Related Manuals for Eko-Vimar Orlanski orlan standart
Summary of Contents for Eko-Vimar Orlanski orlan standart
- Page 1 ® ® e-mail: orlanski@eko-vimar.com.pl www.eko-vimar.com.pl tel.: +48 77/ 400 55 80÷81, 400 55 91 fax: +48 77/ 439 05 03, 400 55 96 EKO-VIMAR ORLAÑSKI ul. Nyska 17b 48-385 Otmuchów / woj. opolskie POLSKA...
- Page 2 Boiler connected in cascade enables heating of bigger buildings. Boilers should be of the same output. Such system gives better possibilities of heat source dynamics than system with one boiler only. Particularly in .transition period. (springtime or autumn) boilers may be serviced alternately. Boilers with such connection enables for its exploitation with the output close to nominal, what warrants boiler longer durability.
-
Page 3: Table Of Contents
18. ORLAN SUPER APPENDIX MANUAL CONTENS: ADDITIONALLY IN ORLAN SUPER ORLAN SUPER is additionally equipped with mechanical clearing system of the 1. Appropriation ..................4 smoke tube exchanger and thermal safety device built into the boiler body. 2. General requirements ............... 4 THERMAL SAFETY DEVICE ( COOLING COIL ) 3. -
Page 4: Appropriation
1. BOILER APPROPRIATION 17. FAULTS CAUSED BY IMPROPER BOILER USE AND THEIR REMOVING If boiler temperature achieves 90ºC safety device will switch of the fan. To burn Low temperature water boilers (up to 95ºC) are produced as 18, 25, 40, 60 and| the boiler again - see point “BOILER OVERHEATING”. - Page 5 (gasification process totally fade). In result a wood tar seats on the boiler walls. d) Boiler room should be equipped with both natural and artificial light To avoid a/m situation we recommend to install the four-way mixing valve on boiler e) Boiler room must be equipped with unclosed supply ventilation 400 cm outlet.
-
Page 6: Boiler Technical Specification
Tightness assertion The boiler tightness is very important especially if we are thinking of boiler's door, heat exchanger lid and chimney flap. If one of these is leaky the smoke can come out of the boiler room but first of all it may be the reason of uncontrolled burning into the boiler what may also overheat the boiler. - Page 7 The system works by: To fill the boiler up: 1.switch off the fan using boiler master switch water temperature setup on the boiler exit ( wide temp. range 65 - 80º C) 2.open chimney flap signaling of excessive water increase and also excessive water drop 3.open upper door and fill up the boiler with wood fan switching off when the water temperature on the boiler achieves the 4.close chimney flap, door, and wood switch on the master switch...
-
Page 8: Technical Data
4. Technical specification of the Orlan boilers 15. BOILER EXPLOITATION Boiler dimensions Before first boiler start-up you should check all of threaded connections (if there is no leakage) and also water level into central heating system - then set-up boiler working parameters. -
Page 9: Programming
6. PROGRAMMING 11. ROOM THERMOSTAT SETTING-UP RK 2001E regulator is equipped with a special input, placed on its back wall, RK 2001 R4E Regulator enabling room thermostat connecting (always delivered with each boiler). When 1. master switch room temperature is lower than assigned one then the boiler indicator begins to shine what means that the boiler should keep ordered temperature. -
Page 10: Regulator Working Description
back wall. On the same wall there is also placed room thermostat socket and time FUEL SHORTAGE regulation handwheels If boiler temperature gets down under 65ºC and it is continued by 30 min., then 10. REGULATOR WORKING DESCRIPTION regulator switch off the fan and switch on the fuel shortage indicator. In case of regulation repeated switching off, you should: Regulator's work is based on suitable controlling of the fan and heating system fill up the boiler with wood or to burn the boiler again if necessary...
Need help?
Do you have a question about the orlan standart and is the answer not in the manual?
Questions and answers