Maintenance And Troubleshooting - Weslo CardioStrite Plus WETL01540 User Manual

MAINTENANCE AND TROUBLESHOOTING

Most problems can be solved by following the simple steps below. If further assistance is needed,
please call our Customer Service Department.
1. SYMPTOM: THE CONSOLE DOES NOT
FUNCTION PROPERLY
a. Replace the batteries in the console (see assem-
bly step 6 on page 5).
b. Make sure that the reed switch is properly adjust-
ed (see assembly step 4 on page 4).
c. Make sure that the handrail wire is plugged fully
into the wire on the console (see assembly step 7
on page 5).
d. The console, like most electronics, is susceptible
to static electricity build-up caused by certain
types of clothing or by the operation of the tread-
mill. If the display is blank or gives incorrect read-
ings, apply an anti-static spray to the handrail.
Anti-static spray is available where laundry sup-
plies are sold.
2. SYMPTOM: THE WALKING BELT DOES NOT
MOVE SMOOTHLY
a. If the walk-
ing belt is
Walking
overtight-
Belt
ened, per-
formance
may be
reduced and
the walking
belt may be
permanently 5–7 cm
Bolts
damaged.
Using the
hex key,
turn both rear roller adjustment bolts counter-
clockwise 1/4 of a turn. When the tension of the
walking belt is correct, you should be able to lift
each side of the walking belt 5 to 7 cm (2 to 3 in.).
Walk on the treadmill for a few minutes. Repeat
until the walking belt is properly tightened. Be
careful to keep the walking belt centred.
3. SYMPTOM: THE WALKING BELT SLIPS OR IS
OFF-CENTRE
a. If the walking
belt slips
when walked
on, use the
hex key to turn
both adjust-
ment bolts
clockwise, 1/4
of a turn. When
the walking belt is correctly tightened, you should
be able to lift each side of the walking belt 5 to 7
cm (2 to 3 in.). Walk on the treadmill for a few
minutes. Repeat until the walking belt is properly
tightened. Be careful to keep the walking belt cen-
tred.
b. If the walking
belt has shift-
ed to the left
side, use the
hex key to turn
the left adjust-
ment bolt
clockwise, and
the right adjust-
ment bolt counterclockwise, 1/4 of a turn each.
Be careful not to overtighten the walking belt.
Walk on the treadmill for a few minutes. Repeat
until the walking belt is centred.
c. If the walking
belt has shift-
ed to the right
side, use the
hex key to turn
the left adjust-
ment bolt coun-
terclockwise,
and the right
adjustment bolt clockwise, 1/4 of a turn each. Be
careful not to overtighten the walking belt. Walk
on the treadmill for a few minutes. Repeat until the
walking belt is centred.
8
5. Hold the Handrail (5) near the Left and Right Uprights (35,
36). Connect the Handrail Wire (2) to the Reed Switch
Wire (6). Insert the Wires down into the Left Upright.
Attach the Handrail (5) to the Uprights (35, 36) with four
M8 x 15mm Bolts (33) and four M8 Washers (34). Be
careful not to pinch the Wires (2, 6).
See step 1. Tighten the four M8 Nylon Nuts (13).
6. The Console (1) requires two "AAA" batteries. Alkaline
batteries are recommended. Press the indicated tab on
the Battery Cover (27), and remove the Battery Cover.
Insert two batteries into the two battery clips; make sure
that the negative (–) ends of the batteries are touch-
ing the springs in the battery clips.
7. See drawing 7a. Hold the Console (1) near the Handrail
(5). Connect the wire on the Console to the Handrail
Wire (2). Attach the Console to the Handrail with two M4
x 12mm Screws (3). Make sure that the wires are not
pinched.
See drawing 7b. Press the Battery Cover (27) back onto
the Console (1).
8. Remove the paper backing from the Adhesive Clip (30).
Press the Adhesive Clip onto the Left Frame Endcap (24)
in the indicated location. Press the Hex Key (20) into the
Adhesive Clip.
Make sure that the walking belt is properly tightened (see
SYMPTOM 3 on page 8).
9. Make sure that all parts are properly tightened before you use the treadmill. To protect the floor or carpet,
place a mat under the treadmill.
5
33
34
2
6
35
34
36
6
Batteries
1
Tab
27
7a 7b
1
2
5
3 27
8
20
30
24
5
5
33
1