11) is not mounted on the board. UG-910056-11 - 16 - © Fujitsu Microelectronics Europe GmbH... -
Page 17: Uart"A
BUS Signal (LINA) is connected to pin2 of X8 (X8 pin2) Tx Signal (UARTB) is connected to pin2 of X8 JP49 Closed RTS and CTS of X8 are connected (RTS-CTS) Open RTS and CTS of X8 are not connected © Fujitsu Microelectronics Europe GmbH - 17 - UG-910056-11... -
Page 18: Uart "C" / Lin "B
Open RTS and CTS of X12 are not connected JP57 Closed LIN-transceiver is enabled (LIN B enable) Open LIN-transceiver is disabled JP54 Closed LIN Master-mode (LIN B Master) Open LIN Slave-mode UG-910056-11 - 18 - © Fujitsu Microelectronics Europe GmbH... -
Page 19: Can "A
RX0 of the MCU is not connected to CAN”B” Closed TX0 of the MCU is connected to CAN”B” (X2) JP16 (CAN”B”TxD) Open TX0 of the MCU is not connected to CAN”B” Default: grey Table 3-9: CAN “B” jumper settings © Fujitsu Microelectronics Europe GmbH - 19 - UG-910056-11... -
Page 20: Flexray "Channel A" (Fr-A)
ERRN of the FR-A is connected to MCU pin. JP47 Closed ERRN of the FR-A is not connected to MCU pin. (ERRN-A) Open Default: grey Table 3-10: FlexRay “Channel A” jumper settings UG-910056-11 - 20 - © Fujitsu Microelectronics Europe GmbH... -
Page 21: Flexray "Channel B" (Fr-B)
ERRN of the FR-B is connected to MCU pin. JP51 Closed ERRN of the FR-b is not connected to MCU pin. (ERRN-B) Open Default: grey Table 3-11: FlexRay “Channel B” jumper settings © Fujitsu Microelectronics Europe GmbH - 21 - UG-910056-11... -
Page 22: Reset-Generation
No negation for the DTR/RTS signal JP33 (Polarity) DTR/RTS signal is negated Default: grey Table 3-12: Reset Jumper Settings Note 1: JP28, JP33, JP50, JP71 and JP72 default setting is open. UG-910056-11 - 22 - © Fujitsu Microelectronics Europe GmbH... -
Page 23: Buttons Sw1, Sw2, Sw3, Sw4, Sw5, Sw6, Sw7
No connection to INITX WAKE of FlexRay Transceiver Ch. A is connected to SW7 JP70 (WAKE) WAKE of FlexRay Transceiver Ch. B is connected to SW7 Default: grey Table 3-13: Buttons Jumper settings © Fujitsu Microelectronics Europe GmbH - 23 - UG-910056-11... -
Page 24: Programming The Internal Flash
3. Start the Flash programmer by double-clicking on the flashprg.exe icon 4. Select appropriate MCU type, COM-Port, baudrate, and the path to your HEX-File (.mhx) 5. Power-off the board or assert and hold RESET UG-910056-11 - 24 - © Fujitsu Microelectronics Europe GmbH... - Page 25 CAUTION : DO NOT INTERRUPT OR CUT OFF POWER DURING ERASE !!! 7. When download and programming is completed successfully, following screen appears: 8. After successful programming, reset or Power off/on the board to start the application. © Fujitsu Microelectronics Europe GmbH - 25 - UG-910056-11...
-
Page 26: Synchronous Mode
A dedicated Flash programming socket (J4) is provided on the evaluation-board for direct connection to this programmer. n/c 1 2 n/c MD0 3 4 MD2 RST 5 6 SIN4 SOT4 7 8 SCK4 VCC 9 10 GND Figure 4-1: J4 Flash programming socket UG-910056-11 - 26 - © Fujitsu Microelectronics Europe GmbH... -
Page 27: Connectors
51 – 100 Table 5-1: MCU Pin Connectors The odd pin numbers are located on the one side and the even pin numbers are located on the other side of the connector. © Fujitsu Microelectronics Europe GmbH - 27 - UG-910056-11... -
Page 28: Uart / Lin Connector (X6, X8, X12)
Ground normally used for LIN connection Shield Ground Table 5-2: UART Connector Signals Note: Connector X6 is connected to RS232, only. Connector X8 and X12 can be connected to RS232 or LIN. UG-910056-11 - 28 - © Fujitsu Microelectronics Europe GmbH... -
Page 29: Can Connector (X1, X2)
Connected to Jumper (CH-A: JP30; CH-B: JP17) Not used Bus line Plus Not used Not used Shield Connected to GND via Jumper Shield (CH-A: JP39; CH-B: JP23) Table 5-4: FlexRay Connector Signals © Fujitsu Microelectronics Europe GmbH - 29 - UG-910056-11... -
Page 30: User-Leds & Optional Lc-Display
RN2 can be removed. Instead of the user-LEDs an alphanumeric LC-Display (optional) can be connected. The following control signals are provided: VLSS VLED VCC GND Port 27_3 27_2 27_1 27_0 16_3 16_2 16_1 16_0 UG-910056-11 - 30 - © Fujitsu Microelectronics Europe GmbH... -
Page 31: In-Circuit-Programming Connector (J4)
Not used MCU mode-pin 0 MCU mode-pin 2 INITX MCU reset signal SIN4 UART4 receive data SOT4 UART4 transmit data SCK4 UART4 clock Board supply voltage Ground Table 5-5: In-Circuit Programming Connector © Fujitsu Microelectronics Europe GmbH - 31 - UG-910056-11... -
Page 32: Vg96 Connector (J1)
Crystal 32kHz P19_0/SIN4 JP26 (UART A) 3A,B,C VSS5 P19_1/SOT4 JP29 (UART A) Crystal 4MHz P19_2/SCK4 Crystal 4MHz P17_0/PPG0 Pulldown 1k P17_1/PPG1 Pulldown 1k VDD5 3A,B,C VSS5 Table 5-6: VG96 (J1) Signals UG-910056-11 - 32 - © Fujitsu Microelectronics Europe GmbH... -
Page 33: Silk-Plot Of The Board
SK-91465X-100PMC User Guide Chapter 6 Silk-Plot of the Board 6 Silk-Plot of the Board 6.1 Silk-plot Top-side Figure 6-1: Silk-plot top side © Fujitsu Microelectronics Europe GmbH - 33 - UG-910056-11... -
Page 34: Silk-Plot Bottom Side
SK-91465X-100PMC User Guide Chapter 6 Silk-Plot of the Board 6.2 Silk-plot bottom side Figure 6-2: Silk-plot Bottom side UG-910056-11 - 34 - © Fujitsu Microelectronics Europe GmbH... -
Page 35: Related Products
< EMA-MB91465X-NLS-100M20 Emulator probe cable for MB91F465X MCU < NQPack100SD-ND Socket for package FPT-100P-M20 (Tokyo Eletech Corp. www.tetc.co.jp/e_tet.htm) < HQPack100SD Header for NQPACK100SD < MB91460 Series < MB91V460A MB91460 Series Evaluation chip < MB91F465XAPMC Flash MCU © Fujitsu Microelectronics Europe GmbH - 35 - UG-910056-11... -
Page 36: Appendix
Table 5-2: UART Connector Signals ..................28 Table 5-3: CAN Connector Signals ..................29 Table 5-4: FlexRay Connector Signals ................. 29 Table 5-5: In-Circuit Programming Connector ..............31 Table 5-6: VG96 (J1) Signals ....................32 UG-910056-11 - 36 - © Fujitsu Microelectronics Europe GmbH... -
Page 37: Figures
Figure 5-3: CAN Connector....................29 Figure 5-4: FlexRay Connector .................... 29 Figure 5-5: In Circuit Programming Connector ..............31 Figure 6-1: Silk-plot top side....................33 Figure 6-2: Silk-plot Bottom side ..................34 © Fujitsu Microelectronics Europe GmbH - 37 - UG-910056-11... -
Page 38: China-Rohs Regulation
“Year”. UG-910056-11 - 38 - © Fujitsu Microelectronics Europe GmbH... - Page 39 X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ/T11363-2006. • Data listed in the table represents best information available at the time of publication © Fujitsu Microelectronics Europe GmbH - 39 - UG-910056-11...
-
Page 40: Recycling
According to the European WEEE-Directive and its implementation into national laws we take this device back. For disposal please send the device to the following address: Fujitsu Microelectronics Europe GmbH Warehouse Monzastraße 4a 63225 Langen -- END -- UG-910056-11 - 40 - © Fujitsu Microelectronics Europe GmbH...