Advertisement
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Steinberg UR22mkII
Summary of Contents for Steinberg UR22mkII
-
Page 2: Table Of Contents
UR22mkII. Connections..........10 As implied by the “mkII” designation, the UR22mkII is Configuring Audio Driver Settings on the DAW an evolved descendant of the UR22. The most Software ............12 prominent new features are iOS support and a loopback function. -
Page 3: Panel Controls And Terminals
[INPUT 2 HI-Z] switch. Doing so can damage the Adjust the gain knobs so that the [PEAK] indicator connected device and/or the unit itself. flashes briefly at the loudest input volume. 4 [+48V] indicator Lights up when the [+48V] switch (phantom power) is turned on. UR22mkII Operation Manual... - Page 4 Operation of this control knob is independent from that of the [OUTPUT] knob. ) [PHONES ] jack For connection to a set of stereo headphones. ! [OUTPUT] knob Adjusts the output signal level of the [LINE OUTPUT] jacks. UR22mkII Operation Manual...
-
Page 5: Rear Panel
USB interface. such as an iPad. (The UR22mkII does not include a Failing to do so may result in the computer freezing or USB power adapter or USB mobile battery.) shutting down, as well as corruption or even loss of data. - Page 6 OFF when it is not required. NOTICE When using phantom power, observe the following to prevent noise and possible damage to UR22mkII or connected equipment. • Do not connect or disconnect any devices while the phantom power switch is turned to ON.
-
Page 7: Software
DAW software. If the loopback function is How to Select Windows on while you are monitoring input signals form the UR22mkII Click the upper tabs to select the desired window. via DAW software, it will cause loud noise. This is because an infinite loop of the audio signal is generated between the UR22mkII and the DAW software. - Page 8 When using the loopback function, turn off the monitor functions on your DAW software. If the loopback function is on while you are monitoring input signals form the UR22mkII via DAW software, it will cause loud noise. This is because an infinite loop of the audio signal is generated between the UR22mkII and the DAW software.
- Page 9 [Devices] [Device Setup...]. About Window Click [Control Panel] in [Steinberg Indicates the version and copyright information of UR22mkII] in the menu on the left side of the audio driver. the window. HINT How to Select the Sample Rate Select the sample rate in [Audio MIDI Setup] window.
-
Page 10: Using The Ur22Mkii
• (Windows only) Connect the USB cable to the same USB terminal that you used when installing the Yamaha Steinberg USB Driver. If you connect the USB cable to a different USB terminal, the Yamaha Steinberg USB Driver will be installed again. -
Page 11: Connecting To A Computer
• The Apple iPad Camera Connection Kit or Lightning to USB Camera Adapter are required when connecting the UR22mkII with an iPad. • A USB mobile battery or a power adapter is required when connecting the UR22mkII with an iPad. • The loopback function is unavailable when connecting the UR22mkII with an iPad. -
Page 12: Configuring Audio Driver Settings On The Daw Software
This section provides examples of connecting the guitar, using an existing template in Cubase (default UR22mkII to a computer. The explanations in this settings). section assume that the Yamaha Steinberg USB Driver has been properly installed according to the Cubase Series Programs “Getting Started”... - Page 13 Using the UR22mkII Select UR22mkII ports for [Device Port] on Select the input routing in the inspector. both the inputs and outputs tabs. When a microphone is connected to the [MIC/LINE 1] jack: Inputs Tab Click the track name on the left side of the project window.
- Page 14 Using the UR22mkII Click [] at the top of the screen to start Programs other than Cubase Series recording. Launch the DAW software. Adjust the input signal level of the microphone or guitar with the [INPUT GAIN] knob on the device.
-
Page 15: Using The Ur22Mkii With Connected Midi Device
Track name Confirm the connection between the MIDI device and UR22mkII. Connect the MIDI IN of the UR22mkII to the MIDI OUT jack of the MIDI device with a MIDI cable. To MIDI IN In the window that appears below, select [All MIDI Inputs] or [Steinberg UR22mkII-1]. -
Page 16: Troubleshooting
Troubleshooting Power does not Has the Yamaha Steinberg USB Driver been installed properly? turn on. Refer to the Getting Started instructions to complete the Yamaha Steinberg USB Driver installation. (The USB indicator is off or flashing To confirm the installation, follow these steps: continuously, even 1. - Page 17 From the Cubase series menu, open the [Devices] [Device Setup…] [VST Audio System], then confirm that the [Yamaha Steinberg USB ASIO] (Windows) or [Steinberg UR22mkII] (Mac) is selected on the [ASIO Driver]. Windows Was the power of the device turned on before starting the DAW software? Before starting the DAW software, connect the device to a computer and turn on the power of the device.
- Page 18 Troubleshooting Unusual sound Does your computer satisfy the system requirements? (noise, interruption, Confirm the system requirements. For the latest information, see the Steinberg website below. or distortion) http://www.steinberg.net/ Are you recording or playing long continuous sections of audio? The audio data processing capabilities of your computer will depend on a number of factors including CPU speed and access to external devices.
-
Page 19: Appendix
Appendix Appendix Block Diagrams UR22mkII Operation Manual... - Page 20 Steinberg Website http://www.steinberg.net/ Manual Development Department © 2015 Yamaha Corporation Published 9/2015 MW-A0...
Need help?
Do you have a question about the UR22mkII and is the answer not in the manual?
Questions and answers