1. Manuals
  2. Brands
  3. Everglades Manuals
  4. Boat
  5. 355 CC
  6. Owner's manual

Everglades 355 CC Owner's Manual

2013
Hide thumbs
Table of Contents

Advertisement

Quick Links

OWNER'S MANUAL
2013
355 CC
355 CCX

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 355 CC and is the answer not in the manual?

Questions and answers

Related Manuals for Everglades 355 CC

Summary of Contents for Everglades 355 CC

  • Page 1 OWNER’S MANUAL 2013 355 CC 355 CCX...
  • Page 2 Revision 1 6-28-2012...

  • Page 3: Table Of Contents

    TABLE OF CONTENTS TABLE OF CONTENTS ......................3 SAFETY INFORMATION ......................7 BOAT INFORMATION ......................8 SPECIFICATIONS ........................ 9 SPECIFICATIONS .......................10 CERTIFICATIONS & SPECIFICATIONS ...................11 INTRODUCTION & IMPORTANT INFORMATION ...............13 OWNER / OPERATOR INFORMATION ..................15 Chapter 1: SAFETY EQUIPMENT 1.1 General ........................17 1.2 Engine Alarms ......................17 1.3 Neutral Safety Switch ....................17 1.4 Engine Stop Switch .....................17...
  • Page 4 TABLE OF CONTENTS Chapter 4: HELM CONTROL SYSTEMS 4.1 General ........................45 4.2 Engine Throttle and Shift Controls .................45 4.3 Neutral Safety Switch ....................47 4.4 Engine Power Tilt and Trim ...................47 4.5 Engine Stop Switch .....................48 4.6 Steering System ......................49 4.7 Trim Tabs ........................49 4.8 Bow Thruster (Optional) ....................50 4.9 Control Systems Maintenance ..................51 Chapter 5:...
  • Page 5 TABLE OF CONTENTS Chapter 9: DRAINAGE SYSTEMS (Continued) 9.4 Bilge Drainage ......................82 9.5 Aft Fishbox and Baitwell Aft Fishbox ................82 9.6 Head Compartment Drainage ..................82 9.7 Drainage System Maintenance ..................83 Chapter 10: VENTILATION SYSTEM 10.1 Head Compartment Ventilation ..................85 10.2 Windshield Ventilation ....................86 10.3 Bilge and System Compartment Ventilation ..............86 10.4 Maintenance ......................87 Chapter 11:...
  • Page 6 TABLE OF CONTENTS Appendix A: SCHEMATICS ........................127 Appendix B: GLOSSARY OF TERMS ......................129 Appendix C: MAINTENANCE LOG ......................133 Appendix D: BOATING ACCIDENT REPORT ....................137 Appendix E: FLOAT PLAN ........................141 Appendix F: TROUBLESHOOTING GUIDE ....................143...

  • Page 7: Safety Information

    SAFETY INFORMATION Your Everglades owner’s manual has been written to include a number of safety instructions to assure the safe operation and maintenance of your boat. These instructions are in the form of DANGER, WARNING and CAUTION statements. The following definitions apply:...

  • Page 8: Boat Information

    BOAT INFORMATION Please fill out the following information section and leave it in your Everglades owner’s manual. This information will be important for you, your dealer and/or Everglades service personnel to know, if you may need to call them for technical assistance or service.

  • Page 9: Specifications

    SPECIFICATIONS 355 CC Specifications HULL LENGTH OVERALL W/ ENGINE _____________________________________________________ 38’ 0” BEAM _______________________________________________________________________________ 10’ 8” WEIGHT DRY - NO ENGINES _________________________________________________________ 9,500 lbs DEAD RISE _____________________________________________________________________________ 25 DRAFT WITH ENGINES UP _______________________________________________________________ 24” DRAFT WITH ENGINES DOWN _____________________________________________________________ 41”...

  • Page 10: Specifications

    SPECIFICATIONS 355 CCX Specifications HULL LENGTH OVERALL W/ ENGINE _____________________________________________________ 38’ 0” BEAM _______________________________________________________________________________ 10’ 8” WEIGHT DRY - NO ENGINES _________________________________________________________ 9,800 lbs DEAD RISE _____________________________________________________________________________ 25 DRAFT WITH ENGINES UP _______________________________________________________________ 24” DRAFT WITH ENGINES DOWN _____________________________________________________________ 41” TRANSOM HEIGHT __________________________________________________________________ 30”...

  • Page 11: Certifications & Specifications

    CERTIFICATIONS & SPECIFICATIONS 355 CC Export Documentation (For Export Only) To be in compliance with European directives for recreational boats as published by the International Organization for Standardization (ISO) in effect at the time this boat was manufactured, we are providing the following information.
  • Page 12 To be in compliance with European directives for recreational boats as published by the International Organization for Standardization (ISO) in effect at the time this boat was manufactured, we are providing the following information. Manufacturer: Name Everglades Boats 544 Air Park Road Edgewater, FL Zip Code: 32132...

  • Page 13: Introduction & Important Information

    It has been written to be clearly stated and easily understood. If you have IMPORTANT: any questions after reading the warranty, please The terms and conditions of the Everglades Boats contact the Everglades Boats Customer Service Limited Warranty are outlined in the warranty Department.

  • Page 14: Product Changes

    INTRODUCTION & IMPORTANT INFORMATION Transferring the Limited Structural Warranty Service For a transfer fee, Everglades Boats will offer to All warranty repairs must be performed by an extend a Transferable Limited Structural Hull War- authorized Everglades Dealer. Should a problem ranty to subsequent owners of Everglades Boats.

  • Page 15: Owner / Operator Information

    OWNER / OPERATOR INFORMATION Registration and Numbering an accident. If you need additional information regarding accident reporting, please call the Boat- Federal law requires that all undocumented ves- ing Safety Hotline, 800-368-5647. sels equipped with propulsion machinery be regis- tered in the state of principal use. A certificate of Education number will be issued upon registering the boat.
  • Page 16 THIS PAGE WAS LEFT BLANK INTENTIONALLY...

  • Page 17: Safety Equipment

    Chapter 1: SAFETY EQUIPMENT 1.1 General Your boat and outboard engines have been equipped with safety equipment designed to en- hance the safe operation of the boat and to meet U.S. Coast Guard safety standards. The Coast Guard or state, county and municipal law enforce- ment agencies require certain additional accessory safety equipment on each boat.

  • Page 18: Visual Distress Signals

    Guard emphasizes that PFDs should be worn at all times when the vessel is underway. Throwable devices must be immediately available for use. All Everglades boats must be equipped with at least Non-Pyrotechnic Devices one Type I, II or III PFD for each person on board, Non-Pyrotechnic visual distress signals must be plus one throwable device (Type IV).

  • Page 19: Navigation Lights

    Safety Equipment • Electric Distress Light (Night use only) Refer to the “Federal Requirements And Safety Tips For Recreational Boats” pamphlet or Contact The electric distress light is accepted for the U.S. Coast Guard Boating Safety Hotline, night use only and must automatically flash 1-800-368-5647, for information on the type and the international SOS distress signal.

  • Page 20: First Aid

    Safety Equipment 1.7 First Aid Satellite EPIRBS EPIRBs (Emergency Position Indicating Radio It is the operator’s re- Beacon) operate as part of a worldwide distress sponsibility to be familiar system. When activated, EPIRBs will send distress with the proper first- code homing beacons that allow Coast Guard aid procedures and be aircraft to identify and find them quickly.

  • Page 21: Caution And Warning Labels

    Safety Equipment 1.9 Caution and Warning Labels The caution and warning labels shown are examples of the labels that could be on your boat. The actual labels and their location could vary on your boat.
  • Page 22 THIS PAGE WAS LEFT BLANK INTENTIONALLY...

  • Page 23: Operation

    2.1 General the boat as well. Always modify the boat speed in accordance with the sea conditions, boat traffic Before you start the engines on your Everglades, and weather conditions. you should have become familiar with the vari- ous component systems and their operation and Remember, it is the operator’s responsibility to...

  • Page 24: The General Prudential Rule

    Operation Overtaking Situations When one motor boat is overtaking another mo- tor boat, the boat that is being passed has the right-of-way. The overtaking boat must make the adjustments necessary to provide clearance for a safe passage of the other vessel. The boats should sound the appropriate signals.
  • Page 25 Operation...

  • Page 26: Pre-Cruise Check

    Operation 2.3 Pre-Cruise Check • Have a tool kit aboard. The kit should include the following basic tools: Before Starting the Engines: Hammer Electrician’s tape • Check the weather forecast and sea conditions before leaving the dock. Decide if the planned Screwdrivers Offset screwdrivers cruise can be made safely.

  • Page 27: Operating Your Boat

    Alcohol reduces night vision and the ability to conditions improve. distinguish red from green. • Your Everglades is a heavy boat that will pro- duce a large wake at certain speeds. You are WARNING responsible for damage and injury caused by your boat’s wake.

  • Page 28: Docking, Anchoring And Mooring

    Operation • As different types of engines are used to • Turn off all electrical equipment except the power the boat, have the dealer describe the automatic bilge pumps. operating procedures for your boat. For more • If you are going to leave the boat for a long instructions on “How To Operate The Boat,”...
  • Page 29 Operation Maneuvering to the Dock Notice: If your boat is equipped with triple engines, we recommend turning the center engine After Bow Spring Cleat off and using the port and starboard engines Stern Cleat Bow Cleat to maneuver the boat to the dock or back it into a slip.

  • Page 30: Controls, Steering Or Propulsion System Failure

    Operation Mooring cal. It should release when you pass that point. If the anchor doesn’t release right away, stop the Approach the mooring heading into the wind or boat directly above the anchor and tie the line to current. Shift to neutral when you have just the cleat as tight as possible.

  • Page 31: Grounding, Towing And Rendering Assistance

    It is much easier for the Coast THE MOORING CLEATS ON EVERGLADES BOATS ARE Guard, aircraft or other boats to spot, than people NOT DESIGNED OR INTENDED TO BE USED FOR TOWING in the water.

  • Page 32: Tower Operation (Optional)

    Operation the boat’s motion is greatly exaggerated for the • Be careful when using the trim tabs from the person in a tower. tower. The reaction of the trim tabs will be exaggerated in the tower. Use small tab cor- If you are fishing in an area that is crowded with rections and wait ten (10) seconds for the tabs other fishing boats, it may be difficult to follow...

  • Page 33: Man Overboard

    Operation 2.12 Man Overboard If you are an experienced driver, you should take some time to become familiar with the boat and If someone falls overboard, you must be pre- the way it handles before pulling a skier. The pared to react quickly, particularly when you are driver should also know the skier’s ability and offshore.

  • Page 34: Teak Surfing

    Operation • Never follow directly behind another boat while pulling skiers. Always stay a safe distance behind or off the side of other boat traffic. If the boat you are following stops unexpectedly, you may not be able to respond quick enough endangering your skier and occupants of both boats.

  • Page 35: Trash Disposal

    Operation 2.15 Trash Disposal gage in teak surfing and warns that teak surfing may cause carbon monoxide poisoning and even The discharge of plastic trash or trash mixed with fatalities. plastic is illegal anywhere in the marine environ- ment. U.S. Coast Guard regulations also restrict Teak surfing not only exposes an individual to the dumping of other forms of garbage.

  • Page 36: Trailering Your Boat

    Important Note: Your Everglades is a heavy boat and care must be taken when selecting the trailer. We • Make sure the trailer bunks and/or rollers recommend that you use a bunk style trailer...
  • Page 37 STRAKES AND ARE PROVIDING ENOUGH SUPPORT FOR THE or chain is also installed to the tow vehicle HULL. HULL DAMAGE RESULTING FROM IMPROPER TRAILER frame. SUPPORT IS NOT COVERED BY THE EVERGLADES WARRANTY. • Make sure the LIGHTS on the trailer function properly.
  • Page 38 THIS PAGE WAS LEFT BLANK INTENTIONALLY...

  • Page 39: Propulsion System

    Chapter 3: PROPULSION SYSTEM 3.1 General Your Everglades is designed to be powered with 4-cycle outboard motors. 4-cycle outboard en- gines do not use an oil injection system and are not equipped with remote oil tanks. They have an oil sump in the crankcase that must be kept full of the type of oil recommended by the engine manufacturer.

  • Page 40: Engine Lubrication

    The propellers convert the engine’s power into CAN CAUSE SEVERE DAMAGE TO THE ENGINE. CONTACT thrust. They come in a variety of styles, diam- YOUR EVERGLADES DEALER OR ENGINE MANUFACTURER eters and pitches. All boats powered by Yamaha FOR INFORMATION ON THE PROPER PAINTING PROCEDURES.
  • Page 41 Notice: Outboard engines can be damaged and the warranty void if the boat is not propped correctly. Always consult your Everglades dealer or authorized engine service dealer when making changes to the propellers or if the boat does not run near the top recom-...

  • Page 42: Engine Instrumentation

    Most Everglades boats are equipped with Yamaha The tachometer display also contains the engine engines and Command Link Plus LCD multifunc- ®...

  • Page 43: Fuel Gauge

    Propulsion System options are installed in your boat. Refer to the engine gauge and electronics operating manuals for more information on the speedometer options available for your boat. Overheat Warning Indicator The temperature warning indicates that the tem- perature of the engine is too high. A sudden increase in the temperature could indicate an obstructed water inlet or an impeller failure.
  • Page 44 Propulsion System Compass All boats are equipped with a compass on the top of the instrument panel. The compass cannot be adjusted accurately at the factory as it must be compensated for the influence of the electrical equipment and electronics unique to your boat. Therefore, the compass should be adjusted by a professional after the electronics and additional electrical accessories are installed and before op-...

  • Page 45: Helm Control Systems

    Chapter 4: HELM CONTROL SYSTEMS 4.1 General The helm controls consist of three systems: the engine throttle and shift controls, the steering system and the trim tab control switches. These systems provide the operator with the ability to control the direction and attitude of the boat from the helm station.
  • Page 46 Helm Control Systems provided directly on the control and a master trim switch is located on the port handle. The port throttle lever controls both the port and center engine when all three engines are selected by the engine selector switch. General control operation is very similar to the twin engine control.

  • Page 47: Neutral Safety Switch

    If necessary, the maximum any position other than the neutral position. If tilt angle can be adjusted by your Everglades or the engine will not start, slight movement of the Yamaha dealer by reprogramming the settings us- shift lever may be necessary to locate the neutral ing the Yamaha engine diagnostic system.

  • Page 48: Engine Stop Switch

    Helm Control Systems Moving the outboards closer to the boat transom is called trimming “in” or “down.” Moving the out- boards further away from the boat transom is called trimming “out” or “up.” In most cases, the boat will run best with the outboards adjusted so the hull will run at a 3 to 5 degree angle to the water.

  • Page 49: Steering System

    Power Assist Hydraulic Steering The power assist steering system is standard equip- ment with both steering systems on the 355 CC. It is comprised of two hydraulic circuits: a manual system, which is the control element and a hy- draulic power pump, which is the working element.

  • Page 50: Bow Thruster (Optional)

    Helm Control Systems bow up and down movements. It also controls starboard and port up and down movements. Bow up and bow down will control the hull planing attitude, while port and starboard up and down provides control for the hull listing. An LED indicator built into the switch displays the position of your trim tabs.

  • Page 51: Control Systems Maintenance

    Replace if sary. If adjustments become necessary, see your necessary. Failure to do so could lead to steering Everglades dealer. system failure that would result in loss of control. WARNING When new or after repairs, hydraulic steering systems may need to have all air purged from the system.
  • Page 52 The bow thruster is mounted in the forward bilge damage the bow thruster and void the warranty. below the center hatch. Periodically inspect the Contact your authorized Everglades dealer or the components inside the hull for leaks and for loose bow thruster manufacturer for information regard- or corroded electrical connections.

  • Page 53: Fuel System

    Chapter 5: FUEL SYSTEM 5.1 General The gasoline fuel system used in Everglades boats is designed to meet or exceed the requirements of the U.S. Coast Guard, the Boating Industry As- sociation and the American Boat and Yacht Council in effect at the time of manufacture.

  • Page 54: Outboard Engine Fuel System

    Fuel System Typical Yamaha Engine Fuel Filters 5.2 Outboard Engine Fuel System The gasoline fuel system has one fuel tank that fills from the port gunnel. The starboard engine is supplied by the starboard fuel line and the port engine is supplied by the port fuel line. If your boat is equipped with triple engines, the center engine will be supplied by a center fuel line.
  • Page 55 Fuel System Notice: DANGER Clean fuel is especially important in fuel in- jected engines. The engine manufacturer’s recommendations for fuel filter maintenance TO REDUCE THE POSSIBILITY OF A FIRE OR EXPLOSION, must be followed exactly. MAKE SURE ALL ELECTRICAL SWITCHES ARE IN THE “OFF” POSITION BEFORE SERVICING THE FUEL SYSTEM.

  • Page 56: Fueling Instructions

    RESULT OF USE OF AN ALCOHOL BLEND IS NOT COVERED SPILLED FUEL IS DANGEROUS AND CAN YELLOW FIBERGLASS BY THE EVERGLADES WARRANTY. REFER TO THE ENGINE OR IGNITE. MAKE SURE YOU DO NOT SPILL ANY FUEL. IF FUEL MANUFACTURER OWNER’S MANUAL REGARDING FUEL IS SPILLED ON THE DECK, USE A CLOTH TO REMOVE THE FUEL REQUIREMENTS FOR YOUR ENGINES.

  • Page 57: Fuel System Maintenance

    Fuel System 5.5 Fuel System Maintenance The age of gasoline can effect engine performance. Chemical changes occur as the gasoline ages that Periodically inspect all primer bulbs, connections, can cause deposits and varnish in the fuel system clamps and hoses for leakage, damage or deterio- as well as reduce the octane rating of the fuel.
  • Page 58 THIS PAGE WAS LEFT BLANK INTENTIONALLY...

  • Page 59: Electrical System

    6.1 General windshield, windlass and power steering system. Additional fuses near the main circuit breakers Your Everglades is equipped with 120 volt AC protect continuous power circuits for the stereo and 12 volt DC electrical systems. The AC sys- memory, automatic switches for bilge pumps,...
  • Page 60 Electrical System Battery Switches, Emergency Parallel Switches, PT & STBD Voltage Sensitive Relays, Main Circuit Breakers and Continuous Power Fuse Panel The batteries should be of the size and capacity the switch if the remote switch or relay fails. The recommended by the manufacturer of your en- manual override is a yellow knob on each battery gines.
  • Page 61 Electrical System manual override is a yellow knob on each battery switch that can be pressed to manually activate the switch or rotated to reactivate remote activa- tion of the switch or to lockout the switch in the OFF position when servicing the electrical system. The normal operating position for each switch is the “Enabled”...

  • Page 62: Dc System Switch Panels

    Yamaha Command Link Plus Ignition ® Most Everglades boats are equipped with Yamaha engines and the Command Link Plus ignition key ® panels that offer the latest in technology and du- rability.
  • Page 63 Activates the pump that recirculates the water in the baitwell. Baitwell Light Activates the light in the baitwell. Reserved for additional DC accessories installed by you or your Everglades dealer. Livewell Pump Helm Switch Panel Activates the pump that supplies seawater to the livewell.
  • Page 64 Electrical System Parallel and Battery Switches in Helm Switch Panel Engine 3 (Optional) House Remotely activates the House battery switch. A Remotely activates the Center Engine battery switch. A red LED light in the switch glows when red LED light in the switch glows when the bat- the battery switch it controls is activated.
  • Page 65 Electrical System windshield. Move the switch in the opposite direc- tion to raise the windshield. The switch returns to the OFF position when it is released. Wiper/Washer A three position switch that activates the optional windshield wiper and washer. Press the lower position to turn the wiper OFF.
  • Page 66 Electrical System Spot Light (Optional) Located in the helm. Controls the spot light that is mounted on the hardtop. It is protected by a fuse located in the accessory fuse panel in the helm. Refer to the spot light owner’s manual for details on operating the control pad.

  • Page 67: Dc System Circuit Protection

    Electrical System switch OFF immediately when pumping is complete. The pump circuit is protected by a fuse located in the accessory fuse panel behind the helm. Coast Guard regulations require that the key be removed from the switch whenever the discharge pump is not being operated.
  • Page 68 Electrical System CONTINUOUS POWER FUSE PANEL MAIN CIRCUIT BREAKERS Main Circuit Breakers and Continuos Power Fuse Panel Main Circuit Breakers Main Protects the circuit that supplies 12 volt current to DC Power is distributed to the head compart- the head compartment DC breaker Panel and ac- ment DC breaker panel, accessory fuse panels, cessory fuse panels behind the helm.

  • Page 69: Bonding System

    Electrical System circuits that are always active and not turned off by the battery switches. The continuous power circuits are always supplied current when the House batteries are connected. The fuses in this panel provide continuous power and protect the circuits for the fol- lowing accessories: Stereo Memory Protects the circuit that supplies continuous 12...

  • Page 70: Ac Electrical System

    Electrical System The engine bonding system is connected to the DC ground and the earth ground wire for the AC elec- trical system for the battery charger. It provides a path to the safety earth ground in the event of a fault in the shore earth ground connection.

  • Page 71: Electrical System Maintenance

    Electrical System WARNING KEEP CHILDREN AWAY FROM ANY ELECTRICAL CABLES OR EQUIPMENT. UNDETECTED FAULTS IN THE AC BATTERY CHARGING SYSTEM COULD CAUSE THE WATER AROUND THE BOAT TO BECOME ENERGIZED. THIS COULD CAUSE A SEVERE SHOCK OR EVEN DEATH TO SOMEONE IN THE WATER NEAR THE BOAT. NEVER SWIM OR ALLOW SWIMMING AROUND THE BOAT WHEN THE BATTERY CHARGING SYSTEM IS ACTIVATED BY THE SHORE POWER CONNECTION.
  • Page 72 Electrical System The battery posts should be kept free of corrosion. CAUTION Remove the cables and clean the posts and cable clamps with a battery post cleaner or sandpaper WHEN REPLACING LIGHT BULBS IN MARINE LIGHT FIXTURES, as required. Coating the battery posts and cable ALWAYS USE A BULB WITH THE SAME RATING AS THE clamps with Teflon or Silicone grease will protect ORIGINAL.

  • Page 73: Fresh Water System

    ATTEMPT TO PUMP IT OUT YOURSELF. WATER AND WASTE PUMPS ARE NOT DESIGNED TO PUMP FUEL AND A FIRE OR EXPLOSION COULD RESULT. CONTACT YOUR DEALER OR THE EVERGLADES CUSTOMER SERVICE DEPARTMENT FOR ASSISTANCE IN HAVING THE FUEL PROFESSIONALLY REMOVED AND COMPONENTS OF THE FRESH WATER SYSTEM REPLACED AS NECESSARY.
  • Page 74 Fresh Water System Work Station Sink and Fresh Water Shower The sink in the cockpit work station is equipped with fresh and raw water. A spray head/shower on a retractable hose is mounted in a recess next to the faucet. To use the fresh water spray head, pull it out of the recess and make sure the Fresh Water switch is on.

  • Page 75: Fresh Water System Maintenance

    Fresh Water System 7.3 Fresh Water System Maintenance Information supplied with water system compo- nents by the equipment manufacturers is included with this manual. Refer to this information for additional operation and service data. Routine Maintenance The following items should be done routinely to maintain your fresh water system: •...
  • Page 76 THIS PAGE WAS LEFT BLANK INTENTIONALLY...

  • Page 77: Raw Water System

    If this procedure doesn’t work, contact your Everglades dealer. Closing the thru-hull valves before the boat is hauled from the water will help to eliminate air Raw Water and Fresh Water locks in raw water systems.

  • Page 78: Livewell And Baitwell

    Raw Water System Washdown Hose Connector The raw water washdown hose connection is lo- cated on the port side of the cockpit below the gunnel and uses a standard garden hose connec- tor. It is equipped with a valve that allows the flow of water to be turned on or off.

  • Page 79: Raw Water System Maintenance

    Raw Water System the pump. When the water level reaches the overflow, it will begin to circulate. When the recirculating feature for either well is activated by the Recirc switches, a separate pump will recirculate and aerate the water that is in the well without drawing additional seawater into the system.
  • Page 80 Raw Water System Intake Scoop Strainer CAUTION A thru-hull water intake scoop and strainer pro- vides seawater to the raw water manifold. This SHOULD A HOSE RUPTURE, TURN THE PUMP OFF IMMEDIATELY. strainer is located on the hull bottom and must be ALWAYS CLOSE THE THRU-HULL VALVE WHEN PERFORMING kept free of mud, weeds and other debris.

  • Page 81: Drainage Systems

    9.2 Cockpit and Deck Drainage Cockpit Scupper Drains Your Everglades has four scupper drains located in the rear of the cockpit below a small hatch. The scuppers drain to thru-hull fittings in each trim tab Typical Scupper Drains and Drain Rail...

  • Page 82: Hardtop And Tower Drains

    Drainage Systems 9.3 Hardtop and Tower Drains There is a hole drilled in the leg bases on the frame to prevent water from being trapped within the legs. Additional drain holes are drilled in the tubing to drain other areas as required. Always make sure the leg drain holes are clear when the boat is laid up for the winter.

  • Page 83: Drainage System Maintenance

    Drainage Systems After showering, it is important to let the cold water flow for a period of time to flush the drain- age system of soap residue. Make sure to inspect the sump system regularly and keep the sump components and pump strainer clean. The sump pump and switch are located below a hinged hatch in the head compartment sole.
  • Page 84 THIS PAGE WAS LEFT BLANK INTENTIONALLY...

  • Page 85: Ventilation System

    Chapter 10: VENTILATION SYSTEM 10.1 Head Compartment Ventilation Door & Vents Ventilation to head compartment is provided by vents in the door and an opening port window. The door itself is held in the open position by an automatic magnetic latch. Make sure the door is fully latched in the closed position before operat- ing the boat above idle speed.

  • Page 86: Windshield Ventilation

    Ventilation System 10.2 Windshield Ventilation The windshield can be lowered to provide ventila- tion at the helm and improved visibility. The wind- shield is raised and lowered by hydraulic cylinders activated by an electric hydraulic pump in the head compartment. The system is controlled by the Windshield switch in the hardtop switch panel.

  • Page 87: Maintenance

    Ventilation System 10.4 Maintenance • Keep the windshield slide tracks clean. Peri- odically coating the tracks with silicone spray • Periodically lubricate all hinges and latch as- will reduce friction and keep the windshield semblies with a light oil. sliding smoothly. •...
  • Page 88 THIS PAGE WAS LEFT BLANK INTENTIONALLY...

  • Page 89: Exterior Equipment

    Any problems should be corrected immediately. Typical Cleat in the Mooring Position WARNING EVERGLADES BOATS ARE NOT EQUIPPED WITH HARDWARE DESIGNED FOR TOWING PURPOSES. THE MOORING CLEATS ARE NOT TO BE USED FOR TOWING ANOTHER VESSEL OR HAVING THIS BOAT TOWED.
  • Page 90 Exterior Equipment A. Raw Water Faucet E. Anchor Line Cleat B. Coiled Washdown Hose Compartment F. Bow Roller Assembly C. Chain Binder G. Rope Locker D. Windlass H. Windlass Switch The chain binder is accessed by opening the hatch secures the hatch in the closed position. Always and is designed to connect to a link in the anchor make sure the hatch is closed and latched before chain when the anchor is hauled in.
  • Page 91 Exterior Equipment to open the hatch and rinse the windlass and all hardware with freshwater when the boat is washed at the end of each day. The rope locker is designed for the anchor line and not for storing anchors or additional anchor lines. Do not store anchors or any heavy objects in the locker.

  • Page 92: Hull

    Exterior Equipment 11.3 Hull Engine Mounting System and Swim Platform Your Everglades is equipped with an engine mounting system that is integrated into the hull and stringer system that is designed to distribute the stresses of engine weight and thrust through- out the entire hull.

  • Page 93: Transom Door

    Exterior Equipment Some large hatches in the cockpit sole and deck are secured with special flush mounted, twist lock latches with handles that store flush in the latch in the open or latched position. There is a large red dot in some handles that indicate that the latch is in the open position and the hatch is not secure.
  • Page 94 Exterior Equipment Notice: Periodically inspect the transom door fittings for wear, damage or loose fit. Any problems should be inspected and corrected immedi- ately. WARNING THE TRANSOM DOOR SHOULD BE CLOSED AND PROPERLY LATCHED WHENEVER THE ENGINES ARE RUNNING. NEVER OPEN THE TRANSOM DOOR WHILE UNDERWAY OR IN ROUGH SEA CONDITIONS.
  • Page 95 Exterior Equipment WARNING OPERATING THE BOAT UNDER POWER WITH THE DIVE DOOR OPEN MAY ALLOW PERSONS TO FALL OVERBOARD AND INTO BOAT PROPELLERS OR TO BE LOST IN OPEN WATER. ALWAYS CHECK TO MAKE SURE THE DIVE DOOR IS PROPERLY CLOSED AND LATCHED BEFORE STARTING THE ENGINES.
  • Page 96 Exterior Equipment Aft Bench Seats Folded Aft Bench Seats in the Seat Position Stern Cooler/Fishbox and Prepped Bait box An insulated cooler/fishbox is located in the tran- som at the rear of the cockpit. A flush, “push to close” latch secures the hatch in the closed posi- tion and two straps hold the hatch in the open position.
  • Page 97 Exterior Equipment The latch handle shafts are threaded to pull the pawl against cockpit sole, securing the hatch and compressing the gasket for a more watertight seal. Always make sure the hatch is closed with the latches in the secured position and the handles folded flush before operating the boat above idle speed.
  • Page 98 Exterior Equipment To use the seat, release the latch then pull the top of the seat toward the cockpit. The bottom of the seat slides in a track and two side supports move out with the seat as it folds out. The seat automatically locks into the seating position when the cushion reaches the full down position.
  • Page 99 Exterior Equipment A molded recess on each side of the seat base is designed for fire extinguishers. The recessed mounting location keeps the fire extinguishers out of the way and readily available. Cooler Compartment A 94 quart cooler is mounted in a special compart- ment at the front of the seat base below the helm seats.

  • Page 100: Rod Lockers

    Exterior Equipment The bow seat cushions are removable and are secured to the hatches with snaps. The cushions should be removed and stored in the head compart- ment or another safe location out of the weather when the boat is not being used. Casting Deck, Sun Lounge and Table A retractable table con- verts the bow area into...

  • Page 101: Center Console And Helm

    There are also fuse panels that provide protection for equipment installed by Everglades or other equipment added by you or your dealer. The rear of the helm is hinged at the bottom and opens to provide access to service control and steering system components.
  • Page 102 Exterior Equipment To open the helm station, make sure the engines are not running and hold the helm in the closed position while another person releases the latches that secure the helm inside the head compart- ment. The latches are located behind the storage compartment doors in the rear head compartment bulkhead.
  • Page 103 Refer to the Ventilation chapter for instructions on operating the windshield. The windshield wiper and washer is standard on your Everglades boat. A special lockout mecha- nism prevents the windshield wiper or washer from activating unless the windshield is in the full up (closed) position.

  • Page 104: Hardtop Standard Hardtop

    355 CC Hardtop with Optional Upper Station Hardtops and hardtops equipped with the optional upper station are not designed to support the additional weight of heavy items like a life raft.

  • Page 105: Upper Station (Optional)

    If you intend to add equipment or make modifications to the hard top, you should contact Everglades Customer Service or your dealer to make sure the equipment you would like to add or the intended modification will not void the warranty on the top.
  • Page 106 Exterior Equipment WARNING ACCIDENTALLY STEPPING INTO THE UPPER STATION ACCESS HATCH OPENING CAN CAUSE SEVERE INJURY TO THE OPERATOR OR CREW. ALWAYS MAKE SURE THE UPPER STATION ACCESS HATCH IS CLOSED AND LATCHED WHENEVER PEOPLE ARE IN THE UPPER STATION. The upper station seats are equipped with a flip up bolster to provide more room between the seats and the helm.
  • Page 107 Exterior Equipment To lower the Upper helm station: 1. Before raising or lowering the upper station, the boat should be either on a cradle, the trailer or moored to a dock in a safe location close to the haul out where rough water, wind or boat wakes are not a problem.

  • Page 108: Aftermarket Hardtop Or Tower

    Do not use pliers the installation of a fabrication not installed at or tools to tighten the hand bolts. the Everglades factory. If you intend to install an aftermarket hardtop, upper helm station or Notice:...

  • Page 109: Interior Equipment

    Chapter 12: INTERIOR EQUIPMENT Head Compartment 12.1 Head Compartment and Berth The head compartment is equipped with a fresh water sink and faucet that converts to a shower by pulling the faucet out of the base. An acrylic panel folds down above the marine toilet to provide a seat while showering.
  • Page 110 Interior Equipment Daylight and ventilation is provided by an opening port window and vents in the cabin door. There are also 12 volt lights in the headliner and in the berth area that are activated by a switch near the door. There are two large doors and a removable hatch in the rear bulkhead.

  • Page 111: Marine Head System

    Interior Equipment A storage compartment is located below the sink. The hydraulic system that raises and lowers the windshield is located in this compartment. There is another storage compartment and a berth for- ward of the sink. The electric pedestal for the cockpit table is mounted above the forward section of the berth.
  • Page 112 Interior Equipment To operate the overboard discharge pump, make sure the thru-hull valve in the bilge and the dis- charge valve near the pump are open. Then turn the key switch in the panel to the ON position. Press and hold the momentary button to activate the pump.

  • Page 113: Routine Maintenance

    The 355 CC is equipped blister warranty. with a large anode on the transom that is con- nected to the bonding system.
  • Page 114 Contact and chemical cleaners are not recommended your dealer or Everglades Customer Service for because they can damage or dull the gelcoat, the proper size and type of anodes to be used and reducing its life and making it more susceptible the specific installation procedure.
  • Page 115 Routine Maintenance The following guidelines will help keep stain- when the boat is washed and will not be rinsed by less steel looking good for many years. the rain. Consequently, the aluminum just below • Clean stainless steel frequently (daily in salt the top is more likely to become pitted than the ex- or polluted environments) with mild soap and posed aluminum on the structure.
  • Page 116 Routine Maintenance the salt and become corroded than the exposed Notice: You should contact Everglades Customer areas on the structure. Make sure the aluminum Service before making any modifications to in this area is washed frequently with soap and water and rinsed thoroughly. Pay particular at- aluminum fabrications.

  • Page 117: Upholstery, Canvas And Enclosures

    Routine Maintenance provide additional information on fuel degradation • Food grease and oily stains - Spray immediately and fuel stabilizers recommended for your engine. using either Fantastik Cleaner® or Tannery Car Care Cleaner®, wiping with a soft cloth. Take In many states, most gasoline is blended with care not to extend the area of contamination ethanol alcohol.
  • Page 118 If you have any questions about extend the life of the curtains. the clear curtains used on your boat, please con- tact your dealer or Everglades Customer Service. Vinyl curtains should be stored either rolled or flat, without folds or creases. Folding the curtains...

  • Page 119: Interior

    Routine Maintenance 13.3 Interior For heavy duty cleaning, use a mixture of water and Murphy’s Oil Soap or a solution of 10% white The cabin or head interior can be cleaned just vinegar and water to clean the wood and wipe it like you would clean a home interior.
  • Page 120 THIS PAGE WAS LEFT BLANK INTENTIONALLY...

  • Page 121: Seasonal Maintenance

    Moisture from condensation in Everglades dealer. the fuel tank can reach such concentrations that it becomes heavy enough to settle out of •...
  • Page 122 FOR THE HULL. HULL DAMAGE RESULTING FROM IMPROPER Supporting The Boat For Storage CRADLE OR TRAILER SUPPORT IS NOT COVERED BY THE EVERGLADES WARRANTY. A trailer, elevating lift, well-made cradle or proper blocking is the best support for your boat during storage.

  • Page 123: Winterizing

    Seasonal Maintenance • Remove the batteries and store in a cool of commercially available non toxic, fresh water place. Clean using clear, clean water. Be sure system antifreeze. After draining the fresh water the batteries have sufficient water and clean tank, lines, filters and water heater, pour the an- terminals.
  • Page 124 Refer to the Raw Water System chapter for ad- turer’s winterizing procedures located in ditional information on the raw water system. your engine owner’s manuals or contact an Everglades dealer. Marine Toilet Hardtop The marine toilet must be properly winterized by following the manufacturer’s winterizing instruc-...

  • Page 125: Recommissioning

    Seasonal Maintenance 14.3 Recommissioning Special Notes Prior To Winter Storage If the boat will be in outside storage, properly sup- port a storage cover and secure it over the boat. It CAUTION is best to have a frame built over the boat to sup- port the canvas.
  • Page 126 Seasonal Maintenance After Launching: • Carefully check all water systems and the engine bolts for leaks. Operate each system one at a time checking for leaks and proper operation. • Check the bilge pump manual and automatic switches. • When each engine starts, check the cooling system port below the engine cowling for a strong stream of water.

  • Page 127: Appendix A: Schematics

    Appendix A: SCHEMATICS                      ...
  • Page 128 THIS PAGE WAS LEFT BLANK INTENTIONALLY...

  • Page 129: Appendix B: Glossary Of Terms

    Appendix B: GLOSSARY OF TERMS Bow Rail: Knee high rails of solid tubing to aid ft: In, near or toward the stern of a boat. in preventing people from falling overboard. Aground: A boat stuck on the bottom. Bridge: The area from which a boat is steered and controlled.
  • Page 130 Glossary of Terms Grab Rail: Hand-hold fittings mounted on cabin eck: The floor-like platform of a boat that tops or sides for personal safety when moving covers the hull. around the boat, both on deck and below. Displacement: The volume of water displaced by Ground Tackle: A general term including anchors, the hull.
  • Page 131 Glossary of Terms Length On The Waterline (l.w.l.): A length mea- Pile or Piling: A long column driven into the bot- surement of a boat at the waterline from the stern tom to which a boat can be tied. to where the hull breaks the water near the bow. Pitching: The fore and aft rocking motion of a Limber Hole: A passage cut into the lower edges boat as the bow rises and falls.
  • Page 132 Glossary of Terms Scupper: An opening in the hull side or transom affrail: Rail around the rear of the cockpit. of the boat through which water on deck or in the cockpit is drained overboard. Thru-hull: A fitting used to pass fluids (usually Seacock: Safety valves installed just inside the water) through the hull surface, either above or below the waterline.

  • Page 133: Appendix C: Maintenance Log

    Appendix C: MAINTENANCE LOG Service/Repairs Date Dealer Hours...

  • Page 134: Maintenance Schedule And Log

    Maintenance Schedule and Log MAINTENANCE LOG Date Dealer Service/Repairs Hours...
  • Page 135 Maintenance Schedule and Log MAINTENANCE LOG Date Dealer Service/Repairs Hours...
  • Page 136 Maintenance Schedule and Log MAINTENANCE LOG Date Dealer Service/Repairs Hours...

  • Page 137: Boating Accident Report

    BOATING ACCIDENT REPORT Appendix D:                                       ...
  • Page 138 Boating Accident Report                                      ...
  • Page 139 Boating Accident Report                                                  ...
  • Page 140 THIS PAGE WAS LEFT BLANK INTENTIONALLY...

  • Page 141: Appendix E: Float Plan

    Appendix E: FLOAT PLAN Everglades recommends filling out a float plan each time you use your boat for an off- shore day trip or a long cruise. Leave this information with a responsible person ashore, like a close friend or relative that you know well.
  • Page 142 THIS PAGE WAS LEFT BLANK INTENTIONALLY...

  • Page 143: Troubleshooting Guide

    Appendix F: TROUBLESHOOTING GUIDE PROBLEM CAUSE AND SOLUTION CONTROL SYSTEMS Hydraulic Steering is slow to respond & erratic and/or the • Steering system is low on fluid. Fill and bleed system. • Steering system has air in it. Fill and bleed system. steering wheel feels bumpy. • A component in the steering system is binding. Check and adjust or repair binding component.
  • Page 144 Troubleshooting Guide PROBLEM CAUSE AND SOLUTION ENGINE PROBLEMS An engine is running too hot. • The engine raw water pick up strainer is clogged with marine growth. Clean pick up. • The engine raw water pump impeller is worn or damaged. Repair the pump.
  • Page 145 Troubleshooting Guide PROBLEM CAUSE AND SOLUTION ACCESSORY PROBLEMS The livewell pump runs, but does not pump water. • The intake scoop strainer for the raw water system is clogged with weeds or debris. Back down the boat to clear debris or clean the scoop strainer.
  • Page 146 Troubleshooting Guide PROBLEM CAUSE AND SOLUTION ACCESSORY PROBLEMS The automatic switch on the bilge pump does not activate • The fuse or circuit breaker for the automatic switch has tripped or blown. Replace the fuse or reset the circuit the pump . breaker.
  • Page 147 CAUSE AND SOLUTION...
  • Page 148 All Channels Lead to Everglades Boats Everglades Boats 544 Air Park Road Edgewater, Florida 32132...

This manual is also suitable for:

355 ccx

Table of Contents