Page 3
Your selection of our product is a demon- stration of your trust in our company name. Furthermore, it exemplifies your desire to own an automobile that will be as easy as possible to operate and provide years of service. Your Mercedes-Benz represents the efforts of many skilled engineers and craftsmen.
Operator’s Manual ... 10 Service and warranty information .. 10 Important notice for California retail buyers and lessees of Mercedes-Benz automobiles ... 11 Maintenance ... 12 Roadside Assistance ... 12 Change of address or ownership... 12 Operating your vehicle outside the USA or Canada...
Page 5
Contents Safety and Security ... 63 Occupant safety... 64 Air bags ... 66 Occupant Classification System... 71 Seat belts ... 76 Children in the vehicle... 79 Panic alarm ... 83 Activating ... 83 Deactivating ... 83 Driving safety systems... 84 ABS ...
Page 6
Control system ... 121 Multifunction display... 121 Multifunction steering wheel... 122 Menus ... 124 Standard display menu ... 127 AMG menu ... 128 AUDIO menu ... 133 NAV* menu... 135 Vehicle status message memory menu ... 135 Settings menu... 136 Trip computer menu...
Page 7
Contents Audio system ... 193 Audio and telephone*, operation . 193 Operating safety... 193 Operating and display elements ... 194 Button and soft key operation ... 196 Operation ... 196 Radio operation... 199 Introduction to satellite radio* ... 203 CD mode ... 208 GSM network phones...
Page 8
At the gas station ... 291 Refueling ... 291 Check regularly and before a long trip... 292 Engine compartment ... 294 Hood ... 294 Engine oil ... 296 Transmission fluid level*... 300 Coolant level ... 300 Windshield washer system and headlamp cleaning system*...
Page 9
Contents Replacing wiper blades ... 406 Placing wiper arms in vertical position ... 406 Removing wiper blades ... 407 Installing wiper blades... 407 Flat tire ... 408 Preparing the vehicle... 408 Sealing tires with TIREFIT ... 408 Mounting the spare wheel... 414 MOExtended system*...
Product information Please observe the following in your own best interest: We recommend using Genuine Mercedes-Benz Parts as well as conversion parts and accessories explicitly approved by us for your vehicle model. We have tested these parts to determine their reliability, safety and special suitability for Mercedes-Benz vehicles.
Vehicle damage caused by failure to follow instructions is not covered by the Mercedes-Benz Limited Warranty. Your vehicle may have some or all of the equipment described in this manual.
Under California law you may be entitled to a replacement of your vehicle or a refund of the purchase price or lease price, if Mercedes-Benz USA, LLC and/or its authorized repair or service facilities fail to fix one or more substantial defects or mal-...
Calls to the toll-free Roadside Assistance number 1-800-FOR-MERCedes (in the USA) 1-800-387-0100 (in Canada) will be answered by Mercedes-Benz Customer Assistance Representatives 24 hours a day, 365 days a year. For additional information refer to the...
Certain Mercedes-Benz models are available for delivery in Europe under our European Delivery Program. For details, consult an authorized Mercedes-Benz Center or write to:...
Here you will find all the information you need for your first drive. You should read this section first if this is your first Mercedes-Benz vehicle or if you are rent- ing or borrowing this vehicle. Safety and Security Here you will find descriptions of the safety and security features of your vehicle.
Symbols Trademarks: ® is a registered trademark of DaimlerChrysler. ® HomeLink is a registered trademark of Prince, a Johnson Controls Company. SIRIUS and related marks are trade- marks of SIRIUS Satellite Radio Inc. The following symbols are found in this Operator’s Manual: Optional equipment is identified with an asterisk.
Contact an authorized Mercedes-Benz Center for repairs or modifications to electronic components. Other improper work or modifications on the vehicle could also have a negative impact on the operating safety of the vehicle.
If you should experience a problem with your vehicle, particularly one that you believe may affect its safe operation, we urge you to immediately contact an authorized Mercedes-Benz Center to have the problem diagnosed and corrected if required. If the matter is...
If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Mercedes-Benz USA, LLC. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Vehicle data recording Information regarding electronic recording devices (Including notice pursuant to California Code § 9951) Please note that your vehicle is equipped with devices that can record vehicle systems data and, if equipped with the Tele Aid* system, may transmit some data in certain accidents. This information helps, for example, to diagnose vehicle systems after a collision and to continuously improve vehicle safety.
At a glance Exterior view Cockpit Instrument cluster Multifunction steering wheel Center console Overhead control panel Storage compartments Door control panel...
Page 28
Item Page 1 Multifunction display with: Main odometer Trip odometer 120, Automatic transmission*: Gear range indicator Automatic transmission*: Program mode indicator Outside temperature indicator (or digital speed- ometer when selected) Set speed for cruise control 2 Tachometer with: ? Engine malfunction indicator lamp, USA only ±...
At a glance Multifunction steering wheel Item Page 1 Multifunction display Operating control system 2 Selecting a submenu or setting the volume: Press button æ up/to increase ç down/to decrease 3 Telephone*: Press button s to take a call to dial to redial t to end a call to reject an incoming...
Center console Upper part Item Page 1 Cup holder 2 Audio system COMAND* system (see separate operating instructions) 3 AIRSCARF* switch, passenger-side 4 Seat heating* switch, passenger-side 5 Central unlocking switch 6 Hazard warning flasher switch 7 Central locking switch Alarm system indicator lamp At a glance...
At a glance Door control panel Item Page 1 Inside door handle 2 Power window switch for opening/closing passenger-side window 3 Power window switch for opening/closing driver’s side window...
Getting started Unlocking The “Getting started” section provides an overview of the vehicle’s most basic func- tions. First-time Mercedes-Benz owners should pay special attention to the infor- mation given here. If you are already familiar with the basic functions described here, the “Controls in detail”...
Enter the vehicle and insert the SmartKey in the starter switch. Opening a door causes its window to open slightly. It will fully close when the door is shut. A side window will not work if it is blocked with ice or if the battery needs charging. If you cannot shut a door, do not force it or you could damage the door or the side window.
Page 39
Getting started Unlocking When you switch on ignition, the indicator and warning lamps (except high beam headlamp indicator lamp and turn signal indicator lamps unless activated) in the instrument cluster come on. The indicator and warning lamps (except high beam headlamp indicator lamp and turn signal indicator lamps if activated) will go out when the engine is running.
Adjusting Warning! All seat, head restraint, steering wheel, and rear view mirror adjustments, as well as fas- tening of seat belts, must be done before the vehicle is put into motion. Seats The seats can be adjusted either manually or electrically, depending on the vehicle’s equipment.
Page 41
Getting started Adjusting Warning! When leaving the vehicle, always remove the SmartKey from the starter switch, take it with you, and lock the vehicle. Even with the SmartKey removed from the starter switch, the power seats* can be op- erated when the respective door is open. Therefore, do not leave children unattended in the vehicle, or with access to an unlocked vehicle.
Page 42
Seat fore and aft adjustment Pull handle 1. Slide the seat to the desired position. Allow handle 1 to reengage with an audible click. Check for proper engagement before driving. Seat height Pull or push handle 2 up or down and adjust the seat height until your legs are slightly supported.
Page 43
Getting started Adjusting The memory function* ( page 107) lets you store the settings for power seats*, steering wheel adjustment (electrical)*, and exterior rear view mirrors. Seat fore and aft adjustment Press the horizontal switch forward or backward in direction of arrows 1. Seat height Press the horizontal switch up or down in direction of arrows 2 and adjust the...
Steering wheel Warning! Do not adjust the steering wheel while driv- ing. Adjusting the steering wheel while driv- ing, or driving without the steering wheel adjustment feature locked could cause the driver to lose control of the vehicle. When leaving the vehicle, always remove the SmartKey from the starter switch, take it with you, and lock the vehicle.
Page 45
Getting started Adjusting Steering wheel adjustment, electrical* The steering wheel adjustment stalk is located on the lower left of the steering column. 1 Adjusting steering wheel, in or out 2 Adjusting steering wheel, up or down Switch on the ignition ( page 37). Open the driver’s door.
Page 46
Warning! You must make sure no one can become trapped or injured by the moving steering wheel when the easy-entry/exit feature is activated. To cancel steering wheel movement, do one of the following: Move steering wheel adjustment stalk* ( page 44). Press one of the memory position but- tons* or the memory button M* ( page 107).
Getting started Adjusting Warning! Let the system complete the adjustment procedure before setting the vehicle in mo- tion. All steering wheel adjustment must be completed before setting the vehicle in mo- tion. Driving off with the steering wheel still adjusting could cause the driver to lose con- trol of the vehicle.
Page 48
The buttons are located on the lower part of the center console. 1 Driver’s side exterior rear view mirror button 2 Adjustment button 3 Passenger-side exterior rear view mirror button Switch on the ignition ( page 37). Press button 1 for the driver’s side exterior rear view mirror or button 3 for passenger-side exterior rear view mirror.
Getting started Driving Warning! Make sure that absolutely no objects are ob- structing the pedal’s range of movement. Keep the driver’s footwell clear of all obsta- cles. If there are any floormats or carpets in the footwell, make sure the pedals still have sufficient clearance.
Page 50
Warning! Never let more people ride in the vehicle than there are seat belts available. Be sure everyone riding in the vehicle is correctly restrained with a separate seat belt. Never use a seat belt for more than one person at a time.
Page 51
Do not bleach or dye seat belts as this may severely weaken them. In a crash, they may not be able to provide adequate protection. Damaged seat belts or seat belts that were highly stressed in an accident must be replaced. Contact an authorized Mercedes-Benz Center.
Starting the engine Warning! Inhalation of exhaust gas is hazardous to your health. All exhaust gas contains carbon monoxide (CO), and inhaling it can cause un- consciousness and possible death. Do not run the engine in confined areas (such as a garage) which are not properly ventilated.
Page 53
Get a jump start ( page 426). If the engine does not start after several starting attempts, there could be a mal- function in the engine electronics or in the fuel supply system. Contact an authorized Mercedes-Benz Center or call Roadside Assistance.
Parking brake Warning! When leaving the vehicle, always remove the SmartKey from the starter switch, take it with you, and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Children could release the parking brake, which could result in an accident and/or serious personal injury.
Page 55
Getting started Driving Once the vehicle is in motion, the automatic central locking system engages and the locking knobs drop down. The automatic door lock feature can be deacti- vated ( page 146). You can open a locked door from the inside. Open door only when conditions are safe to do Manual transmission Depress the brake pedal.
Switching on headlamps Low beam headlamps The exterior lamp switch is located on the dashboard to the left of the steering wheel. Exterior lamp switch 1 Off 2 Low beam headlamps on Turn the exterior lamp switch to position B. The low beam headlamps come on.
Turn the windshield wipers on again. If the windshield wipers fail to function at all with the combination switch in position I, set the combination switch to the next higher wiper speed have the windshield wipers checked at the nearest authorized Mercedes-Benz Center...
Page 58
Switching on windshield wipers Turn the combination switch to the desired position depending on the intensity of the rain. 0 Windshield wipers off Intermittent wiping II Normal wiper speed III Fast wiper speed Intermittent wiping Vehicles with rain sensor*: Do not leave windshield wipers on an intermit- tent setting when the vehicle is taken to an auto- matic car wash or during windshield cleaning.
Unburned gasoline may have entered the catalytic converter and damaged it. Give very little gas. Have the problem repaired by an au- thorized Mercedes-Benz Center as soon as possible. The coolant temperature is above 248°F (120°C) The coolant is too hot and is no longer cooling the engine.
Parking and locking You have now completed your first drive. You have properly stopped and parked your vehicle. End your drive as follows. Warning! Vehicles with manual transmission: Wait until the vehicle is stationary before re- moving the SmartKey from the starter switch.
Page 61
Getting started Parking and locking 1 Parking brake lever Pull up parking brake lever 1 firmly. When the ignition is switched on or the engine is running, the brake warning lamp ; (USA only) or 3 (Canada only) in the speedometer dial comes Warning! Getting out of your vehicle with the gear se- lector lever* not fully engaged in position P...
This can damage the seat belt and impair the effectiveness of the seat belt, and/or cause damage to the door and/or door trim panel. Such damage is not covered by the Mercedes-Benz Limited Warranty. Damaged seat belts must be replaced. Contact an authorized Mercedes-Benz Center.
Getting started Parking and locking Locking Warning! To prevent possible personal injury, always keep hands and fingers away from the door openings when closing the doors. Be especially careful when small children are around. Before closing doors, make sure there is no possibility of someone getting caught in a door during closing.
Safety and Security Occupant safety In this section you will learn the most important facts about the restraint system components of the vehicle. Seat belts ( page 76) Child restraints ( page 80) Additional protection potential provided by Supplemental Restraint System (SRS) with Air bags ( page 66) Air bag control unit (with crash...
Page 66
Mercedes-Benz Center. Safety and Security Occupant safety If it is necessary to modify an air bag system to accommodate a person with disabilities, contact your local authorized Mercedes-Benz Center or call our Customer Assistance Center at 1-800-FOR-MERCedes (1-800-367-6372) for details.
If you have any problems, please contact an authorized Mercedes-Benz Center. Do not lean your head or chest close to the steering wheel or dashboard. Keep hands on the outside of the steer- ing wheel rim.
Page 68
Mercedes-Benz Center at an additional cost. Please contact your local authorized Mercedes-Benz Center or call the Customer Assistance Center (in the USA) at 1-800-FOR-MERCedes (1-800-367-6372), or Customer Service (in Canada) at...
Page 69
Only use seat belts installed or supplied by an authorized Mercedes-Benz Center. Air bags and Emergency Tensioning Devices (ETDs) contain Perchlorate material, which may require special han- dling and regard for the environment.
Page 70
Warning! Only use seat covers which have been tested and approved by Mercedes-Benz for your vehicle model. Using other seat covers may interfere with or prevent the deploy- ment of the head-thorax air bags. Contact an authorized Mercedes-Benz Center for availability.
Page 71
Safety and Security Occupant safety The front air bags in this vehicle have been designed to inflate in two stages. This allows the air bag to have different rates of inflation that are based on the rate of relevant vehicle deceler- ation as assessed by the air bag control unit.
Warning! Only use seat covers which have been tested and approved by Mercedes-Benz for your vehicle model. Using other seat covers may interfere with or prevent the deploy- ment of the head-thorax air bags. Contact an authorized Mercedes-Benz Center for availability.
Page 73
Safety and Security Occupant safety Warning! If the 75 indicator lamp illumi- nates when an adult or someone larger than a small individual is in the passenger seat, have the passenger re-position himself or herself in the seat until the 75 indicator lamp goes out.
Page 74
If the 75 indicator lamp is illuminated, the passenger front air bag is deactivated and will not be deployed. If the 75 indicator lamp is not illuminated, the passenger front air bag is activated and will be deployed: in the event of certain frontal impacts if impact exceeds a preset deployment threshold independently of the head-thorax air...
Page 75
Safety and Security Occupant safety If you place a child in a forward-facing child restraint on the passenger seat, move the seat as far back as possible, use the proper child restraint recom- mended for the age, size and weight of the child, and secure child restraint with the vehicle’s seat belt according to the child seat manufacturer’s instructions.
Page 76
If the 75 indicator lamp should not illuminate, the system is not functioning. You must contact an authorized Mercedes-Benz Center before seating any child on the passenger seat. More information can be found in the “Practical hints” section ( page 358).
Safety and Security Occupant safety Seat belts The use of seat belts and infant and child restraint systems is required by law in all 50 states, the District of Columbia, the U.S. territories and all Canadian provinces. Even where this is not the case, all vehicle occupants should have their seat belts fastened whenever the vehicle is in motion.
Page 78
Only use seat belts which have been approved by Mercedes-Benz. Do not make any modifications to the seat belts. This can lead to unintended activation of the ETDs or to their failure to activate when necessary.
Page 79
Safety and Security Occupant safety Seat belts should not be worn twisted. In a crash, you would not have the full width of the seat belt to manage impact forces. The twisted seat belt against your body could cause injuries. Pregnant women should also always use a lap-shoulder belt.
When disposing of the emergency tension- ing device, our safety instructions must be followed. These are available at any authorized Mercedes-Benz Center. Safety and Security Occupant safety Children in the vehicle If an infant or child is traveling with you in...
Page 81
Safety and Security Occupant safety Do not expose the child restraint system to direct sunlight. The child restraint system’s metal parts, for example, could become very hot, and the child could be burned on these parts. If children open a door, they could injure other persons get out of the car and injure themselves or be injured by following traffic...
Page 82
A statement by the child restraint manu- facturer of compliance with these stan- dards can be found on the instruction label on the restraint and in the instruction manual provided with the restraint. When using any infant, or toddler restraint, or booster seat, be sure to carefully read and follow all manufacturer’s instructions for installation and use.
Page 83
Safety and Security Occupant safety If you place a child in a forward-facing child restraint on the passenger seat, move the seat as far back as possible, use the proper child restraint recom- mended for the age, size and weight of the child, and secure child restraint with the vehicle’s seat belt according to the child seat manufacturer’s instructions.
Panic alarm 1 Â button USA only: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Safety and Security Driving safety systems In this section you will find information on the following driving safety systems: ABS (Antilock Brake System) BAS (Brake Assist System) ® (Electronic Stability Program) Warning! The following factors increase the risk of accidents: Excessive speed, especially in turns Wet and slippery road surfaces Following another vehicle too closely...
Page 86
Braking At the instant one of the wheels is about to lock up, a slight pulsation can be felt in the brake pedal, indicating that the ABS is in the regulating mode. Keep firm and steady pressure on the brake pedal while experiencing the pulsation.
Safety and Security Driving safety systems The Brake Assist System (BAS) operates in emergency situations. If you apply the brakes very quickly, the BAS automatically provides full brake boost, thereby poten- tially reducing braking distance. Apply continuous full braking pressure until the emergency braking situation is over.
Page 88
Warning! ® Never switch off the ESP when you see the ® warning lamp v flashing in the in- strument cluster. In this case, proceed as follows: While driving off, apply as little throttle as possible. While driving, ease up on the accelera- tor.
Page 89
Safety and Security Driving safety systems Electronic traction system The electronic traction system is a ® component of ESP The electronic traction system improves the vehicle’s ability to utilize available traction, especially under slippery road conditions by applying the brakes to a spinning wheel.
Page 90
Avoid spinning of a drive wheel for an ® extended period with the ESP switched off. This may cause serious damage to the drivetrain which is not covered by the Mercedes-Benz Limited Warranty. Safety and Security Driving safety systems ®...
In case the engine cannot be started (yet the vehicle’s battery is charged), the system is not operational. Contact an authorized Mercedes-Benz Center or call 1-800-FOR-MERCedes (in the USA), or 1-800-387-0100 (in Canada). Anti-theft alarm system Once the alarm system has been armed, a...
Lock the vehicle with the SmartKey. The turn signal lamps flash three times and an acoustic warning sounds three times to indicate that the alarm system is armed. Alarm system indicator lamp 1 starts flashing. If the turn signal lamps do not flash three times and no acoustic warning sounds three times, a door or the trunk lid may not be properly closed.
Page 93
Safety and Security Anti-theft systems Arming tow-away alarm Lock your vehicle with the SmartKey. The tow-away alarm is automatically armed after about 30 seconds. When you unlock your vehicle, the tow-away protection disarms automatically. The tow-away alarm remains disarmed until you lock the vehicle again.
Controls in detail Locking and unlocking Seats Memory function* Lighting Instrument cluster Control system Manual transmission Automatic transmission* Good visibility Climate control Automatic climate control* Audio system Power windows Retractable hardtop Driving systems Loading Useful features...
Controls in detail Locking and unlocking In the “Controls in detail” section you will find detailed information on how to oper- ate the equipment installed in your vehicle. If you are already familiar with the basic functions of your vehicle, this section will be of particular interest to you.
Page 96
Have the vehicle battery and the battery connections checked ( page 422). If the SmartKey is malfunctioning, contact Roadside Assistance or an authorized Mercedes-Benz Center. Without the antenna on the left rear side of the vehicle installed, the SmartKey signaling range is considerably reduced. Hold the...
Page 97
When unlocking or locking the vehicle with the SmartKey, an acoustic signal sounds. The signal is activated at the factory. If you wish to deactivate the feature or adjust its signal volume, contact an authorized Mercedes-Benz Center. Global unlocking Press button Œ.
Page 98
Replace the batteries ( page 398). You can obtain the required batteries at any authorized Mercedes-Benz Center. If the batteries are checked within signal range of the vehicle, pressing button ‹ or Œ will lock or unlock the...
If necessary have the mechanical lock replaced. Any authorized Mercedes-Benz Center will be glad to supply you with a replacement. Opening the doors from the inside You can open a locked door from the in- side.
If the vehicle has previously been centrally locked with the SmartKey, opening a door from the inside will trigger the anti-theft alarm system. To cancel the alarm, do one of the following: Press button Œ or ‹ on the SmartKey. Insert the SmartKey in the starter switch.
Controls in detail Locking and unlocking Closing the trunk Warning! Make sure the trunk is closed when the engine is running and while driving. Among other dangers, deadly carbon monoxide (CO) gases may enter vehicle interior resulting in unconsciousness and death.
Valet locking Depending on vehicle production date, your vehicle may be equipped with a feature that per- mits separate locking and unlocking of the trunk with the mechanical key. If present, this function can permit you to deny any unauthorized person access to the trunk, e.g.
Controls in detail Locking and unlocking Trunk lid emergency release With the emergency release button, the trunk can be opened from inside the trunk. 1 Emergency release button Briefly press emergency release button 1. The trunk lid unlocks and opens slightly.
Locking and unlocking from the inside Warning! When leaving the vehicle, always remove the SmartKey from the starter switch, take it with you, and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. A child’s unsupervised access to a vehicle could result in an accident and/or serious personal injury.
Controls in detail Seats For information on seat adjustment, see “Adjusting” ( page 39). Seat heating* 1 Seat heating switch 2 Indicator lamps Red indicator lamps 2 on seat heating switch 1 show which heating level you have selected: Level Three indicator lamps on (highest level).
Lumbar support* The curvature of the seats can be adjusted to help enhance lower back support and seating comfort. 1 Upper seat curvature 2 Lower seat curvature Switch on the ignition ( page 37). Turn adjustment wheels 1 and 2 until you have reached the desired seat curvature.
Page 107
Controls in detail Seats Red indicator lamps 2 on AIRSCARF switch 1 show which heating level you have selected: Level Three indicator lamps on (highest level). Two indicator lamps on. One indicator lamp on (lowest level). No indicator lamp on. Switch on the ignition ( page 37).
Memory function* Prior to operating the vehicle, the driver should check and adjust the seat height, seat position fore and aft, and seat back- rest angle if necessary, to ensure adequate control, reach and comfort. The head re- straint should also be adjusted for proper height.
Controls in detail Memory function* Storing positions into memory Adjust the seat, on the driver’s side also the steering wheel and exterior rear view mirrors, to the desired positions ( page 39). Press memory button M. Release memory button M and press a memory position switch 2 within 3 seconds.
Relevant information can be obtained at any authorized Mercedes-Benz Center. Exterior lamp switch Exterior lamp switch 1 ‚ Standing lamps, left (turn left two stops) 2 ˆ...
Page 111
Controls in detail Lighting Low beam headlamps The low beam headlamps can be switched on and off with the exterior lamp switch us- ing the manual headlamp mode. Turn the exterior lamp switch to position B. The following lamps switch on: Low beam headlamps Tail and parking lamps License plate lamps...
Page 112
Daytime running lamp mode In Canada the daytime running lamp mode is mandatory and therefore in a constant mode. In the USA the daytime running lamp mode is deactivated by default. Activate the day- time running lamp mode using the control system, see “Setting daytime running lamp mode”...
Page 113
Controls in detail Lighting When the engine is running, and you turn the exterior lamp switch to position C or B, the manual head- lamp mode has priority over the daytime running lamp mode. The corresponding exterior lamps switch on ( page 109). Locator lighting and night security illu- mination The locator lighting and the night security...
Rear fog lamp (driver’s side only) Turn the exterior lamp switch to position C or B ( page 109). Pull out the exterior lamp switch to second stop. The front fog lamps and the rear fog lamp switch on. The yellow indicator lamp † in the exterior lamp switch comes on ( page 109).
Controls in detail Lighting Corner-illuminating front fog lamps* Corner-illuminating front fog lamps are not available for the following models: SLK 280 and SLK 350 without Bi-Xenon* headlamps SLK 280 and SLK 350 with Sport Package* SLK 55 AMG The corner-illuminating front fog lamps improve illumination of the area in the direction into which you are turning.
Switching off corner-illuminating front fog lamps The combination switch for the turn signal resets automatically after major steering wheel movements. This will switch off the corner-illuminating front fog lamps if they where activated by switching on the left or right turn signal. If the turn signal should stay on after making the turn, the turn signal and corner-illuminating front fog lamp can be...
Controls in detail Lighting Switching on hazard warning flasher Press hazard warning flasher switch 1. All turn signal lamps are flashing. With the hazard warning flasher activated and the combination switch set for either left or right turn, only the respective turn signals will operate when the ignition is switched on.
Activating Press automatic control switch 2 until it is flush to the other switches. The interior lighting switches on in darkness, when you unlock the vehicle remove the SmartKey from the starter switch open a door The interior lighting switches off automati- cally following a preset time delay.
Driving characteris- tics may be impaired. If you must continue to drive, do so with added caution. Contact an authorized Mercedes-Benz Center as soon as possible. Adjusting instrument cluster illumination Adjusting Use knobs 1 or 2 to adjust the illumina- tion brightness of the instrument cluster.
( page 26) denotes excessive engine speed. Avoid driving at excessive engine speeds, as it may result in serious engine damage that is not covered by the Mercedes-Benz Limited Warranty. To help protect the engine, the fuel supply is interrupted if the engine is operated within the red marking.
Controls in detail Instrument cluster Resetting trip odometer Make sure you are viewing the standard display menu ( page 127). If it is not displayed, press button è or ÿ repeatedly until the standard display appears in the multifunction display. Press and hold reset button J until the trip odometer is reset.
Control system The control system is activated as soon as the SmartKey in the starter switch is turned to position 1. The control system enables you to call up information about your vehicle change vehicle settings For example, you can use the control system to find out when your vehicle is next due for service, to set the language for messages in the instrument cluster...
Controls in detail Control system Multifunction steering wheel The displays in the multifunction display and the settings in the control system are controlled by the buttons on the multifunc- tion steering wheel. 1 Multifunction display Operating the control system 2 Selecting the submenu or setting the volume: Press button æ...
Page 124
It is helpful to think of the menus, and the functions within each menu, as being ar- ranged in a circular pattern. If you press button è or ÿ re- peatedly, you will pass through each menu one after the other. If you press button j or k re- peatedly, you will pass through each function display, one after the other, in...
Controls in detail Control system Menus This is what you will see when you scroll through the menus. The table below provides an overview of the individual menus.
Page 126
Menus, submenus and functions Menu 1 Standard display ( page 127) Run Flat Indicator* (Canada only) TPMS (USA only) Checking coolant temperature Digital speedometer/outside temperature Calling up maintenance service indicator Checking engine oil level (SLK 55 AMG only) AMG vehicles only. Table continued on next page.
Page 127
Controls in detail Control system Menus, submenus and functions Menu 5 Menu 6 Vehicle status message Settings memory ( page 135) ( page 136) Calling up vehicle malfunction, Resetting to factory settings warning and system status messages stored in memory Instrument cluster submenu Time/Date submenu Lighting submenu...
Standard display menu The multifunction display shows the main odometer and trip odometer. This default setting is referred to as the standard display. 1 Main odometer 2 Trip odometer If another display is shown instead of the standard display: Press button è or ÿ repeatedly until the standard display appears in the multifunction display.
The engine should not be operated with a coolant temperature above 248°F (120°C). Doing so may cause serious engine damage which is not covered by the Mercedes-Benz Limited Warranty. During severe operating conditions, e.g. stop-and-go city traffic, the coolant temperature may rise close to 248°F (120°C).
Page 130
The engine oil temperature symbol flashes if the engine oil temperature has not yet reached 80°C. During this time, avoid driving at full engine speed. Use buttons k or j to select the following functions in the AMG menu: Function Page Vehicle supply voltage RACETIMER...
Page 131
Controls in detail Control system Press button j repeatedly until the RACETIMER appears in the multifunction display. 1 Gear indicator 2 RACETIMER 3 Lap number You can start the RACETIMER when the engine is running or the starter switch is in position 2 ( page 37).
Page 132
Saving lap time and starting a new lap You can save up to nine laps. Press button ç while the timer is running. The intermediate time will be shown for 5 seconds. Press button ç within 5 seconds. The intermediate time shown will be saved as a lap time.
Page 133
Controls in detail Control system Overall analysis These functions are only available if you have saved at least one lap and have stopped the RACETIMER. Press button è or ÿ repeatedly until the AMG menu appears in the multifunction display. Press button j repeatedly until the overall analysis appears in the multifunction display.
AUDIO menu The functions in the AUDIO menu operate the audio equipment which you currently have turned on. If no audio equipment is currently switched on, the message appears in the AUDIO OFF multifunction display. The following functions are available: Function Page Selecting radio station...
Page 135
Controls in detail Control system Selecting satellite radio station* The Sirius satellite radio is treated as a radio application. Select satellite radio with the corre- sponding soft key (SAT) in the radio menu. 1 SAT mode and preset number 2 Channel name or number Press button j or k repeatedly until the desired channel is found.
Controls in detail Control system If conditions have occurred causing status messages to be recorded, the number of messages appears in the multifunction dis- play: 1 Number of recorded status messages Press button j or k. The stored messages will now be dis- played in the order in which they have occurred.
Page 138
Press the reset button J on the instrument cluster ( page 26) for approximately 3 seconds. The request to press the reset button J once more to confirm appears in the multifunction display. Press the reset button J once more. The functions of all submenus will be reset to the factory settings.
Page 139
Controls in detail Control system The table below shows what settings can be changed within the various submenus. Instrument cluster Time/Date ( page 139) ( page 141) Selecting digital speed- Synchronizing time and ometer display mode date with head unit* Selecting language Setting the time Selecting display (speed...
Page 140
Instrument cluster submenu Access the Instr. Cluster submenu via Settings menu. Use the Instr. Cluster submenu to change the instrument cluster display settings. The following functions are available: Function Page Selecting speedometer display mode Selecting language Selecting display (speed display or outside temperature) for status indicator Selecting digital speedometer display...
Page 141
Controls in detail Control system Available languages: German English French Italian Spanish Dutch Danish Swedish Portuguese Turkish Selecting display (speed display or outside temperature) for status indicator Move the selection marker with button æ or ç to the Instr. Cluster submenu.
Page 142
Time/Date submenu Access the Time/Date submenu via the Settings menu. Use the Time/Date sub- menu to change the instrument cluster display settings. The following functions are available: Function Page Time and date synchronization with head unit* Setting the time Setting the date Time and date synchronization with head unit* This function is only available in vehicles...
Page 143
Controls in detail Control system Move the selection marker with button æ or ç to the Time/Date submenu. Press button j or k repeatedly until the message Time-Hours Press R To Confirm Time-Minute(s) Press R To Confirm appears in the multifunc- tion display.
Page 144
Lighting submenu Access the Lighting submenu via the Settings menu. Use the Lighting sub- menu to change the lamp and lighting settings on your vehicle. The following functions are available: Function Page Setting daytime running lamp mode (USA only) Setting locator lighting Setting night security illumination Setting interior lighting delayed...
Page 145
Controls in detail Control system Setting locator lighting With the locator lighting feature activated and the exterior lamp switch in position U, the following lamps will switch on during darkness when the vehi- cle is unlocked with the SmartKey: Parking lamps Tail lamps License plate lamps Side marker lamps...
Page 146
If after turning off the engine you do not open a door or do not close an opened door, the lamps will automatically switch off after 60 seconds. Move the selection marker with button æ or ç to the Lighting submenu.
Page 147
Controls in detail Control system Vehicle submenu Access the Vehicle submenu via the Settings menu. Use the Vehicle submenu to make general vehicle settings. The following functions are available: Function Page Selecting audio search function 146 Setting automatic locking For additional information on central locking, see “Automatic central locking”...
Page 148
Convenience* submenu Access the Convenience submenu via the Settings menu. Use the Convenience sub- menu to change the settings for a number of convenience features. The following function is available: Function Page Activating easy-entry/exit feature* Activating easy-entry/exit feature* Use this function to activate and deactivate the easy-entry/exit feature ( page 44).
Controls in detail Control system Trip computer menu Use the trip computer menu to call up statistical data on your vehicle. The following information is available: Function Page Fuel consumption statistics since start Fuel consumption statistics since last reset Resetting fuel consumption statistics Calling up range (distance to empty)
Resetting fuel consumption statistics Press and hold reset button J until the values of the statistics are reset The fuel consumption statistics reset auto- matically to 0 when either of the following values is exceeded: distance covered: 100000 miles (100000 km) time elapsed: 10000 hours Calling up range (distance to empty) Press button è...
Page 151
Controls in detail Control system Never operate radio transmitters equipped with a built-in or attached antenna (i.e. with- out being connected to an external antenna) from inside the vehicle while the engine is running. Doing so could lead to a malfunc- tion of the vehicle’s electronic system, pos- sibly resulting in an accident and/or personal injury.
Page 152
Ending a call or rejecting an incoming call Press button t. Dialing a number from the phone book If your telephone is ready to receive calls, you may select and dial a number from the phone book at any time. Press button è...
Page 153
Controls in detail Control system Redialing The control system stores the most recent- ly dialed phone numbers. This eliminates the need to search through your entire phone book. Press button è or ÿ repeatedly until the menu and the standby message appear in the multifunction display.
Manual transmission Manual transmission is standard equip- ment on select models and not available on all models. For information on driving with a manual transmission, see “Driving off” ( page 53). Warning! For vehicles equipped with a manual trans- mission, getting out of your vehicle with the gearshift lever not engaged in first or reverse gear and the parking brake not engaged is dangerous.
Warranty. Never hold the vehicle stopped on a hill by using the clutch pedal. The clutch may be damaged which is not covered by the Mercedes-Benz Limited Warranty. Do not exceed the engine speed limits. Refer to tachometer ( page 119) for engine speeds.
Automatic transmission* For more information on driving with an automatic transmission, see “Driving off” ( page 53). Your vehicle’s transmission adapts its gear shifting process to your individual driving style by continually adjusting the shift points up or down. These shift point adjust- ments are performed based on current operating and driving conditions.
This may cause serious damage to the drivetrain which is not covered by the Mercedes-Benz Limited Warranty. When the gear selector lever is in drive position D, you can influence transmission shifting by:...
Gear selector lever positions The current gear selector lever position appears in the multifunction display. 1 Current gear selector lever position Effect ì Park position Gear selector lever position when the vehicle is parked. Place gear selector lever in park position P only when vehicle is stopped.
Page 159
Coasting the vehicle, or driving for any other reason with gear selector lever in neutral position N can result in transmission damage that is not covered by the Mercedes-Benz Limited Warranty. Warning! Getting out of your vehicle with the gear selector lever not fully engaged in park position P is dangerous.
Driving tips Accelerator position Your driving style influences the transmission’s shifting behavior: Less throttle Earlier upshifting More throttle Later upshifting Kickdown Use kickdown when you want maximum acceleration. Press the accelerator past the point of resistance. Depending on the engine speed the transmission shifts into a lower gear.
Controls in detail Automatic transmission* Gear ranges With the gear selector lever in drive position D and driving in program mode C or S, you can select a gear range for the automatic transmission to operate within. Gear selector lever ( page 162): You can limit the gear range by pressing the gear selector lever to the left (D-), and reverse the gear range limit by pressing...
Automatic shift program The program mode selector switch is located on the lower part of the center console. Program mode selector switch C Comfort For comfort driving S Sport For standard driving Program mode selector switch on vehicles with AMG-Sport Package* and SLK 55 AMG only M Manual For manual gear shifting...
This may cause serious damage to the drivetrain which is not covered by the Mercedes-Benz Limited Warranty. The following instructions describe opera- tion of the gear selector lever when driving in the automatic program mode C or S.
Shift into reverse gear R or park position P only when the vehicle is stopped. Avoid spinning of a drive wheel for an extended period when driving off on slippery road surfaces. This may cause serious damage to the drivetrain which is not covered by the Mercedes-Benz Limited Warranty.
Page 165
Controls in detail Automatic transmission* Gearshift paddles (example illustration vehicles with AMG-Sport Package*) 1 Left shift paddle: limiting gear range or downshift (in program mode M) 2 Right shift paddle: extending gear range or upshift (in program mode M) You cannot shift with the steering wheel gearshift paddles when the gear selector lever is in position P, N or R.
Avoid spinning of a drive wheel for an extended period when driving off on slippery road surfaces. This may cause serious damage to the drivetrain which is not covered by the Mercedes-Benz Limited Warranty. Controls in detail Automatic transmission* The program mode selector switch is located on the lower part of the center console.
Page 167
( page 26). Otherwise the engine could be damaged which is not covered by the Mercedes-Benz Limited Warranty. Briefly press the gear selector lever to the right in the D+ direction.
Turn off the engine. Wait at least 10 seconds before restarting. Restart the engine. Move the gear selector lever to position D (for second gear) or position R. Have the transmission checked at an authorized Mercedes-Benz Center as soon as possible.
Controls in detail Good visibility For information on the windshield wipers, see “Windshield wipers” ( page 56). Headlamp cleaning system* The headlamps will automatically be cleaned with a high-pressure water jet when you have switched on the headlamps operated the windshield wipers with windshield washer fluid five times When you switch off headlamps, the counter resets.
Warning! The auto-dimming function does not react if incoming light is not aimed directly at sen- sors in the interior rear view mirror. The interior rear view mirror and the exterior rear view mirror on the driver’s side do not react, for example, if the wind screen* is installed.
Controls in detail Good visibility Warning! Do not use the vanity mirror while driving. Keep the mirrors in the sun visors closed while vehicle is in motion. Reflected glare can endanger you and others. Swing sun visors down when you experience glare.
Page 172
Switching off Press the rear window defroster switch F again in the control panel of the climate control or the automatic climate control*. The indicator lamp on the rear window defroster switch F goes out. If the rear window defroster switches off too soon and the indicator lamp starts flashing, this means that too many electrical consumers are operating simultaneously and there is insuffi-...
Page 174
Item 1 Right center air vent, adjustable 2 Thumbwheel for air volume control for fixed/adjustable right center air vents 3 Right center air vent, fixed 4 Right side defroster air vent, fixed 5 Right side air vent, adjustable 6 Thumbwheel for air volume control for adjustable right side air vent 7 Climate control panel Item...
Have a clogged filter replaced as soon as possible at an authorized Mercedes-Benz Center. The air conditioning will not engage (no cooling) if the A/C mode is deactivated ( page 174).
Warning! Follow the recommended settings for heating and cooling given on the following pages. Otherwise the windows could fog up, impairing visibility and endangering you and others. If the vehicle interior is hot, ventilate the in- terior before driving off. The climate control will then adjust the interior temperature to the set value much faster.
Controls in detail Climate control Decreasing Turn temperature control 1 and/or 4 ( page 174) slightly counterclockwise. The climate control system will corre- spondingly adjust the interior air tem- perature. Adjusting air distribution Use air distribution control 3 ( page 174) to adjust the air distribution. The following symbols are found on the control: Symbol...
Adjusting air volume Ten blower speeds are available. Use air volume control 2 ( page 174) to adjust the air volume. Basic settings Heating (winter) Turn temperature controls 1 and 4 ( page 174) to the desired position. Turn air volume control 2 ( page 174) to level 2 or higher.
Controls in detail Climate control Deactivating Press button P ( page 174) again. The indicator lamp on the button goes out. The previous settings are once again in effect. The cooling remains switched on. Windshield fogged on the outside Switch the windshield wipers on ( page 56).
Page 180
Air recirculation mode with convenience closing or opening feature Warning! Never operate the side windows if there is the possibility of anyone being harmed by the closing procedure. When using the air recirculation mode with convenience closing feature, should the up- ward movement of a window be blocked by some obstruction including but not limited to arms, hands, fingers, etc., the automatic...
Controls in detail Climate control Air conditioning The cooling function, only operational when the engine is running, cools the vehicle interior down to the selected temperature. The cooling function also dehumidifies the air in the vehicle interior, thus preventing the windows from fogging up.
Set air volume control 2 ( page 177) to position 5. The ventilation operates with maximum blower speed. Turn temperature controls 1 and 4 ( page 174) completely counterclock- wise to their end stops. The lowest temperature for both sides is set.
Page 184
Item 1 Cockpit air vent (depending on vehicle production date) 2 Thumbwheel for air volume control for cockpit air vent (depending on vehicle production date) 3 Right center air vent, adjustable 4 Thumbwheel for air volume control for fixed/adjustable right center air vents 5 Right center air vent, fixed 6 Right side defroster air vent, fixed...
Page 185
Controls in detail Automatic climate control* Item 1 Air volume control, manual 2 Air distribution and air volume (automatic mode) 3 Front defroster 4 Temperature control, left, raising 5 Automatic climate control on/off (complete system) 6 Temperature control, right, raising 7 Rear window defroster 8 Air distribution control, manual 9 Residual heat/ventilation...
Have a clogged filter replaced as soon as possible at an authorized Mercedes-Benz Center. The air conditioning will not engage (no cooling) if the A/C mode is deactivated ( page 184).
Controls in detail Automatic climate control* Reactivating Switch on the ignition ( page 37). Press button ´ ( page 184) again. The previous settings are once again in effect. Press button U ( page 184). The indicator lamp on the button comes on.
Increasing Press temperature button(s) 4 and/or 6 ( page 184) until the desired temperature appears in the control panel display e ( page 184). The automatic climate control system will correspondingly adjust the interior air temperature. Decreasing Press temperature button(s) b and/or c ( page 184) until the desired temperature appears in the control panel display e ( page 184).
Controls in detail Automatic climate control* Opening the cockpit air vent and center air vents Center air vents Turn thumbwheels 4 and b ( page 182) to the first stop. Center air vents 3, 5, a and c are open. Turn thumbwheels 4 and b ( page 182) upward all the way.
Front defroster You can use this setting to defrost the windshield, for example if it is iced up. You can also defog the windshield and the side windows. Keep this setting selected only until the windshield or the side windows are clear again. Activating Press button P ( page 184).
Controls in detail Automatic climate control* Air recirculation mode Switch to air recirculation mode to prevent unpleasant odors from entering the vehicle from the outside (e.g. before driving through a tunnel). This setting cuts off the intake of outside air and recirculates the air in the interior.
Convenience closing Press and hold button , until the windows are closed or have reached the desired position. The indicator lamp on the button comes on. The air recirculation mode is activated. The closing of the windows can be immedi- ately halted by releasing button ,.
Controls in detail Automatic climate control* Deactivating It is possible to deactivate the air condi- tioning (cooling) function of the automatic climate control system. The air in the vehicle will then no longer be cooled or dehumidified. Press button œ ( page 184). The indicator lamp on the button goes out.
Audio system Audio and telephone*, operation These instructions are intended to help you become familiar with your Mercedes-Benz audio system. They con- tain useful tips and a detailed description of the user functions. Warning! In order to avoid distraction which could...
The volume will increase or decrease depending on the direction turned. If your vehicle equipment includes a Mercedes-Benz specified mobile telephone*, you can adjust its volume separately from the volume of the audio system while the telephone is being used.
Page 198
Adjusting sound functions The bass and treble functions are called up by pressing the O button. Settings for bass and treble are stored separately for the AM and FM wavebands, weather band, CD mode and telephone mode. Bass Press O button repeatedly until BASS appears in the display.
Page 199
Controls in detail Audio system Returning sound functions to factory settings Press O button to call up settings menu in the display. Press soft key briefly; the respec- tive sound function is reset to its center level. Press and hold soft key until RESET appears in the display.
Telephone* muting If your vehicle equipment includes a Mercedes-Benz specified mobile telephone*, you can adjust its volume separately from the volume of the audio system while the telephone* is being used. Radio operation Selecting radio mode Press b button. Calling up wavebands You can choose from among the FM, AM and WB wavebands.
Page 201
Controls in detail Audio system Calling up wavebands for radios with SAT Press soft key repeatedly until desired waveband has been selected. The FM, AM and WB wavebands are called up one after another. The waveband currently selected appears in the upper left-hand corner of the display.
Page 202
Manual tuning Select desired waveband. Press G or H button for approximately 3 seconds. Press button repeatedly until the desired frequency has been reached. Step-by-step station tuning takes place in ascending or descending order. Each time the button is pressed, the radio tunes further by 0.2 MHz.
Page 203
Controls in detail Audio system Autostore – automatic station memory The Autostore memory function provides an additional memory level. The station memory for manually stored stations is not overwritten. Calling up Autostore memory level and storing stations Press soft key briefly. The radio switches to the Autostore memory level.
Search Press G or H button to tune in the next receivable weather band station. If no weather band station is received after three consecutive scans of the complete frequency range, then the scan stops at the channel with which it began and NO WB FOUND appears in the display.
Page 205
Contact an authorized Mercedes-Benz Center for details and availability for your vehicle. Note that categories and channels shown in illustrations are dependent on programming content delivered by the service provider.
Page 206
Press soft key. The twelve-digit electronic serial number (ESN) of the SAT tuner* installed in your vehicle is displayed. This information is required to call the SIRIUS Service Center for an activation request. Credit card information may also be required for your application. The activation process takes approximately 5 to 10 minutes after calling the SIRIUS Service Center.
Page 207
Controls in detail Audio system Accessing via number keys Enter number of preset you wish to select, e.g. 1. The radio plays the station stored under this number and the PTY function changes to the category corresponding to the station. Tuning via manual channel input Example: tuning in channel 16 Press *.
Page 208
The system will automatically switch to a station of the selected category if the currently selected station is not of the selected category. Otherwise, the currently selected station remains tuned. Tuning a station within the selected category The channels identified for the currently selected category are arranged numerically.
Controls in detail Audio system Storing stations Tune in desired station. Press and hold desired station button 1 to R until a brief signal tone is heard. The frequency is stored on the selected station button. The radio saves the current station at the memory preset selected.
Page 210
CD drive or CD changer. In certain situations, the CDs can then no longer be ejected and cause damage to the drive. Such damage is not covered by the Mercedes-Benz Limited Warranty. Your CD drive or CD changer has been designed to play CDs which correspond to the EN 60908 standard.
Page 211
Controls in detail Audio system Tips on handling CDs Handle CDs carefully to prevent interference during playback. Avoid scratches, fingerprints and dust on the CDs. Do not write on CDs or apply any labels or other material to them. Clean CDs from time to time with a commercially available cleaning cloth.
Page 212
Compatible bit and sampling rates Fixed and variable bit rates of up to 320 kBit/s are possible. The following table lists possible sampling rates: MPEG1 44.1 KHz, 48 KHz, Audio Layer3 32 KHZ MPEG2 22.5 KHz, 24 KHz, Audio Layer3 16 KHz MPEG2.5 11.025 KHz,...
Page 213
CD in the slot with another CD still loaded will cause damage to the CD drive not covered by the Mercedes-Benz Limited Warranty. If a CD has been inserted incorrectly or cannot be read, WRONG CD0 will appear in the display.
Page 214
A light-emitting diode in the buttons shows the status of the corresponding magazine slot. CD loading slot 1 is above buttons 2 and is used to load CDs. LEDs no LED is lit Magazine slot is empty. green LED flashes CD can be loaded. red LED is lit Magazine slot is in use.
Page 215
Controls in detail Audio system Loading several CDs Open the glove box. Press button 2 of an empty magazine slot for more than 2 seconds. The light-emitting diodes in all the mag- azine slot buttons light up several times in green, and ALL LOAD appears in the display.
Page 216
If you do not take the CD from the CD load- ing slot within 15 seconds, the CD changer will automatically pull the CD back in. The system will then play the CD. If you are listening to a CD while ejecting another CD from the changer: The Audio system stops playing the CD while another CD is being eject- ed.
Page 217
Controls in detail Audio system Playing CDs Single CD player in the audio unit Press i button. will appear in the upper left-hand corner of the display. The CD will resume playback at the point where it was switched off. CD changer* Press Q button.
Page 218
Direct track entry You can make a direct selection from among the tracks on a CD. Press * button. Enter track number using buttons 1 to R. The number of the track being played appears next to TRACK in the display. You can only enter available track numbers.
Page 219
Controls in detail Audio system Random play The random function (RDM) plays the tracks of the current CD in random order. When you start the RDM function, the RPT function is automatically switched off. Switching on random Press soft key. appears in the display.
The standard CD playback menu appears in the display. GSM network phones Using your Mercedes-Benz specified mobile telephone*, a number of functions and operating steps can be performed and displayed in the audio system display. Controls in detail...
Page 221
If your audio system is set up for telephone operation, the t symbol will appear in the display. When you insert your Mercedes-Benz specified mobile telephone* into the telephone cradle, you will be prompted to enter your PIN for 30 seconds ( page 220).
Page 222
Adjusting the volume Turn rotary control of button during a telephone call. The volume will increase or decrease depending on the direction turned. The volume can be adjusted separately for telephone mode and audio mode. Adjusting sound Adjust sound during a telephone call. Sound adjustment see “Adjusting sound functions”...
Page 223
Controls in detail Audio system Searching and calling up telephone book entries by name You can access your mobile telephone’s phone book using the audio system. You can access both the main entries and the sub-entries of your phone book. Press soft key or press button ‚...
Page 224
Returning calls received Press soft key or press button ‚ or ƒ. Press soft key (received calls). The number of received calls and then the call last received appear briefly in the display. Select desired telephone number with button ‚ or ƒ. The letter and the number of the memory position appear in the...
Page 225
Controls in detail Audio system Redial If the number you have dialed is busy, you can again place calls to the last ten telephone numbers dialed using the redial function. If you have activated the automatic redial function on your telephone, the number of the person being called is automatically redialed after a short waiting period if there is a busy signal.
Page 226
Muting a call It is possible to mute a call; the caller is then no longer able to hear you. Mute on Press soft key. MIC MUTE will appear in the display. Mute off Press soft key again. Terminating a call Press t button.
If your audio system is set up for telephone operation, the t symbol will appear in the display. When you insert your Mercedes-Benz specified mobile telephone* into the telephone cradle, you will be prompted to enter your PIN for 30 seconds ( page 227).
Page 228
Switching on the telephone Switching on the telephone Press h button. If you have programmed an unlock code for the telephone, you must now enter the code. Enter code using buttons 1 to R. If necessary, correct number entered with the soft key.
Page 229
Controls in detail Audio system If necessary, correct number entered with the soft key. Press soft key briefly to delete the last digit entered; press soft key and hold to delete the complete number. After correct telephone number has been entered, press s button. If the telephone number has been saved together with a name in the phone book, the name will appear in the display.
Page 230
Press and hold button ‚ or ƒ until desired initial letter has been reached. Press button ‚ or ƒ repeatedly until desired entry has been reached. The stored entries are selected in alphabetical order with the sub-entries. Several sub-entries can be stored for each main entry (name).
Page 231
Controls in detail Audio system Speed dial If you have stored telephone numbers as speed dial numbers in your telephone, you can also enter these with buttons 1 to R on the radio unit. Press desired button 1 to R briefly.
Page 232
Accepting an incoming call If the telephone is active in the background (reception symbol is visible in the display), the audio source is muted when an incom- ing call is received. A ringing tone can be heard and the caller’s telephone number, or the name under which the telephone number has been saved in the telephone book, appears in the display.
Page 233
Controls in detail Audio system Switching between calls Press s button. This switches between the calls. The non-active call is kept on hold. Terminating a call Press t button. The current call is terminated. The connection to the caller previously kept on hold is also interrupted;...
Emergency calls “911” The following describes how to dial a “911” emergency call using the audio system head unit when a Mercedes-Benz specified mobile phone* is inserted in the phone cradle. Unless otherwise specified, the descriptions refer to the audio system head unit.
Page 235
Controls in detail Audio system Placing a “911” emergency call using audio head unit with the phone unlocked Press h button to switch to telephone operation. Enter 911 using the number keypad on the audio head unit. Press s button for dialing to begin. DIALING appears in the audio display while the telephone establishes the...
Power windows Opening and closing the windows The windows are opened and closed elec- trically. The switches for both door win- dows are located on the driver’s door. The switch for operating the passenger-side door window is located on the passenger door.
Page 237
Controls in detail Power windows You can also open or close the windows using the SmartKey* ( page 238) or the retractable hardtop switch ( page 237). You can close and open the windows using the air recirculation switch , in the control panel of the climate control ( page 178) or the automatic climate control* ( page 190).
Page 238
If the upward movement of the window is blocked during the closing procedure, the win- dow will stop and open slightly. Remove the obstruction, press the respective switch at the symbol j again past the resis- tance point and release. If the window still does not close when there is no obstruction, press and hold the respective switch at the symbol j.
Page 239
Controls in detail Power windows Opening Push the retractable hardtop switch in quick succession twice in direction of arrow 1. All side windows open. You can operate the rear side windows only by using the retractable hardtop switch. Closing Push the retractable hardtop switch in quick succession twice in direction of arrow 2.
Warning! When closing the side windows and retract- able hardtop, make sure that there is no danger of anyone being harmed by the closing procedure. If potential danger exists, proceed as fol- lows: Release button ‹ to stop the closing procedure.
Make sure to close the retractable hardtop when leaving the vehicle. If water enters the vehicle interior, vehicle electronics could be damaged which is not covered by the Mercedes-Benz Limited Warranty. When opening and closing the retractable hardtop, make sure...
Page 242
Luggage cover The luggage cover is located in the trunk. Luggage cover Closing Pull the luggage cover at the handle in direction of the arrow until it engages on both sides at the trunk sill. Opening Press the release handle on the lug- gage cover.
Page 243
Controls in detail Retractable hardtop The switch for opening/closing the retract- able hardtop is on the lower part of the center console. Retractable hardtop switch 1 Opening 2 Closing For operating the power windows with the retractable hardtop switch ( page 237). Opening Push and hold the retractable hardtop switch in direction of arrow 1 until the...
Page 244
Warning! If the retractable hardtop does not com- pletely open or close, the roof hydraulics will lose pressure and the retractable hardtop is lowered after approximately 7 minutes when the ignition is switched on. after approximately 15 seconds when the ignition is switched off. Shortly before the hardtop is lowered, a warning will sound.
Page 245
Controls in detail Retractable hardtop Unlocked status noticed while driving Warning! Stop the vehicle and lock the retractable hardtop before continuing to drive. You could otherwise endanger yourself and oth- ers. Stop the vehicle and leave the ignition switched on. To lock the retractable hardtop in its fully closed position, push the retract- able hardtop switch forward until the...
Page 246
Opening (Summer opening feature) Press and hold unlock button Œ un- til the retractable hardtop is complete- ly open. The retractable hardtop and windows begin to open after approximately 1 second. In the multifunction display you will see the message Retractable Roof In Operation Release button Œ...
If the retractable hardtop still does not open, close, or lock properly, have the retractable hardtop system checked at an authorized Mercedes-Benz Center. There is a malfunction in the retract- able hardtop system. Contact an authorized Mercedes-Benz Center. Wind screen* Warning! The wind screen can restrict the driver’s...
Page 248
6 Handle cap Installing Remove wind screen 1 from its stor- age bag and unfold. The storage bag is located on the wall behind the seat backrests. Attach supporting straps 3 to fasten- ing pins 4. Make sure the lower wind screen edging is inserted through the gap 5 between the stor- age compartment and the rear panel.
Controls in detail Driving systems The driving system of your vehicle is described on the following pages: Cruise control, with which the vehicle can maintain a preset speed. ® The BAS, ABS and ESP driving systems are described in the “Safety and Security” section ( page 84).
Page 250
1 Set current or higher speed 2 Set current or lower speed 3 Cancel cruise control 4 Resume to last set speed Warning! Cruise control brakes automatically so that the set speed is not exceeded. The brake pedal is depressed automatically to do this. Keep in mind that cruise control is a conve- nience system designed to assist the driver during vehicle operation.
Page 251
Controls in detail Driving systems On uphill or downhill grades, the cruise control may not be able to maintain the set speed. Once the grade eases, the set speed will be resumed. On downhill grades, the cruise control maintains the set speed with braking from the vehicle’s braking system.
Page 252
Setting a higher speed Lift the cruise control lever in direction of arrow 1 ( page 249) and hold it up until the desired speed is reached. Release the cruise control lever. The new speed is set. Setting a lower speed Depress the cruise control lever in direction of arrow 2 ( page 249) and hold it down until the desired speed is...
This vehicle is not designed to carry items on its roof. Roof rails and any roof-mounted devices, unless expressly approved by Mercedes-Benz for use on this vehicle model, must not be used as they will damage the vehicle and retractable hardtop.
Useful features Storage compartments Warning! To help avoid personal injury during a colli- sion or sudden maneuver, exercise care when storing objects in the vehicle. Put lug- gage or cargo in the trunk if possible. Do not place anything on shelf behind the roll bars. Parcel nets cannot secure hard or heavy ob- jects.
Controls in detail Useful features Storage compartment between the seat backrests 1 Storage compartment lid release 2 Storage compartment Press storage compartment lid release 1 to open. The storage compartment lid opens downward. Push storage compartment lid up until it engages to close it. Parcel net in passenger footwell A small convenience parcel net is located in the passenger footwell and behind the...
Liquids spilled on vehicle equipment may cause damage not covered by the Mercedes-Benz Limited Warranty. When not in use, keep the cup holder closed. An open cup holder may cause injury to you or others when contacted during braking, vehicle maneuvers, or in an acci- dent.
Controls in detail Useful features Removing ashtray insert Warning! Remove front ashtray only with vehicle standing still. Set the parking brake to se- cure vehicle from movement. Move gear selector lever to position N (manual trans- mission: into second gear). With gear selec- tor lever in position N (manual transmission: into second gear), turn off the engine.
1 Cigarette lighter Push in cigarette lighter 1. Cigarette lighter 1 will pop out auto- matically when hot. Reinsert cigarette lighter 1 in its socket after use. The lighter socket can be used to accommodate 12V DC electrical accessories (up to a maximum of 85 W) designed for use with the standard “cigarette lighter”...
Controls in detail Useful features Floormat (driver’s side only) Warning! Whenever you are using floormats, make sure there is enough clearance and the floormats are securely fastened. Floormats should always be securely fas- tened using eyelets 4 and retainer pins 5. Before driving off, check that the floormats are securely in place and adjust them if necessary.
The external antenna must be approved by Mercedes-Benz. Please contact an autho- rized Mercedes-Benz Center for informa- tion on the installation of an approved external antenna. Refer to the radio trans- mitter operation instructions regarding use of an external antenna.
Page 261
Please note that these functions are only available with Mercedes-Benz approved mobile phones. Please contact an autho- rized Mercedes-Benz Center for informa- tion on features available for your mobile phone of choice. The cradle is located in the front center armrest storage/telephone* compartment ( page 253).
Page 262
The mobile phone is linked to the hands-free device and the multifunc- tion steering wheel. The battery is charged depending on its charge status and the position of the SmartKey in the starter switch. The charge procedure will be indicated in the mobile phone’s display.
Controls in detail Useful features Installing a different mobile phone cradle Example illustration 1 Contact plate 2 Recesses 3 Mobile phone cradle Insert mobile phone cradle 3 into recesses 2 of contact plate 1. Push mobile phone cradle 3 forward until it engages.
Page 264
To activate, press the SOS button, the Roadside Assistance button • or the Information button ¡, depend- ing on the type of response required. The SOS button is located in the overhead control panel. The Roadside Assistance button • ( page 266) and the Information button ¡ ( page 267) are located in the center armrest storage/telephone* compartment.
Page 265
If a malfunction is indicated as outlined above, the system may not operate as ex- pected. Have the system checked at the nearest Mercedes-Benz Center as soon as possible. Emergency calls An emergency call is initiated automatical- ly following an accident in which the emer- gency tensioning devices (ETDs) or air bags deploy.
Page 266
Warning! If the indicator lamp in the SOS button is flashing continuously and there was no voice connection to the Response Center established, then the Tele Aid system could not initiate an emergency call (e.g. the rele- vant cellular phone network is not available). The message Call Failed appears in the multifunction display for approximately 10 seconds.
Page 267
Open the storage/telephone* com- partment ( page 253). Press and hold button 1 (for longer than 2 seconds). A call to a Mercedes-Benz Roadside Assistance dispatcher will be initiated. The button will flash while the call is in progress. The message...
A voice connection between the Customer Assistance Center representative and the occupants of the vehicle will be estab- lished. Information regarding the operation of your vehicle, the nearest Mercedes-Benz Center or Mercedes-Benz USA products and services is available to you.
Page 269
(in red) at any time, the Tele Aid system has detected a malfunction or the service is not currently active, and may not initiate a call. Visit your Mercedes-Benz Center and have the system checked or contact the Response Center at 1-800-756-9018 (in the USA) or 1-888-923-8367 (in Canada) as soon as possible.
Page 270
In case you have locked your vehicle unin- tentionally (e.g. SmartKey inside vehicle), and the reserve SmartKey is not handy: Contact the Mercedes-Benz Response Center at 1-800-756-9018 (in the USA) or 1-888-923-8367 (in Canada). You will be asked to provide your pass- word which you provided when you completed the subscriber agreement.
Controls in detail Useful features Garage door opener* The integrated remote control is capable of operating up to three separately controlled devices. It provides a convenient way to re- place up to three hand-held remote con- trols used to operate devices such as garage door openers, gate openers, or oth- ®...
Page 272
When programming a garage door opener, it is advised to park outside the garage. Do not run the engine while programming the integrated remote control. Inhalation of exhaust gas is hazardous to your health. All exhaust gas contains carbon monoxide (CO), and inhaling it can cause unconscious- ness and possible death.
Page 273
Controls in detail Useful features Step 5: After indicator lamp 1 changes from a slow to a rapidly flashing light, release the hand-held remote control button and the signal transmitter button. Step 6: Press and hold the just-trained signal transmitter button (2, 3 or 4) and observe indicator lamp 1.
Page 274
Step 11: Press, hold for 2 seconds and release same signal transmitter button a second time to complete the training process. Some garage door openers (or other rolling code equipped devices) may require you to press, hold for 2 seconds and release the same signal transmitter button a third time to complete the training process.
Page 275
Controls in detail Useful features Reprogramming a single signal trans- mitter button To program a device using a signal trans- mitter button previously trained, follow these steps: Switch on the ignition ( page 37). Press and hold the desired signal transmitter button (2, 3 or 4).
Page 276
Certain types of garage door openers are incompatible with the integrated remote control. If you should experience further difficulties with programming the integrated remote control, contact an authorized Mercedes-Benz Center, or call Mercedes-Benz Customer Assistance Center (in the USA only) at 1-800-FOR-MERCedes, or Customer Service (in Canada) at 1-800-387-0100.
Controls in detail Useful features Heated steering wheel* (SLK 280, SLK 350, Canada only) The steering wheel heating warms up the leather area of the steering wheel. The stalk is located on the lower left-hand side of the steering wheel. 1 Switching on 2 Indicator lamp 3 Switching off...
Operation The first 1000 miles (1500 km) Driving instructions At the gas station Engine compartment Tires and wheels Winter driving Maintenance Vehicle care...
Operation The first 1000 miles (1500 km) In the “Operation” section you will find de- tailed information on operating, maintain- ing and caring for your vehicle. The more cautiously you treat your vehicle during the break-in period, the more satisfied you will be with its performance later on.
Maintenance Booklet and as required by the Maintenance System. Contact an authorized Mercedes-Benz Center. Fuel consumption is also increased by driv- ing in cold weather, in stop-and-go traffic, on short trips and in hilly area.
Operation Driving instructions Power assistance Warning! With the engine not running, there is no power assistance for the brake and steering systems. In this case, it is important to keep in mind that a considerably higher degree of effort is necessary to brake and steer the vehicle.
Page 282
Contact an authorized Mercedes-Benz Center. Install only brake pads and brake fluid recommended by Mercedes-Benz. Warning! If other than recommended brake pads are installed, or other than recommended brake fluid is used, the braking properties of the vehicle can be degraded to an extent that safe braking is substantially impaired.
® period with the ESP switched off. Doing so may cause serious damage to the drivetrain which is not covered by the Mercedes-Benz Limited Warranty. Simultaneously depressing the accelerator pedal and applying the brake reduces engine performance and causes premature brake and drivetrain wear.
Inspect the tires and the vehicle undercar- riage for possible damage. If the vehicle or tires appear unsafe, have the vehicle towed to the nearest Mercedes-Benz Center or tire dealer for repairs. Treadwear indicators (TWI) are required by law. These indicators are located in six...
Exercise appro- priate caution. Avoid spinning of a drive wheel. This may cause serious damage to the drivetrain which is not covered by the Mercedes-Benz Limited Warranty.
( page 322). If you are uncertain about the correct reading of the information given on a tire’s sidewall, any authorized Mercedes-Benz Center will be glad to assist you. For information on speed rating for winter tires, see “Winter tires” ( page 335).
Operation Driving instructions Winter driving instructions The most important rule for slippery or icy roads is to drive sensibly and to avoid abrupt acceleration, braking and steering maneuvers. Do not use the cruise control system under such conditions. When the vehicle is in danger of skidding, move gear selector lever* to position N or declutch in case of manual transmission.
The trunk is the preferred place to carry objects. Driving abroad Abroad, there is an extensive Mercedes-Benz service network at your disposal. If you plan to drive into areas which are not listed in the index of your Mercedes-Benz Center directory, you should request pertinent information from an authorized Mercedes-Benz Center.
Refer to the radio transmitter operation instructions regarding use of an external antenna. Catalytic converter Your Mercedes-Benz is equipped with monolithic-type catalytic converters, an important element in conjunction with the oxygen sensors to achieve substantial control of the pollutants in the exhaust emissions.
Engine adjustments should not be altered in any way. Moreover, the specified service jobs must be carried out regularly accord- ing to Mercedes-Benz servicing require- ments. For details refer to the Maintenance Booklet. Warning! Inhalation of exhaust gas is hazardous to your health.
Page 291
The engine should not be operated with a coolant temperature above 248°F (120°C). Doing so may cause serious engine damage which is not covered by the Mercedes-Benz Limited Warranty. During severe operating conditions, e.g. stop-and-go city traffic, the coolant temperature...
In case that the central locking system does not release the fuel filler flap, or the opening mechanism is clamping, contact Roadside Assistance or an authorized Mercedes-Benz Center. 1 To open fuel filler flap 2 To insert fuel filler cap Remove the SmartKey from the starter switch.
Notify an authorized Mercedes-Benz Center immediately. Do not add brake fluid as this will not solve the problem.
Page 294
Coolant For normal replenishing, use water (potable water quality). For more information on coolant, see “Coolant level” ( page 300) and “Fuels, coolants, lubricants, etc.” ( page 451). Engine oil level For information on engine oil, see “Engine oil” ( page 296). Vehicle lighting Check function and cleanliness.
Operation Engine compartment Hood Warning! Do not pull the release lever while the vehi- cle is in motion. Otherwise the hood could be forced open by passing air flow. This could cause the hood to come loose and injure you and/or others. Opening Warning! If you see flames or smoke coming from the...
Page 296
Pull hood lock release lever 1 in direc- tion of arrow. The hood is unlocked. To avoid damage to the windshield wipers or hood, never open the hood if the wiper arms are folded forward away from the windshield. 2 Lever for opening the hood Push lever 2 on the hood upward to release hood.
Do not use any special lubricant additives, as these may damage the drive assemblies. Using special additives not approved by Mercedes-Benz may cause damage not covered by the Mercedes-Benz Limited Warranty. More information on this subject is available at any authorized Mercedes-Benz Center.
Page 298
One of the following messages will subsequently appear in the multifunc- tion display: Engine Oil Level (Canada: Add 1.0 qt. 1.0 liter to reach max. oil level Add 1.5 qts. (Canada: 1.5 liters to reach max. oil level Add 2.0 qts. (Canada: 2.0 liters to reach max.
Excess oil must be siphoned or drained off. It could cause damage to the engine and catalytic converter not covered by the Mercedes-Benz Limited Warranty. For more information on messages in the display concerning engine oil, see the “Practical hints” section ( page 360).
Page 300
Maintenance System, or changing of oil and oil filter at change intervals longer than those called for by the Maintenance System will result in engine or emission control system damage not covered by the Mercedes-Benz Limited Warranty. Operation Engine compartment...
Vehicles with automatic transmission*: The transmission fluid level does not need to be checked. If you notice transmission fluid loss or gear shifting malfunctions, have an authorized Mercedes-Benz Center check the transmission. Coolant level The engine coolant is a mixture of water and anticorrosion/antifreeze.
The coolant expansion tank is located on the passenger side of the engine compart- ment. SLK 350 (example illustration) 1 Coolant expansion tank 2 Cap 3 Marking bar in the expansion tank Using a rag, turn cap 2 slowly approx- imately one half turn counterclockwise to release any excess pressure.
When replacing the battery, always use batteries approved by Mercedes-Benz. If you do not intend to operate your vehicle for an extended period of time, consult an authorized Mercedes-Benz Center about...
Page 304
Warning! Observe all safety instructions and precau- tions when handling automotive batteries. Risk of explosion. Fire, open flames and smoking are prohibited when handling batteries. Avoid creating sparks. Battery acid is caustic. Do not allow it to come into contact with skin, eyes or clothing.
When replacing rims, only use genuine Mercedes-Benz wheel bolts specified for the particular rim type. Failure to do so can re- sult in the bolts loosening and may lead to an accident.
Tire care and maintenance Warning! Regularly check the tires for damage. Damaged tires can cause tire inflation pressure loss. As a result, you could lose control of your vehicle. Worn, old tires can cause accidents. If the tire tread is badly worn, or if the tires have sustained damage, replace them.
Page 307
Operation Tires and wheels Tread depth Do not allow your tires to wear down too far. Adhesion properties on wet roads are sharply reduced at tread depths of less than in (3 mm). Treadwear indicators (TWI) are required by law. These indicators are located in six places on the tread circumference and become visible at a tread depth of approx- imately...
Direction of rotation Unidirectional tires offer added advan- tages, such as better hydroplaning perfor- mance. To benefit, however, you must make sure the tires rotate in the direction specified. An arrow on the sidewall indicates the intended direction of rotation (spinning) of the tire.
Page 309
Operation Tires and wheels Tire and Loading Information Warning! Do not overload the tires by exceeding the specified load limit as indicated on the Tire and Loading Information placard on the driver’s door B-pillar. Overloading the tires can overheat them, possibly causing a blowout.
Page 310
1 Seating capacity information on the Tire and Loading Information placard Steps for determining correct load limit The following steps have been developed as required of all manufacturers under Title 49, Code of U.S. Federal Regulations, Part 575 pursuant to the “National Traffic and Motor Vehicle Safety Act of 1966”.
Page 311
Operation Tires and wheels Example Combined weight limit of occupants and cargo from Tire and Loading Information placard 1500 lbs 1500 lbs The higher the weight of all occupants, the less cargo and luggage load capacity is available. For more information, see “Trailer tongue load”...
The tongue load typically is 10 percent of the trailer weight and every- thing loaded in it. Your Mercedes-Benz has been designed primarily to carry passengers and their cargo. Mercedes-Benz does not recom- mend trailer towing with your vehicle.
Page 313
Operation Tires and wheels Do not overload the tires by exceeding the specified load limit as indicated on the Tire and Loading Information placard on the driver’s door B-pillar. Overloading the tires can overheat them, possibly causing a blowout. Overloading the tires can also result in handling or steering problems, or brake failure.
If your vehicle is not equipped with the tire inflation pressure label on the inside of the fuel filler flap, contact an authorized Mercedes-Benz Center for proper tire inflation pressure. Driving comfort may be reduced when the tire inflation pressure is adjusted to the value for...
Page 315
Operation Tires and wheels Warning! Follow recommend tire inflation pressures. Do not underinflate tires. Underinflated tires wear excessively and/or unevenly, adversely affect handling and fuel economy, and are more likely to fail from being over- heated. Do not overinflate tires. Overinflated tires can adversely affect handling and ride comfort, wear unevenly, increase stopping distance, and result in sudden deflation...
Page 316
Run Flat Indicator* (Canada only) While the vehicle is being driven, the Run Flat Indicator monitors the set tire inflation pressures by evaluating each wheel’s rota- tional speed. This allows the system to de- tect a significant loss of pressure in a tire. If a wheel’s rotational speed changes due to falling tire inflation pressure, you will see a corresponding warning message in...
Page 317
Operation Tires and wheels Restarting the Run Flat Indicator The tire inflation pressure monitor must be restarted in the following situations: If you have changed the tire inflation pressure If you have replaced the wheels or tires If you have installed new wheels or tires Using the Tire and Loading Information placard on the driver’s door B-pillar or,...
Page 318
Checking tire pressure electronically with the Tire Pressure Monitoring System (TPMS), (USA only) The Tire Pressure Monitoring System (TPMS) is equipped with a combination low tire pressure/TPMS malfunction telltale in the instrument cluster ( page 26). Depending on how the telltale illuminates, it indicates a low tire pressure condition or a malfunction in the TPMS system itself: If the telltale illuminates continuously, one...
Page 319
Operation Tires and wheels Warning! Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recom- mended by the vehicle manufacturer on the Tire and Loading Information placard or, if available, on the tire inflation pressure label. If your vehicle has tires of a different size than the size indicated on the Tire and Loading Information placard or, if available,...
Page 320
Tire inflation pressure warnings If the system detects a significant loss of tire inflation pressure in one or more than one tire, a message appears in the multi- function display. Example illustration In addition, a warning signal sounds. Restarting the TPMS Warning! It is the driver’s responsibility to calibrate the TPMS on the recommended cold infla-...
Page 321
Operation Tires and wheels Press reset button J ( page 118). The following message will appear in the multifunction display: Restart tire pressure monitor? Press button æ. The following message will appear in the multifunction display: Tire Pressure Monitor Restarted After driving a few minutes the current tire inflation pressure values are accepted as reference pressures and...
MOExtended system* The MOExtended system allows you to continue driving your vehicle even if there is a total loss of pressure in one or more tires. You may only use the MOExtended system in conjunction with the Run Flat Indicator* (Canada vehicles) ( page 315) or TPMS (U.
Page 323
Operation Tires and wheels Tire size designation, load and speed rating 1 Tire width 2 Aspect ratio in % 3 Radial tire code 4 Rim diameter 5 Tire load rating 6 Tire speed rating For illustration purposes only. Actual data on tires are specific to each vehicle and may vary from data shown in above illustration.
Page 324
Rim diameter The rim diameter 4 ( page 322) is the diameter of the bead seat, not the diameter of the rim edge. Rim diameter is indicated in inches (in). Tire load rating The tire load rating 5 ( page 322) is a numerical code associated with the maximum load a tire can support.
Page 325
Operation Tires and wheels Tire load rating 5 ( page 322) and Tire speed rating 6 ( page 322) are also referred to as “service description”. Summer tires Index Speed rating up to 100 mph (160 km/h) up to 106 mph (170 km/h) up to 112 mph (180 km/h) up to 118 mph (190 km/h) up to 130 mph (210 km/h)
All-season and winter tires Index Speed rating Q M+S up to 100 mph (160 km/h) T M+S up to 118 mph (190 km/h) H M+S up to 130 mph (210 km/h) V M+S up to 149 mph (240 km/h) or M+S.for winter tires. Not all M+S rated tires provide special winter performance.
Operation Tires and wheels DOT, Tire Identification Number (TIN) U.S. tire regulations require each new tire manufacturer or tire retreader to mold a TIN into or onto a sidewall of each tire produced. The TIN is a unique identifier which facili- tates efforts by tire manufactures to notify purchasers in recall situations or other safety matters concerning tires and gives...
Tire type code The code 4 ( page 326) may, at the option of the manufacturer, be used as a descriptive code for identifying significant characteristics of the tire. Date of manufacture The date of manufacture 5 ( page 326) identifies the week and year of manufac- ture.
Operation Tires and wheels Maximum tire inflation pressure 1 Maximum permissible tire inflation pressure For illustration purposes only. Actual data on tires are specific to each vehicle and may vary from data shown in above illustration. This is the maximum permissible tire inflation pressure for the tire.
Page 330
Quality grades can be found, where appli- cable, on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear Traction Temperature All passenger car tires must conform to federal safety requirements in addition to these grades. Treadwear The treadwear grade is a comparative rat- ing based on the wear rate of the tire when tested under controlled conditions on a...
Operation Tires and wheels Temperature The temperature grades are A (the high- est), B, and C, representing the tire’s resis- tance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Tire and loading terminology Accessory weight The combined weight (in excess of those standard items which may be replaced) of automatic transmission, power steering, power brakes, power windows, power seats, radio, and heater, to the extent that these items are available as factory-installed equipment (whether installed or not).
Page 333
Operation Tires and wheels GVWR (Gross Vehicle Weight Rating) This is the maximum permissible vehicle weight of the fully loaded vehicle (weight of the vehicle including all options, passen- gers, fuel, and cargo and, if applicable, trailer tongue load). It is indicated on certification label located on the driver’s door B-pillar.
Page 334
TIN (Tire Identification Number) Unique identifier which facilitates efforts by tire manufacturers to notify purchasers in recall situations or other safety matters concerning tires and gives purchases the means to easily identify such tires. The TIN is comprised of “Manufacturer’s identifica- tion mark”, “Tire size”, “Tire type code”, and “Date of manufacture”.
Wheels could become loose if not tightened with a torque of 80 lb-ft (110 Nm). Only use genuine Mercedes-Benz wheel bolts specified for your vehicle’s rims. For information on wheel change, see the “Practical hints” section ( page 392) and...
Winter driving Before the onset of winter, have your vehicle winterized at an authorized Mercedes-Benz Center. This service includes: Checking anticorrosion and antifreeze concentration. Adding of cleaning concentrate to the water of the windshield and headlamp cleaning* system. Add MB Windshield Washer Concentrate “MB SummerFit”...
The tires or the vehicle could be damaged as a result. Only use snow chains that are approved by Mercedes-Benz. Any authorized Mercedes-Benz Center will be glad to advise you on this subject. Use of snow chains may be prohibited depending on location.
Failure to have the vehicle maintained in accordance with the Maintenance Booklet and the maintenance service indicator at the designated times/mileage will result in vehicle damage not covered by the Mercedes-Benz Limited Warranty. Maintenance service indicator message The maintenance service indicator message will notify you when the next maintenance service is due.
Service A Exceeded By XXX Days Service A Exceeded By X Day In addition, a signal sounds when the message appears. Any authorized Mercedes-Benz Center will reset the maintenance service indicator following a completed maintenance service. Calling up the maintenance service...
Only reset if the proper maintenance service has been performed. Resetting the system without performing the proper maintenance service as called for by the maintenance service indicator will result in engine damage and/or other vehicle damage not covered by the Mercedes-Benz Limited Warranty. Operation Maintenance...
Damaged areas need to be re-undercoated. Your vehicle has been treated at the factory with a wax-base rustproofing in the body cavities which will last for the lifetime of the vehicle. Post-production treatment is neither necessary nor recommended by Mercedes-Benz because of the possibility...
Page 342
We have selected car-care products and compiled recommendations which are specially matched to our vehicles and which always reflect the latest technology. You can obtain Mercedes-Benz approved car-care products at an authorized Mercedes-Benz Center. Scratches, corrosive deposits, corrosion or damage due to negligent or incorrect care cannot always be removed or repaired with the car-care products recommended here.
Page 343
Hand-wash Do not use hot water or wash your vehicle in direct sunlight. Use only a mild car wash detergent, such as Mercedes-Benz approved Car Shampoo. Thoroughly spray the vehicle with a diffused jet of water. Direct only a very weak spray towards the ventilation intake.
Page 344
Mercedes-Benz Center. Headlamps, tail lamps, side makers, turn signal lenses Use a mild car wash detergent, such as Mercedes-Benz approved Car Shampoo, with plenty of water. Only use window cleaners that are suitable for plastic lamp lenses. Window cleaning solu- tions which are not suitable may damage the plastic lamp lenses of the headlamps.
Page 345
To do so, please drive your vehicle for several minutes to allow the brakes to dry. When applying Mercedes-Benz approved Tire Care and Mercedes-Benz approved Wheel Care products, take care not to spray them on the brake discs.
Page 346
Otherwise you may scratch or damage the surface. Hard plastic trim items Use Mercedes-Benz approved Interior Care, a soft, lint-free cloth and apply with light pressure. Never apply strong force and only use a soft, non-scratching cloth when cleaning the surface.
Page 347
Warning! Only use seat covers which have been tested and approved by Mercedes-Benz for your vehicle model. Using other seat covers may interfere with or prevent the deploy- ment of the head-thorax air bags. Contact an authorized Mercedes-Benz Center for availability.
Practical hints What to do if … Where will I find...? Unlocking/locking in an emergency Opening/closing in an emergency Replacing SmartKey batteries Replacing bulbs Replacing wiper blades Flat tire Battery Jump starting Towing the vehicle Fuses...
Read and observe messages in the multifunction display ( page 360). Have the system checked at an authorized Mercedes-Benz Center as soon as possible. Failure to follow these instructions in- creases the risk of an accident. When the voltage is above this value again, the ABS is operational again an the ABS indicator lamp should go out.
Page 350
12 mph (20 km/h). When the ABS indicator lamp goes ® out, the ABS, the ESP , and the BAS are available again. Continue driving with added caution. Have the system checked at an authorized Mercedes-Benz Center as soon as possible.
Page 351
Apply the parking brake ( page 59). Read and observe messages in the dis- play ( page 360). Contact an authorized Mercedes-Benz Center. Do not add brake fluid! This will not solve the problem.
Page 352
(emergency operation) mode. Practical hints What to do if … Have the vehicle checked as soon as pos- sible by an authorized Mercedes-Benz Center. An on-board diagnostic connector is used by the service station to link the vehicle to the shop diagnostics system. It allows the...
Page 353
Observe additional messages that may appear in the multifunction display ( page 363). Have the system checked at an authorized Mercedes-Benz Center as soon as possible. When driving off, apply as little throttle as possible. While driving, ease up on the accelerator.
Page 354
Problem < The red seat belt telltale comes on for a maximum of 6 seconds after starting the engine. < Your hear a warning chime for a maximum of 6 seconds after starting the engine. < The red seat belt telltale comes on while the vehicle is standing still and the engine is running or during driving.
Page 355
Practical hints What to do if … Problem < During driving the red seat belt telltale flashes and you addition- ally hear an intermittent warning chime sound with increasing in- tensity. After 60 seconds with an unfastened seat belt, the warning chime stops sounding and the seat belt telltale illuminates continuously.
Page 356
In the event a malfunction of the SRS is indicated as outlined above, the SRS may not be operational. For your safety, we strongly recommend that you contact an authorized Mercedes-Benz Center immediately to have the system checked; Possible cause/consequence Suggested solution The fuel cap is not closed properly.
Page 357
Read and observe messages in the multifunction display. Have the TPMS checked by an authorized Mercedes-Benz Center. After the malfunction has been remedied, the combination low tire pressure/TPMS malfunction telltale goes out after a few minutes of...
Page 358
Warning! Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recom- mended by the vehicle manufacturer on the Tire and Loading Information placard on the driver’s door B-pillar ( page 307) or, if available, the tire inflation pressure label on the inside of the fuel filler flap ( page 291).
Possible cause/consequence Suggested solution The system is malfunctioning. Have the system checked as soon as possible by an authorized Mercedes-Benz Center. Also read and observe any messages in the multifunction display and follow corrective steps ( page 365).
Page 360
If the front passenger front air bag off indicator lamp remains out, have the system checked as soon as possible by an authorized Mercedes-Benz Center. Do not transport a child on the passenger seat until the system has been repaired.
Mercedes-Benz Center. Failure to repair condition noted may cause damage not covered by the Mercedes-Benz Limited Warranty, or result in property dam- age or personal injury.
Page 362
No messages will be displayed if either the instrument cluster or the multifunction dis- play is inoperative. Contact your nearest authorized Mercedes-Benz Center. Switching on ignition ( page 37) causes all instrument cluster lamps (except high beam headlamp indicator lamp and turn signal indica- tor lamps unless activated) as well as the multi- function display to come on.
Continue driving with added caution. Wheels may lock during hard braking, reducing steering capability. Have the system checked at an authorized Mercedes-Benz Center as soon as possible. Have the cruise control checked by an authorized Mercedes-Benz Center. Continue driving with added caution.
Page 364
When the message disappears, the ESP available again. Continue driving with added caution. Have the system checked at an authorized Mercedes-Benz Center as soon as possible. Continue driving with added caution. ® is operational again and the message in Have the generator (alternator) and battery checked.
Page 365
SRS may not be operational. For your safety, we strongly recommend that you contact an authorized Mercedes-Benz Center immedi- ately to have the system checked; otherwise the SRS may not be deployed when needed in an accident, which could result in serious...
Page 366
Display message Possible cause/consequence Front-passenger The passenger front air bag and the Airbag Enabled passenger-side knee bag are See Operator’s activated while driving even though a Manual child, small individual, or object below the system’s weight threshold is on the passenger seat, or the passenger seat is empty.
Page 367
OCS ( page 71), the 75 indicator lamp will remain illuminated or go out. If above conditions are not met, the system is not working properly. Have the system checked as soon as possible by an authorized Mercedes-Benz Center. remains illuminated with an adult occupant...
Page 368
Display message Possible cause/consequence Front-passenger The passenger front air bag and the Airbag Disabled passenger-side knee bag are See Operator’s deactivated while driving even though Manual an adult or someone larger than a small individual is occupying the front passenger seat. Forces acting on the seat may make the system sense a decrease in weight.
Page 369
OCS ( page 71), the 75 indicator lamp will remain illuminated or go out. If above conditions are not met, the system is not working properly. Have the system checked as soon as possible by an authorized Mercedes-Benz Center. remains illuminated with an adult occupant...
Page 370
Make sure that the correct tire inflation pressure is set for each tire. Then restart the Run Flat Indicator* ( page 316). Have the Run Flat Indicator* checked by an authorized Mercedes-Benz Center. Carefully bring the vehicle to a halt, avoiding abrupt steering and braking maneuvers. Observe the traffic situation around you.
Page 371
Continued driving with a flat tire will cause excessive heat build-up and possibly a fire. Possible solution Have the TPMS checked by an authorized Mercedes-Benz Center. Have the TPMS checked by an authorized Mercedes-Benz Center.
Page 372
Symbol messages Display symbol Display message Ê • Possible cause/consequence Possible solution This message will appear whenever the trunk lid is open. You are driving with the hood open. Risk of accident! You are driving with one or more doors open. The cooling fan for the coolant is malfunctioning.
Page 373
Do not continue to drive. Otherwise, the engine will overheat due to an inoperative water pump which may result in damage to the engine. Contact an authorized Mercedes-Benz Center. If it is in order: Contact an Mercedes-Benz Center immediately. Adjust driving to be consis- tent with reduced braking responsive- ness.
Page 374
Turn off the engine. Apply the parking brake ( page 59). Do not drive any further. Contact an authorized Mercedes-Benz Center. Have the brake pads replaced as soon as possible. If you find that the brake fluid in the brake...
Page 375
Contact an authorized Mercedes-Benz Center. If it is intact: Wait for the message to disappear before restarting the engine. Doing otherwise could result in serious engine damage that is not covered by the Mercedes-Benz Limited Warranty. (Continued on next page)
Page 376
If the temperature rises again: Contact an authorized Mercedes-Benz Center immediately. The engine should not be operated with the coolant temperature above 248°F (120°C). Doing so may cause serious engine damage which is not covered by the Mercedes-Benz Limited Warranty.
Page 377
Do not ignore the low engine coolant level warning. Extended driving with this message and symbol displayed may cause serious engine damage not covered by the Mercedes-Benz Limited Warranty. Do not drive without sufficient amount of coolant in the cooling system. The engine will overheat, causing major engine damage.
Page 378
What to do if … Possible solution Have the electronic systems checked by an authorized Mercedes-Benz Center. Check the engine oil level ( page 296) and add engine oil as required ( page 299). If you must add engine oil frequently, have...
Page 379
( page 296). Have the measuring system checked by an authorized Mercedes-Benz Center. Engine oil level warnings should not be ignored. Extended driving with the symbol displayed could result in serious engine damage that is not covered by the Mercedes-Benz Limited Warranty.
Page 380
Add engine oil ( page 299) and check the engine oil level ( page 296). Refuel at the next gas station ( page 291). Check the fuel cap ( page 291). Close the fuel cap. Have the fuel system checked by an autho- rized Mercedes-Benz Center.
Page 381
Practical hints What to do if … Display symbol Display message Retractable Roof Operation Please Wait Retractable Roof Lowering Retractable Roof Operation Only At Standstill Retractable Roof Not Opened/Closed Completely Possible cause/consequence Possible solution The on-board voltage is too low. Start the engine.
Page 382
The headlamps switch on automati- cally. To switch off the headlamps (U.S. vehicles only): Practical hints What to do if … Contact an authorized Mercedes-Benz Center. Remove the SmartKey from the starter switch. Contact an authorized Mercedes-Benz Center as soon as possible.
Page 383
The left high beam lamp (halogen headlamps)/high beam flasher lamp (Bi-Xenon* headlamps) is malfunctioning. Contact an authorized Mercedes-Benz Center as soon as possible. Contact an authorized Mercedes-Benz Center as soon as possible. Contact an authorized Mercedes-Benz Center as soon as possible.
Page 384
( page 400). Replace the bulb as soon as possible ( page 400). Replace the bulb as soon as possible ( page 400). Replace the bulb as soon as possible ( page 400). Contact an authorized Mercedes-Benz Center as soon as possible.
Page 385
LEDs have stopped working. Replace the bulb as soon as possible ( page 400). Contact an authorized Mercedes-Benz Center as soon as possible. Replace the bulb as soon as possible ( page 400).
Page 386
SmartKey from the starter switch. The parking lamps remain switched on. Practical hints What to do if … Contact an authorized Mercedes-Benz Center as soon as possible. Contact an authorized Mercedes-Benz Center as soon as possible. Contact an authorized Mercedes-Benz Center as soon as possible.
Page 387
The right rear turn signal is malfunc- tioning. A backup bulb has been brought into use. Contact an authorized Mercedes-Benz Center as soon as possible. Contact an authorized Mercedes-Benz Center as soon as possible. Replace the bulb as soon as possible ( page 400).
Page 388
Display symbol Display messages Please correct tire pressure. Tire Pressure Caution - Tire Defect Tire Pressure Check Tires Warning! Do not drive with a flat tire. A flat tire affects the ability to steer or brake the vehicle. You may lose control of the vehicle. Continued driving with a flat tire will cause excessive heat build-up and possibly a fire.
Page 389
Practical hints What to do if … Display symbol Display message PHONE OFF Trunk Partition Open Top Up Washer Fluid Possible cause/consequence Possible solution This display appears if button s or t on the multifunction steer- ing wheel is pressed and the vehicle is not equipped with a telephone*.
Where will I find...? First aid kit The first aid kit is stored in a parcel net behind the driver’s seat. Check expiration dates and contents for completeness at least once a year and replace missing/expired items. Vehicle tool kit, vehicle jack The vehicle tool kit is stored in a storage compartment under the trunk floor.
Page 391
Practical hints Where will I find...? 1 Collapsible wheel chock 2 Vehicle jack 3 Protective wrap 4 Alignment bolt 5 Towing eye bolt 6 Wheel wrench 7 Valve extractor 8 Electric air pump Vehicles with TIREFIT* 1 TIREFIT kit 2 Vehicle jack 3 Collapsible wheel chock 4 Towing eye bolt 5 Alignment bolt...
Page 392
The vehicle jack is located in the storage compartment underneath the trunk floor. Storage position Remove vehicle jack from its compartment. Turn crank handle in the direction of arrow as far as it will go. Operational position Turn crank handle clockwise. Before storing the vehicle jack in its compartment: It should be fully collapsed.
Practical hints Where will I find...? Tilt both plates upward 1. Fold the lower plate outward 2. Guide the tabs of the lower plate all the way into the openings of the base plate 3. For information on where to place wheel chocks when changing a wheel, see “Lifting the vehicle”...
Unscrew the valve insert from the valve and allow the air to escape. It may take a few minutes for the collapsible tire to deflate completely. Screw the valve insert back into the valve. Screw the valve cap back on the valve. Pull the protective wrap provided with the vehicle tool kit over the spare wheel.
Practical hints Unlocking/locking in an emergency Unlocking the vehicle If you cannot unlock the vehicle with the SmartKey, open the driver’s door and the trunk using the mechanical key. Unlocking the vehicle with the mechanical key and opening the driver’s door or the trunk will trigger the anti-theft alarm system ( page 90).
Unlocking and opening the trunk A minimum height clearance of 5.78 ft (1.76 m) is required to open the trunk lid. 1 Unlocking 2 Handle 3 Mechanical key Insert mechanical key 3 into the trunk lid lock until it stops. Turn mechanical key 3 counterclock- wise to position 1 until it stops, and simultaneously...
Practical hints Unlocking/locking in an emergency 1 Locking 2 Mechanical key Insert mechanical key 2 into the driver’s door lock until it stops. Turn mechanical key 2 clockwise to position 1. The driver’s door is locked. This procedure does not arm the anti-theft alarm system, nor does it lock the fuel filler flap and the storage compartments.
Manually closing the retractable hardtop is a complicated and technically demanding pro- cedure and should only be performed by an authorized Mercedes-Benz Center or quali- fied technician. Attempting to manually close the retractable hardtop may cause damage to the retractable hardtop and/or personal injury.
When replacing batteries, always replace both batteries. The required replacement batteries are available at any Mercedes-Benz Center. Replacement batteries: Lithium, type CR 2025 or equivalent. Remove the mechanical key from the SmartKey ( page 394).
Page 400
3 Batteries 4 Contact springs Pull out batteries 3. Using a lint-free cloth, insert new batteries 3 under contact springs 4 with the positive terminal (+) side facing up. Return battery compartment 2 ( page 398) into the housing until it locks into place.
Have headlamps checked and readjusted at regular intervals and when a bulb has been replaced. Contact an authorized Mercedes-Benz Center for headlamp adjustment. If the headlamps are fogged up on the inside as a result of high humidity, driving the vehicle a short distance with the lights on should clear up the fogging.
Page 402
H7 (55 W) front fog lamp* Vehicles with Bi-Xenon* headlamps: Low beam and high beam use the same D2S-35W lamp. Do not replace the Bi-Xenon* bulbs yourself. Contact an authorized Mercedes-Benz Center. Practical hints Replacing bulbs Lamp Type 5 Parking and standing...
Page 403
Front and rear side marker lamps Parking/standing lamps in the tail lamp assemblies Do not replace the LEDs yourself. You could otherwise damage the LEDs or parts of the vehicle. Only have the LEDs replaced by an authorized Mercedes-Benz Center.
Replacing bulbs for front lamps Before you start to replace a bulb for a front lamp, do the following first: Turn the exterior lamp switch to position M ( page 109). Open the hood ( page 294). 1 Housing cover for low beam (halogen headlamps only) Housing cover for Bi-Xenon* head- lamps.
Practical hints Replacing bulbs Low beam bulb (Halogen headlamps only) Turn housing cover 1 counterclock- wise and remove. Turn bulb socket 5 with the bulb counterclockwise and remove. Pull the bulb out of bulb socket 5. Press the new bulb into bulb socket 5. Place bulb socket 5 back into the lamp and turn it clockwise.
Page 406
Fold corresponding trim to side. Turn the respective bulb socket coun- terclockwise and remove. Press gently onto the bulb and turn counterclockwise out of its bulb sock- Press the new bulb gently into its bulb socket and turn clockwise. Reinstall the bulb socket and turn clockwise until it engages.
For your convenience, we recommend that you have this work carried out by an authorized Mercedes-Benz Center. Placing wiper arms in vertical position 1 Wiper arms Turn the SmartKey in the starter switch to position 1 ( page 37).
Removing wiper blades Do not pull on the wiper blade inserts. They could tear. Fold the wiper arms forward until they engage. 1 Wiper blade 2 Tabs 3 Attachment 4 Cover Press tabs 2 together and tilt wiper blade 1 in direction of arrow. Tabs 2 on both recesses of attachment 3 are detached.
Do not drive the vehicle under such circum- stances. Contact the nearest Mercedes-Benz Center for assistance or call Roadside Assistance. Foreign objects (e.g. screws or nails) should not be removed from the tire.
Page 410
Warning! Take care not to allow the contents of TIREFIT to come in contact with hair, eyes or clothing. TIREFIT is harmful if inhaled, swallowed or absorbed through the skin – causes skin, eye and respiratory irritation. Any contact with eyes or skin should be flushed immediately with plenty of water.
Page 411
Practical hints Flat tire Version 1 1 TIREFIT container 2 Notch 3 Electric air pump switch 4 Electrical plug 5 Air hose 6 Flange 7 Flap Version 2 1 TIREFIT container 2 Notch 3 Electric air pump switch 4 Electrical plug 5 Air hose 6 Flange Open flap 7 on the electric air pump...
Page 412
Version 1 a Vent screw b Pressure gauge Close vent screw a on pressure gauge b (version 1 only). Screw filler hose 8 onto tire valve 9 ( page 410). Insert electrical plug 4 ( page 410) into the cigarette lighter ( page 256). Turn the SmartKey in the starter switch to position 1 ( page 37).
Page 413
In this case, TIREFIT cannot properly seal the tire. Do not drive the vehicle. Contact the nearest Mercedes-Benz Center or call Roadside Assistance. After attaining a tire inflation pressure of 26 psi (1.8 bar), press 0 on electric air pump switch 3 ( page 410).
Page 414
Practical hints Flat tire Drive to the nearest qualified work- shop, e.g. an authorized Mercedes-Benz Center, to have the damaged tire replaced. Recommended duration of use: A maximum of 300 miles (500 km) at 50 mph (80 km/h) or below with the recommended tire inflation pressure.
50 mph (80 km/h). Drive to the nearest Mercedes-Benz Center as soon as possible to have the spare wheel replaced with a regular road wheel. Never operate the vehicle with more than one spare wheel mounted.
Page 416
Warning! The jack is designed exclusively for jacking up the vehicle at the jack take-up brackets built into either side of the vehicle. To help avoid personal injury, use the jack only to lift the vehicle during a wheel change. Never get beneath the vehicle while it is supported by the jack.
Page 417
Practical hints Flat tire Jack up the vehicle until the wheel is a maximum of 1.2 in (3 cm) from the ground. Warning! The jack is intended only for lifting the vehicle briefly for wheel changes. It is not suited for performing maintenance work under the vehicle.
Page 418
Never apply oil or grease to wheel bolts. Damaged wheel hub threads should be repaired immediately. Do not continue to drive under these circumstances! Contact an authorized Mercedes-Benz Center or call Roadside Assistance. Incorrect wheel bolts or improperly tight- ened wheel bolts can cause the wheel to come off.
Page 419
Practical hints Flat tire Warning! Use only genuine Mercedes-Benz wheel bolts. Other wheel bolts may come loose. Do not tighten the wheel bolts when the vehicle is raised. Otherwise the vehicle could fall off the jack. Unscrew the alignment bolt, install last wheel bolt and tighten slightly.
Page 420
Press I on electric air pump switch 2. The electric air pump switches on and inflates the collapsible tire. Inflate the collapsible tire to approxi- mately 51 psi (3.5 bar). This takes about 5 minutes. Air hose 4 and union nut 5 can become hot during inflation.
Page 421
Practical hints Flat tire Lowering the vehicle Warning! Inflate the collapsible tire using the electric pump ( page 418) before lowering the vehicle. Lower vehicle by turning the crank counterclockwise until vehicle is resting fully on its own weight. Remove the jack. 1 - 5 Wheel bolts Tighten the five wheel bolts evenly in the direction of the arrow, following the...
After driving in emergency mode, you must have the rims inspected by an authorized Mercedes-Benz Center to check if they are suitable for further use. The failed tire must be replaced in any case.
SmartKey is in the starter switch. Otherwise the alternator and other electronic components could be severely damaged. Have the battery checked regularly by an authorized Mercedes-Benz Center. Refer to Maintenance Booklet for maintenance intervals or contact an authorized Mercedes-Benz Center for further information.
Disconnecting the battery Warning! With a disconnected battery you will no longer be able to turn the SmartKey in the starter switch automatic transmission*: the gear se- lector lever will remain locked in position P 1 Water tray 2 Lock Always disconnect the battery in the order described below.
Warning! Never charge a battery while still installed in the vehicle unless the accessory battery charge unit approved by Mercedes-Benz is being used. Gases may escape during charg- ing and cause explosions that may result in paint damage, corrosion or personal injury.
Reconnecting the battery Always connect the battery in the order described below. Otherwise the vehicle’s electronics can be damaged. Turn off all electrical consumers. Connect the battery positive lead 2 ( page 422) and fasten its cover. Connect the battery negative lead 3 ( page 422).
Do not attempt to start the engine using a battery quick charge unit. If the engine does not run after several unsuccessful starting attempts, have it checked at the nearest authorized Mercedes-Benz Center. Excessive unburned fuel generated by repeated failed starting attempts may damage the catalytic converter and may present a fire risk.
Page 428
Remove the jumper cables first from negative terminals 3 and 4 and then from positive terminals 2 and 1. You can now switch on the headlamps. Have the battery checked at the nearest authorized Mercedes-Benz Center.
Practical hints Towing the vehicle Mercedes-Benz recommends that the vehi- cle be transported with all wheels off the ground using flatbed or appropriate wheel lift/dolly equipment. Vehicles with automatic transmission*: Do not tow-start vehicle. Use flatbed or wheel lift/dolly equipment with the SmartKey in the starter switch in position 0.
Towing of the vehicle should only be done using the properly installed towing eye bolt. Never attach a tow cable, tow rope or tow rod to the vehicle chassis, frame or suspension parts. When towing the vehicle with all wheels on the ground, please note the following: With the automatic central locking activated and the SmartKey in starter switch position 2, the...
Page 431
Practical hints Towing the vehicle Removing Press mark on cover 1. Cover 1 springs open at the top right corner. Pull at the protruding part of cover 1 and fold cover down to reveal the threaded hole for the towing eye bolt. Do not disconnect cover 1 from its check strap.
Page 432
Removing Press mark on cover 1. Cover 1 springs open at the top. Pull at the protruding part of cover 1 and fold cover down to reveal the threaded hole for the towing eye bolt. Do not disconnect cover 1 from its check strap.
(recognizable by its color or the fuse rating given on the fuse) of the amperage recommended in the fuse chart. Any Mercedes-Benz Center will be glad to advise you on this subject. If a newly inserted fuse blows again, have the cause determined and rectified by an authorized Mercedes-Benz Center.
Fuse box in passenger compartment 1 Fuse box cover Do not use sharp objects such as a screw driver to open fuse box cover 1 in the dashboard, as this could damage it. Opening Open the driver’s door. Insert flat, blunt object as a lever into recess on the edge of cover 1 at the position indicated by the arrow.
Technical data Parts service Warranty coverage Identification labels Layout of poly-V-belt drive Engine Rims and tires Electrical system Main Dimensions Weights Fuels, coolants, lubricants, etc.
Therefore, Genuine Mercedes-Benz Parts should be installed. The use of non-genuine Mercedes-Benz parts and accessories not authorized by Mercedes-Benz could damage the vehicle, which is not covered by the Mercedes-Benz Limited Warranty, or could compromise the vehicle’s durability or safety.
Emission System Warranty Emission Performance Warranty California, Maine, Massachusetts, and Vermont Emission Control Systems Warranty Replacement parts and accessories are covered by the Mercedes-Benz Parts and Accessories warranties, copies of which are available at any authorized Mercedes-Benz Center. Technical data Warranty coverage...
Technical data Identification labels 1 Certification label (on driver’s door B-pillar) The Vehicle Identification Number (VIN) can be found in the following locations: on the certification label on the center tunnel, under a carpet cover behind the passenger seat ( page 439) on the lower edge of the windshield ( page 439) Example certification label (U.S.
Page 440
4 VIN 5 Engine number (engraved on engine) 6 VIN (lower edge of windshield) 7 Emission control information label, includes both federal and California certification exhaust emission standards When ordering parts, please specify vehicle identification and engine numbers. Technical data Identification labels...
1-4-3-6-2-5 Poly-V-belt 2404 mm The quoted data apply only to the standard vehicle. Contact an authorized Mercedes-Benz Center for the corresponding data of all special bodies and special equipment. Premium fuel required. Performance may vary with fuel octane rating. SLK 350 (171.456)
MOE = Mercedes-Benz Original Extended (tires with limited run-flat characteristics) original equipment tires Using tires other than those approved by Mercedes-Benz may result in damage that is not covered by the Mercedes-Benz Limited Warranty. For information on driving with MOExtended tires, see “MOExtended system*”...
Same size tires Model Rims (light alloy) Wheel offset Winter tires Radial-ply tires Not available as factory equipment. Must be used in conjunction with Tire Pressure Monitoring System (U.S. vehicles) or Run Flat Indicator* (Canada vehicles) only. SLK 280 7 J x 16 H2 1.34 in (34 mm) 205/55 R16 91H M+S.
Page 445
Wheel offset 1,2,3 Winter tires Radial-ply tires Not available as factory equipment. For use with snow chains contact an authorized Mercedes-Benz Center. SLK 280 (Sport Package*) SLK 350 (Sport Package*) SLK 55 AMG 7.5 J x 17 H2 1.46 in (37 mm) 205/50 R17 89H M+S.
Mixed size tires Model Front axle: Rims (light alloy) Wheel offset Summer tires Rear axle: Rims (light alloy) Wheel offset Summer tires Radial-ply tires Must be used in conjunction with Tire Pressure Monitoring System (U.S. vehicles) or Run Flat Indicator* (Canada vehicles) only. Must not be used with snow chains.
Page 447
Technical data Rims and tires Model Front axle: AMG rims (light alloy) Wheel offset Summer tires Rear axle: AMG rims (light alloy) Wheel offset Summer tires Radial-ply tires Must be used in conjunction with Tire Pressure Monitoring System (U.S. vehicles) or Run Flat Indicator* (Canada vehicles) only. Must not be used with snow chains.
Spare wheel Model Rim (light alloy) Wheel offset Collapsible tire Must not be used with snow chains. Please compare the recommended tire inflation pressure for your vehicle with the tire inflation pressure on the yellow label located on the spare wheel rim. If the tire inflation pressure on the yellow label on the spare wheel rim differs from the values given in this Operator’s Manual, inflate the...
This vehicle is not designed to carry items on its roof. Roof rails and any roof-mounted de- vices, unless expressly approved by Mercedes-Benz for use on this vehicle model, must not be used as they will damage the vehicle and retractable hardtop.
Therefore, only use products tested and approved by Mercedes-Benz. Please refer to the Factory Approved Service Products pamphlet (USA only), or inquire at an authorized Mercedes-Benz Center. Model Engine with oil filter All models Automatic transmission* SLK 280, SLK 350 9.5 US qt (9.0 l)
Page 453
Technical data Fuels, coolants, lubricants, etc. Model Power steering All models Front wheel hubs All models Brake system All models Cooling system SLK 280 SLK 350 SLK 55 AMG Fuel tank All models including a reserve of SLK 280, SLK 350 SLK 55 AMG Air conditioning system All models...
Engine oil additives Do not blend oil additives with engine oil. They may damage the engine. Damage or mal- functions resulting from blending oil additives are not covered by the Mercedes-Benz Limited Warranty. Technical data Fuels, coolants, lubricants, etc. Air conditioning refrigerant...
Therefore, the brake fluid must be replaced regularly. Refer to your vehicle’s Maintenance Booklet for replacement interval. Only brake fluid approved by Mercedes-Benz is recommended. Any authorized Mercedes-Benz Center will provide you with additional information. Premium unleaded gasoline Warning! Gasoline is highly flammable and poisonous.
Damage or malfunction resulting from poor fuel quality or from blending additional fuel additives other than those tested and approved by us for use on Mercedes-Benz vehicles are not covered by the Mercedes-Benz Limited Warranty.
Add premixed coolant solution only. Adding water and MB 325.0 Anticorrosion/Antifreeze separately from each other, could cause engine damage not covered by the Mercedes-Benz Limited Warranty. If the antifreeze mixture is effective to -35°F (-37°C), the boiling point of the cool- ant in the pressurized cooling system is reached at approximately 266°F (130°C).
Page 458
Before the start of the winter season (or once a year in hot southern regions), you should have the anticorrosion/antifreeze concentration checked. The coolant is also regularly checked each time you bring your vehicle to an authorized Mercedes-Benz Center for service.
Technical data Fuels, coolants, lubricants, etc. Windshield washer system and headlamp cleaning system* Both the windshield washer system and headlamp cleaning system* are supplied from the windshield washer reservoir. The windshield washer reservoir has a capacity of approximately 7.4 US qt (7.0 l). Refill the reservoir with MB Windshield Washer Concentrate “MB SummerFit”...
ABS 84 Indicator lamp 348, 349 Messages in the multifunction display 362 Accelerator position, automatic transmission 159 Accessory weight 331 Accident 58 Air bags 66 Children in the vehicle 79 Front 69 Head-thorax 70 Knee bag 70 Occupant Classification System (OCS) 71 Passenger 69 Passenger front air bag off indicator...
Page 461
Index Gear shifting malfunctions 167 Gearshift pattern 52 Kickdown 159 Kickdown, manual shift program* 167 Manual shift program* 165 Program mode selector switch 161 Shifting procedure 156 Steering wheel gearshift control one-touch gearshifting* 163 Backup lamp Messages in the multifunction display 383 Replacing bulbs 402 Bar 331...
Page 462
Climate control 172 Air conditioning refrigerant 452 Air conditioning, Cooling 180 Air recirculation mode 178 Air vents 172 Air volume 177 Control panel 174 Defrosting 170, 177 Residual heat utilization 181 Switching on/off 175 Temperature 175 Clock 120 Cockpit 24 Cold tire inflation pressure 331 Collapsible tire (spare wheel) 447 Collapsible wheel chock 391...
Page 463
Index Digital speedometer 128 Dimensions, Vehicle 449 Dipstick see Oil dipstick Direction of rotation (Tires) 307 Display text see Messages in the multi- function display Displays Digital speedometer 128 Maintenance service indicator 337 Multifunction display 121 Outside temperature 128 Symbol messages 371 Text messages 362 Vehicle status message memory 135 Vehicle status messages 360...
Page 464
Emergency Tensioning Device see ETD Emission control 289 Information label 439 System warranties 10 Engine Cleaning 342 Compartment 294 Malfunction indicator lamp 27, 351 Number 439 Poly-V-belt layout 440 Starting 51 Tachometer 119 Technical data 441 Turning off 61 Engine oil 296, 453 Adding 299 Additives 453 Checking level (Control system) 296...
Page 465
Index Garage door opener* 270 Gasoline see Fuel GAWR 331 Gear range Automatic transmission 160 Limiting 160 Shifting into optimal 163, 165 Gear selector lever 155 Gearshift pattern 155 Position 156, 157 Shifting procedure 156 Gear selector lever one-touch gearshifting Automatic transmission 162 Global locking/unlocking see SmartKey Glove box 253...
Page 466
Labels 438 Lamp in center console 358 Lamps in instrument cluster 348 Lamps, indicator and warning ABS 348, 349 Battery (SmartKey) 97 Brakes 350 CHECK ENGINE 351 ® 87, 352 Fuel reserve 355 Instrument cluster 356 Passenger front air bag off 74, 358 Seat belts 353–354 SRS 65, 355 Language in multifunction display (Control...
Page 467
Index Manual transmission 153 Driving 53 Gearshift pattern 51 Starting with SmartKey 51 Maximum inflation pressure 332 Maximum load rating 332 Maximum loaded vehicle weight 332 Mechanical key see SmartKey Memory function* 107 Menus see Control system menus Messages in the multifunction display see Multifunction display messages Mirror lamp* see Sun visors Mirrors 168...
Page 468
Occupant Classification System see OCS Occupant distribution 332 Occupant safety 64 OCS 71 Passenger front air bag off indicator lamp 74 Seat belts 48, 68 SRS 64 OCS 71 Self-test 75 Oil see Engine oil One-touch gearshifting Gear selector lever 162 Steering wheel gearshift control* 163 Operating safety 16, 193...
Page 469
Index RACETIMER see Control system menus, Radio Operation (Audio system) 199 Operation (Control system) 133 Satellite* 134 Radio transmitters, control and operation 287 Reading lamps 117 Rear view mirrors see Mirrors Rear window defroster 170 Recommended inflation pressure 332 Recovery services for stolen vehicle (Tele Aid*) 269 Refrigerant (Air conditioning) 453 Refueling 291...
Page 470
Selective setting see SmartKey Selector lever see Gear selector lever Selector lever* lock 52 Self-test OCS 75 Service Information 12 Maintenance Booklet 12 Service and warranty Booklet 437 Information 10 Service life (Tires) 305 Service system Maintenance service indicator 337 Parts service 436 Settings menu (Control system) 136 Shelf behind roll bar 254...
Page 471
Index Storage compartments 32, 253 Armrest 32, 253 Between seat backrests 32, 254 Cup holder 32, 255 Door pockets 32 Glove box 32, 253 Parcel net 32, 254 Storage tray 32 Telephone* 253 Telephone* compartment 32 Trunk 32 Storing tires 306 Summer opening* Power windows 238 Retractable hardtop 244...
Page 472
Tire ply composition and material used 333 Tire speed rating 323, 333 Tire terminology 331 TIREFIT* Instructions for use 408 Vehicle tool kit 389, 390 Tires 304, 442 Cleaning 306 Direction of rotation 307 Driving instructions 283 Flat tire 408 Important guidelines 304 Inflating with air pump 418 Low tire pressure telltale 356...
Page 473
Index Useful features Ashtray 255 Cigarette lighter 256 Cup holder 255 Floormat (Driver’s side only) 258 Garage door opener* 270 Heated steering wheel* 276 Parcel net 254 Power outlet 257 Storage compartments, interior 253 Tele Aid* 262 Vehicle Battery 302, 422 Bulbs 400 Fuses 432 Individual settings (Control...
Need help?
Do you have a question about the 2008 SLK 350 and is the answer not in the manual?
Questions and answers