Page 1
WIDE LCD MONITOR RECEIVER KVT-M707 SCRN MODE V.SEL V.OFF AV OUT SEL OPEN/CLOSE VOLUME KENWOOD TOUCH SCREEN CONTROL L 13942296513 AUTO Panel assy Destination K : ATT Destination K (A64-3568-02) Destination E : ATT Destination E (A64-3569-02) DC cord (Destination K)
KVT-M707/M707Y COMPONENTS DESCRIPTION 3 7 63 1515 0 VIDEO CONTROL UNIT (X14-954x-xx) Ref. No. Application / Function Operation / Condition / Compatibility DC-DC CONTROLLER DC-DC circuit control/driving 5V REGULATOR Power supply for BU5.0V 3.3V REGULATOR Power supply for P-ON 3.3V IC101 E2PROM Non-volatile memory...
Page 4
KVT-M707/M707Y COMPONENTS DESCRIPTION 3 7 63 1515 0 Ref. No. Application / Function Operation / Condition / Compatibility For BU DET BUFFER For switching transistor gate drive For BU DET POWER SUPPLY Switching transistor for flyback For BU DET POWER SUPPLY Switching transistor for voltage reduction chopper Q20,21 For BU DET...
Page 5
KVT-M707/M707Y COMPONENTS DESCRIPTION 3 7 63 1515 0 ELECTRIC UNIT (X34-353x-xx) Ref. No. Application / Function Operation / Condition / Compatibility IC50 REGULATOR 8.4V for audio is generated from BU14V ±9.0V for 5V pre-out is generated from BU14V IC52 POWER SUPPLY CONVERTER IC54 REGULATOR 5V for video is generated from BU14V...
Page 6
KVT-M707/M707Y COMPONENTS DESCRIPTION 3 7 63 1515 0 Ref. No. Application / Function Operation / Condition / Compatibility Q8~11 P-CONT CONTROL P-CONT circuit control BU DET SW Comes ON when power supply voltage is about 8.8V or higher EXT-AMP CONTROL External amp control SURGE VOLTAGE DET Comes ON when Q15 is ON...
Page 7
KVT-M707/M707Y COMPONENTS DESCRIPTION 3 7 63 1515 0 VIDEO UNIT (X35-4470-10) Ref. No. Application / Function Operation / Condition / Compatibility INVERTER CONTROL Control and driving of inverter circuit for backlight IC101 TIMING CONTROLLER LCD module control IC205 3-STATE BUFFER Switch for start pulse switching IC303 PLL LPF...
KVT-M707/M707Y MICROCOMPUTER’S TERMINAL DESCRIPTION 3 7 63 1515 0 SYSTEM µ-COM : IC103 on X14- (VIDEO CONTROL UNIT) Truth Value Pin No. Pin Name Application Processing Operation Description Table OSD DATA Data to OSDC-IC OSD CLK Clock to OSDC-IC Data to EEPROM Data from TUNER µ-com SYS SDATA Data to TUNER µ-com...
Page 9
KVT-M707/M707Y MICROCOMPUTER’S TERMINAL DESCRIPTION 3 7 63 1515 0 Truth Value Pin No. Pin Name Application Processing Operation Description Table CLKOUT ON/OFF control to Tuner µ-com (X34-) SYS ON H: ON, L: OFF Request to Tuner µ-com (X34-) SYS MREQ Request from Tuner µ-com (X34-) SYS SREQ γ...
Page 10
KVT-M707/M707Y MICROCOMPUTER’S TERMINAL DESCRIPTION 3 7 63 1515 0 Truth Value Pin No. Pin Name Application Processing Operation Description Table For γ automatic adjustment VCOM IN AUTO DIM Auto dimmer Panel key (4 parts) switching of key processing in KEY1 synchronization with TV mechanism horizontal detection XDATA Touch panel input (X-direction)
Page 11
KVT-M707/M707Y MICROCOMPUTER’S TERMINAL DESCRIPTION 3 7 63 1515 0 e Screen Position Adjustment Value y Touch Panel Control Timing NTSC HPOS Default Wait Detection XData YData 2.0msec 2.0msec 2.0msec 2.0msec Full OSD Lo, Lo, Lo, Lo NAVI Lo, Lo, Lo, Lo Lo, Lo, Lo, Lo Lo, Lo, Lo, Lo read...
Page 12
KVT-M707/M707Y MICROCOMPUTER’S TERMINAL DESCRIPTION 3 7 63 1515 0 TUNER µ-COM: IC303 on X34- (ELECTRIC UNIT) Truth Value Pin No. Pin Name Application Processing Operation Description Table TV CON Startup request to TV unit H: TV unit ON, L: TV unit OFF TUN SCL Front-end I2C clock output terminal NAVI1 RX...
Page 13
KVT-M707/M707Y MICROCOMPUTER’S TERMINAL DESCRIPTION 3 7 63 1515 0 Truth Value Pin No. Pin Name Application Processing Operation Description Table CLKOUT MUTE AVOUT MUTE for AV OUT L: MUTE ON, H: Normal AUDIO SW1 A LX/NAVI1/SW3 (or TV)/AVIN1 audio switching (for main) Refer to Truth Value Table AUDIO SW1 B LX/NAVI1/SW3 (or TV)/AVIN1 audio switching (for main)
Page 14
KVT-M707/M707Y MICROCOMPUTER’S TERMINAL DESCRIPTION 3 7 63 1515 0 Truth Value Pin No. Pin Name Application Processing Operation Description Table Request from system µ-com SYS MREQ Request to system µ-com SYS SREQ AVDD AVSS AVREF DC ERR DC offset error detection Low at detection Normal: 1.6V, TEL MUTE: 1V or lower LINE MUTE...
Page 15
* Input is reversed by transistor before entering selector. Rear view y Destination setting for OEM !3 Video Selector 5 (IC416) Destination TYPE0 TYPE1 L 13942296513 KENWOOD brand VISUAL SW5 1 VISUAL SW5 2 Output OEM1 OEM2 AVIN2 Test when driving in EU...
KVT-M707/M707Y TEST MODE 3 7 63 1515 0 • Security Info (BLANK: E2PROM not written, ON/OFF: Nor- How to enter the test mode mal condition (ON/OFF security is set), ERROR: E2PROM While pressing [SRC] key and [ATT] key at the same time, write abnormal) reset the unit.
Page 17
KVT-M707/M707Y TEST MODE 3 7 63 1515 0 • Chroma IC adjustment screen (Item Setting) → Write on • E2PROM write normal/abnormal ending is displayed on screen. EEPROM. • Writing region does not clear EEPROM Chroma data. Setting Item: Tint adjustment (00h~FFh) EEPROM chroma data is cleared by the Clear key in the Phase adjustment (00h~FFh) Service screen.
Page 18
KVT-M707/M707Y TEST MODE 3 7 63 1515 0 Remote Controller BEEP Control • Using NA-R300 (SW: AUD), the following operations will be • Beep will be sound regardless of destinations conducted (Normal operation other than the following) (When Standby sourcing, Beep will not be sound as PWIC limitation item.) Key code Item...
Page 19
KVT-M707/M707Y TEST MODE 3 7 63 1515 0 Panel Mechanism Specification to turn motor driver ON with no slide • At Full Open, angle is vertical and Slide is at the very back. mechanism • Panel Mecha Slide/Angle will be in 3 steps. •...
KVT-M707/M707Y TEST MODE 3 7 63 1515 0 Screen Specifications • During the Test Mode, when Graphic Screen is selected, Test Mode Main screen is displayed. Test Mode Main screen MECHA Chroma Chroma Source Set Up Audio Information Service Touch Chroma Hposi Auto...
Page 21
KVT-M707/M707Y TEST MODE 3 7 63 1515 0 Service Screen Serial Number Input Screen • Service information is displayed/cleared. • The serial number for each set is written. • EEPROM Chroma data is cleared. • DC Offset detection information is displayed/cleared. Serial Number Input Screen ∗∗∗...
Page 22
KVT-M707/M707Y TEST MODE 3 7 63 1515 0 Touch Screen Hposi Screen • Touch variances in different sets are adjusted. • Horizontal position for each screen is adjusted. (Refer to a Touch the markers for 3 points in order. When EEPROM separate sheet for details.) OK screen is displayed, adjustment is complete.
Page 23
KVT-M707/M707Y TEST MODE 3 7 63 1515 0 Chroma Screen Chroma Func Screen • Chroma data adjustment will be conducted. • For function jigs. Chroma data adjustment will be conducted. • Adjustment is conducted with a remote controller (Audio • Adjustment method and screen are the same as Chroma. SW).
Page 24
KVT-M707/M707Y ADJUSTMENT 3 7 63 1515 0 OSD Clock and OSD HSYNC Phase Adjustment (X14-) (X14-) Condition IC301 pin11 HSYNC Video source: VIDEO Input: NTSC video (Video: Color bar) (X14-) Screen mode: FULL IC301 pin2 OSC IN Adjustment Procedure 1. When starting up in Test Mode, it starts up with VIDEO source (FULL).
Page 25
KVT-M707/M707Y ADJUSTMENT 3 7 63 1515 0 PAL Demodulation Axis Adjustment Method (Destination E Only) Condition Ch1: Input signal Input Signal: Color bar (PAL signal) Remote Controller Operation Method Ch2: : Final selection B output DIRECT: End 7: Adjustment item switching 8: Adjustment value UP Ch3: 0: Adjustment value DOWN...
KVT-M707/M707Y ADJUSTMENT 3 7 63 1515 0 Freerun Frequency Adjustment Horizontal Display Start Position and Adjustment Procedure OSD Display Position Adjustment 1. Timing Controller IC101 Screen adjustment key: HPOSI SYNC IN (pin1) TP154, HSYNC IN (pin2) TP153 and VDB Go to te next adjustment screen IN (pin5) TP149 are to be made no input.
KVT-M707/M707Y ADJUSTMENT 3 7 63 1515 0 Adjustment Procedure Touch Panel Adjustment 1. Press HPOSI in the Test Mode Menu screen. Adjustment Procedure 2. Adjust Horizontal display start position for the following four: 1. Press the Touch Key in the Menu screen of the Test Mode Graphic, TV, VIDEO, and Navigation.
Page 28
KVT-M707/M707Y PC BOARD (COMPONENT SIDE VIEW) 3 7 63 1515 0 VIDEO CONTROL UNIT X14-954x-xx (J76-0090-12) J601 R335 R309 W603 W303 R310 R313 X401 C412 R314 R429 C432 Q403 R403 C427 R423 R433 C437 R407 C426 C436 W520 C424 R504 IC403 D401 C421...
Page 30
KVT-M707/M707Y PC BOARD (FOIL SIDE VIEW) 3 7 63 1515 0 VIDEO CONTROL UNIT X14-954x-xx (J76-0090-12) L 13942296513 u163...
Page 31
KVT-M707/M707Y 3 7 63 1515 0 SUB-CIRCUIT UNIT X16-3020-10 A/2 (J76-0093-12) J101 X16 B/2 D217 L 13942296513 R214 u163 Refer to the schematic diagram for the values of resistors and capacitors.
Page 44
KVT-M707/M707Y 3 7 63 1515 0 VIDEO UNIT (X35-4470-10) (A/3) CN100 TP134 L112 A+5.0V A+5V A+5V 10uH A+5.0V TP135 V GND V GND TP127 D GND LED-R LED-R D108 D GND LED-G LED-G SW 12V OPEN/CLOSE W128 TP128 SW+18.5V SW+18.5V A+3.3V A+3.3V TP131...
Page 45
KVT-M707/M707Y 3 7 63 1515 0 (X35- ) (C/3) CN601 : OZ964ISN-C D1,2,7 UDZS5.6B OPEN IC101 MN5814UB 1SS355 DGND IC205 TC7WH126FU-F D4,5,9,108-110 S601 IC303 NJM2107F-ZB DA204U OPEN/ A+5V IC401 TPS850 MA2S784-F CLOSE D8,104,105,411 D GND CN101 Q1,5,105,106,203 AVRM1608120M6A D GND D GND 2SC4081 D106...
Page 46
KVT-M707/M707Y 3 7 63 1515 0 to DC CORD ELECTRIC UNIT (X34-353x-xx) FUSE C232 BU14V 1000P Q14,15 SW14V Q55,59 SURGE 14V POWER VOLTAGE A8V POWER SUPPLY SW SUPPLY SW 3900u16 IC50 REGULATOR IC50 470K EXT-AMP OP AM IC200 CONTROL L MUTE 13.8V 8.3V AOUT...
Page 47
KVT-M707/M707Y 3 7 63 1515 0 FRONT REAR CENTER CAMERA PRE OUT AV OUT VIDEO J200 J202 IC50,54 IC52 IC100 IC150,200-202 IC151 IC203,204,405,500 IC251 IC300 IC301 C235 C236 IC302 IC303 1000P 1000P IC400-402,407,408 C234 C237 R267 2200P 2200P IC403 VOLTAGE IC404 OP AMP OP AMP...
Page 49
KVT-M707/M707Y 3 7 63 1515 0 VISUAL LINE SIGNAL LINE GND LINE 4.8V 4.8V B LINE B LINE R400 C417 1.4V ELECTRIC UNIT IC403 L300 IC404 (X34- ) (B/2) 10uH BU5V VIDEO ∗ SYNC 1.5V 1.4V CN250 A250 SEPARATOR CN253 IFGND IFGND IFGND...
KVT-M707/M707Y EXPLODED VIEW (MAIN UNIT) 3 7 63 1515 0 M2x4 :N09-6355-05 φ2x5 :N09-6236-05 M2X3 :N09-6232-05 FLAT WASHER :N19-2022-04 φ2x6 :N80-2006-43 φ2.6x6 (X35 C/3) :N86-2606-48 PME1 FPC3 (X35-447 A/3) L 13942296513 LCD1 FPC1 FPC2 FPC1 (X14-954) (X35 B/3) (X16 B/2) (X16-302) u163 Parts with the exploded numbers larger than 700 are not supplied.
Page 52
KVT-M707/M707Y EXPLODED VIEW (MECHANISM) 3 7 63 1515 0 M2.6X3.7 :N09-6062-15 M2X2.2(BLK) :N09-6063-25 M2X3.5(BLK) :N09-6064-25 M1.7X2.5 :N09-6065-25 M2X3.2 :N09-6066-25 M1.7X2.2 :N09-6111-25 WASHER :N19-2127-14 (X16-B/2) RETAINING RING :N29-0206-04 L 13942296513 (X16-313 A/2) u163 Parts with the exploded numbers larger than 700 are not supplied.
Page 53
KVT-M707/M707Y EXPLODED VIEW (HIDEAWAY UNIT) 3 7 63 1515 0 SIZE AAA BATTERY (NOT SUPPLIED) L 13942296513 (X34-) (X34 B/2) (X86-393) (X34-353) φ2.6x14 N84-2614-48 φ2.6x6 N89-2606-48 φ3x8 N89-3008-43 φ3x8 N09-6135-05 M3x20 N35-3020-48 u163 Depends on the modles. Refer to the parts list. Parts with the exploded numbers larger than 700 are not supplied.
H54-3539-03 ITEM CARTON CASE D13-2256-14 GEAR J19-5207-23 HOLDER D13-2257-14 GEAR J19-5235-14 HOLDER E : Europe K : North America K : KVT-M707 E1 : KVT-M707 E2 : KVT-M707Y Indicates safety critical components. M : Other Areas W : Without Europe...
Page 55
CHIP C 0.10UF CE32BF1E101M CHIP EL 100UF 25WV C327 CK73GB1H104K CHIP C 0.10UF Indicates safety critical components. E : Europe K : North America K : KVT-M707 E1 : KVT-M707 E2 : KVT-M707Y M : Other Areas W : Without Europe...
Page 56
1.0UF RN73GH1J683D CHIP R D 1/16W C560 CK73GB1H104K CHIP C 0.10UF E1E2 E : Europe K : North America K : KVT-M707 E1 : KVT-M707 E2 : KVT-M707Y Indicates safety critical components. M : Other Areas W : Without Europe...
Page 57
J 1/10W RK73GB2A123J CHIP R J 1/10W R406 RK73GB2A103J CHIP R J 1/10W E : Europe K : North America K : KVT-M707 E1 : KVT-M707 E2 : KVT-M707Y Indicates safety critical components. M : Other Areas W : Without Europe...
Page 58
STZ6.2N ZENER DIODE R632 RK73GB2A471J CHIP R J 1/10W D629-631 AVRM1608270MAB VARISTOR E : Europe K : North America K : KVT-M707 E1 : KVT-M707 E2 : KVT-M707Y Indicates safety critical components. M : Other Areas W : Without Europe...
Page 59
DTC124EUA DIGITAL TRANSISTOR R234,235 RK73GB2A222J CHIP R 2.2K J 1/10W 2SC5566-E TRANSISTOR E : Europe K : North America K : KVT-M707 E1 : KVT-M707 E2 : KVT-M707Y Indicates safety critical components. M : Other Areas W : Without Europe...
Page 60
16WV C104 CD04AS1C101M ELECTRO 100UF 16WV C242 CK73GB1H103K CHIP C 0.010UF K E : Europe K : North America K : KVT-M707 E1 : KVT-M707 E2 : KVT-M707Y Indicates safety critical components. M : Other Areas W : Without Europe...
Page 61
RK73GB2A104J CHIP R 100K J 1/10W C500 CK73GB1H103K CHIP C 0.010UF K E : Europe K : North America K : KVT-M707 E1 : KVT-M707 E2 : KVT-M707Y Indicates safety critical components. M : Other Areas W : Without Europe...
Page 62
RK73GH2A512D CHIP R 5.1K D 1/10W R244 RK73GB2A361J CHIP R J 1/10W E : Europe K : North America K : KVT-M707 E1 : KVT-M707 E2 : KVT-M707Y Indicates safety critical components. M : Other Areas W : Without Europe...
Page 63
J 1/10W R358-360 RK73GB2A104J CHIP R 100K J 1/10W D1-8 M1F60-5063 DIODE E : Europe K : North America K : KVT-M707 E1 : KVT-M707 E2 : KVT-M707Y Indicates safety critical components. M : Other Areas W : Without Europe...
Page 64
Q204-207 DTC323TU DIGITAL TRANSISTOR IC203,204 BA3121F ANALOGUE IC Q208 DTA144EUA DIGITAL TRANSISTOR E : Europe K : North America K : KVT-M707 E1 : KVT-M707 E2 : KVT-M707Y Indicates safety critical components. M : Other Areas W : Without Europe...
Page 65
J 1/16W C142 CC73GCH1H560J CHIP C 56PF RK73HB1J512J CHIP R 5.1K J 1/16W E : Europe K : North America K : KVT-M707 E1 : KVT-M707 E2 : KVT-M707Y Indicates safety critical components. M : Other Areas W : Without Europe...
Page 66
J 1/16W Q101 DTA114TUA DIGITAL TRANSISTOR R210,211 RK73HB1J202J CHIP R 2.0K J 1/16W E : Europe K : North America K : KVT-M707 E1 : KVT-M707 E2 : KVT-M707Y Indicates safety critical components. M : Other Areas W : Without Europe...
Page 67
DIGITAL TRANSISTOR Q501 DTC124EE DIGITAL TRANSISTOR Q502,503 PUMD13 DUAL TRANSISTOR L 13942296513 u163 E : Europe K : North America K : KVT-M707 E1 : KVT-M707 E2 : KVT-M707Y Indicates safety critical components. M : Other Areas W : Without Europe...
Main unit ............1.7kg / 3.7 lbs ............ 530kHz~1700kHz (10kHz) Hideaway unit ..........1.1kg / 2.4 lbs Usable sensitivity ............28dBµ KENWOOD follows a policy of continuous advancements in LW (E destination) development. For this reason specifications may be changed Frequency range ......... 153kHz~281kHz without notice.