Related Manuals for Sony Digital HDVS HDC-900
Summary of Contents for Sony Digital HDVS HDC-900
- Page 1 HD COLOR CAMERA HDC-900 HDC-900/L HDC-910 HDC-910/L HDC-930 HDC-950 HD CCD BLOCK ADAPTOR HKC-T950 MAINTENANCE MANUAL 1st Edition (Revised 4)
- Page 2 ! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.
- Page 3 For HDC-900/910/930/950 For HDC-900/910/930/950 CLASS 1 CAUTION LASER PRODUCT LASER KLASSE 1 Use of controls or adjustments or performance of PRODUKT procedures other than those specified herein may result in hazardous radiation exposure. This HD color camera is classified as a CLASS 1 LASER PRODUCT.
- Page 4 For HDC-900/910/930/950 CAUTION ADVARSEL Danger of explosion if battery is incorrectly replaced. Lithiumbatteri - Eksplosjonsfare. Ved utskifting benyttes kun batteri som anbefalt av apparatfabrikanten. Replace only with the same or equivalent type recommended by the manufacturer. Brukt batteri returneres Dispose of used batteries according to the apparatleverandøren.
- Page 5 For the customers in the Netherlands For the customers in Japan Voor de klanten in Nederland Hoe u de batterijen moet verwijderen, leest u in de tekst van deze handleiding. Gooi de batterij niet weg maar lever deze in als klein chemisch afval (KCA).
-
Page 7: Table Of Contents
Table of Contents Manual Structure Purpose of this manual ..................5 (E) Related manuals ....................5 (E) Contents ....................... 6 (E) 1. Service Overview 1-1. Optional Fixtures ................... 1-1 (E) 1-2. Cleaning of Connector/Cable ..............1-2 (E) 1-3. Circuit Description ................1-3 (E) 1-3-1. - Page 8 2-6. Replacing the Boards ................2-7 (E) 2-6-1. SDI-49 Board ............... 2-7 (E) 2-6-2. RX-28 Board ................ 2-9 (E) 2-6-3. MB-883 Board ..............2-11 (E) 2-6-4. CN-2073 Board ..............2-13 (E) 3. Replacement of Main Parts (HDC-950/930, HKC-T950) 3-1. Replacing the CCD Unit ............... 3-1 (E) 3-2.
- Page 9 4. Replacement of CCD Unit Boards 4-1. CN-1961 Board ..................4-1 (E) 4-2. RP-114 Board ..................4-2 (E) 4-3. DR-412/492 Board ................4-2 (E) 4-4. TG-214 Board ..................4-2 (E) 4-5. CN-1947/2329 Board ................4-3 (E) 4-6. DU-69 Board ..................4-3 (E) 4-7.
- Page 10 6-5-7. Auto-iris Adjustment ............6-16 (E) 6-5-8. Pedestal Level Adjustment ..........6-17 (E) 6-5-9. Flare Adjustment ..............6-17 (E) 6-5-10. Gamma Correction Adjustment ......... 6-18 (E) 6-5-11. Knee Point/Knee Slope Adjustment ........6-18 (E) 6-5-12. White Clip Level Adjustment ..........6-19 (E) 6-5-13.
-
Page 11: Manual Structure
..System Manual (Available on request) This manual is necessary for connection and operation of this unit and other peripheral equipment. If this manual is required, please contact your local Sony Sales Office/Service Center. 5 (E) -
Page 12: Contents
..“Semiconductor Pin Assignments” CD-ROM (Available on request) This “Semiconductor Pin Assignments” CD-ROM allows you to search for semiconductors used in B&P Company equipment. Semiconductors that cannot be searched for on this CD-ROM are listed in the maintenance manual for the corresponding unit. -
Page 13: Service Overview
Section 1 Service Overview 1-1. Optional Fixtures Name Sony Part No. Remarks EX-738 Board A-8327-351-A For extension of plug-in boards Alignment sleeve remover HC-001 J-6480-010-A For female connector Cotton swab —— Diameter about 4 mm Any available on the market... -
Page 14: Cleaning Of Connector/Cable
Tools Required sleeve in the straight line and turn it clockwise. . Alignment sleeve remover HC-001 (for female connector) Sony P/N: J-6480-010-A Insert the shorter nose end when removing/installing the alignment sleeve. Grasp not the shock absorber portion of the remover but the handle in use. -
Page 15: Circuit Description
The BI-145/150 board supplies the DC bias required for the alignment sleeve. the CCD. The CCD output is sent through a buffer to the (Alignment sleeve: Sony P/N 9-980-074-01) NR-69/73 board. The BI-145/150 board mounts horizontal clock drivers for the CCD and a reset gate driver. - Page 16 1-3. Circuit Description DU-69/RP-114 boards VDA-55 Board The DU-69 and RP-114 boards mount the RPN correction The R, G, and B signals and Y, P , and P signals input circuit for the CCD. from the DPR-154 board, and RET (Y/P ) signals input from the DAD-37 board are selected by the switch, passed VA-196 board...
- Page 17 1-3. Circuit Description SDI-49 board DAP-24 board The SDI-49 board converts the parallel Y/P signal The intercom signals and microphone signals in two multiplexed by the DAD-37 board to a serial digital signal channels each, which are sent from the AU-271 board, are and outputs it from the SERIAL OUT connector.
-
Page 18: Hkc-T950
1-3. Circuit Description 1-3-2. HKC-T950 AT-147 board (Cable adaptor) The AT-147 board consists of the control microcomputer IF-845 board (CCD block adaptor) and its peripheral circuit. The AT-147 board converts the The main line signal (RGB) input from the CCD block is control signal in the CCD block into the command that can adjusted in the output level and then sent through the 75 Z be sent/received using the cable and sends/receives it to/... -
Page 19: Description Of Ccd Block Number
1-4. Description of CCD Block Number 1-5. Notes on Flexible Card Wire 1-4. Description of CCD Block Number 1-5. Notes on Flexible Card Wire 1-5-1. Disconnecting/Connecting Flexible Every CCD unit has its own ID number called CCD block Card Wire number. -
Page 20: Forming Before Installation (Hdc-950/930)
1-5. Notes on Flexible Card Wire 1-6. Positioning Adjustment for Installing the Filter Knobs (HDC-950/930, HKC-T950) 1-6. Positioning Adjustment for 1-5-2. Forming Before Installation (HDC-950/ Installing the Filter Knobs 930) (HDC-950/930, HKC-T950) If using a new flexible card wire, be sure to hand-form it as shown in the figure before installation. -
Page 21: Notes On Replacement Of Circuit Board
EEPROM (NV-RAM) that is storing data inherent in the HKC-T950 board. The part number listed in “Spare Parts” is for EEPROM (NV-RAM) which is not programmed. If Board/Block For Part For Board replacement is needed, consult your Sony representatives. Replacement Replacement AT-146 —— —— AT-147 ——... -
Page 22: Disassembly Of Hdcz Connector
1-8. Disassembly of HDCZ Connector 1-8. Disassembly of HDCZ Connector 1. Remove the two screws and three setscrews. 2. Connect the plug to the VTR or camera. 3. Loosen the plug counterclockwise by pliers. 4. Disassemble as illustrated and unsolder. 1-10 (E) HDC-900/950 MM... - Page 23 1-9. How to Supply a Power of +12 V 1-9. How to Supply a Power of + + + + + 12 V AU-271 board suffix -13 and higher Set the switch S300 on the AU-271 board to ON, and set Each the model HDC-900/910 and HDC-950/930 can on the MIC POWER switch of AUDIO IN connector supply 12 V for MIC POWER to the microphone connect-...
-
Page 24: Version-Up Of Rom/At-130 Board
1-10. Version-Up of ROM/AT-130 Board 1-10. Version-Up of ROM/AT-130 Board The ROM (IC1 on the AT-130 board) version can be upgraded using the memory stick. Follow the procedure shown below. . Prepare the memory stick in which the upgraded program has been written. . - Page 25 1-10. Version-Up of ROM/AT-130 Board 4. The VERSION UP execution page is displayed as shown below. HDC-900/910 : Move the cursor to “AT VERSION UP” and then press the MENU SELECT switch toward the “ENTER” side. HDC-950/930 : Move the cursor to “AT VERSION UP” and then press the rotary encoder. CANCEL AT VERSION UP VERSION UP execution page...
-
Page 26: Note On Replacement Of Lithium Battery
4. Program the PLD (or ROM for PLD) with the Down- . The PLD internal data is controlled in the Sony Database load Tool software. Server under the name Project file (E_xxx_xxx_xx_xx). 5. Upon completion of programming, check that error . -
Page 27: Replacing The Fuse
1-13. Replacing the Fuse 1-13. Replacing the Fuse A fuse is critical parts to safe operation. Replace this component with Sony parts whose part numbers appear in this manual published by Sony. If not, this may cause a fire or electric shock. -
Page 29: Replacement Of Main Parts (Hdc-900/910)
Section 2 Replacement of Main Parts (HDC-900/910) 2-1. Replacing the CCD Unit 4. Remove the four hexagon-socket bolts, remove the four spring washers, and remove the front panel assembly. Never remove or install the CCD unit with the power turned on. Because touching internal harness to the cabinet or other printed circuit boards during replacement causes shorts or electric hazards. -
Page 30: Replacing The Filter Disk Unit
2-1. Replacing the CCD Unit 2-2. Replacing the Filter Disk Unit 2-2. Replacing the Filter Disk Unit 6. Remove the three screws, and remove the transporta- tion holder from the CCD unit for repair part HKC- 2-2-1. Filter Disk Unit C900R (optional). -
Page 31: Nd/Cc Filters
2. Remove the tow screws to remove retainers securing ND/CC Filter List the filter to be replaced. 3. Install a new filter using the screws and retainers Filter Fig. Type Sony P/N Orientation which were removed in procedure 2. Cross 9-939-645-01 Cut surface facing the lens... -
Page 32: Driver Board
2-2. Replacing the Filter Disk Unit 2-3. Replacing the Power Assembly 2-3. Replacing the Power Assembly 2-2-3. Driver Board 1. Remove the filter disk unit. (Refer to Section 2-2-1.) . To avoid electric hazards when disconnecting the power 2. Remove the four screws. 3. -
Page 33: Replacing The Fan
2-4. Replacing the Fan 2-4. Replacing the Fan 4. Remove the fan packing, and remove the fan. If the fan is out of order, the inside temperature of the unit Protrusions will rise. Touching the inside in this state may cause a Fan packing burn. -
Page 34: Replacing The Ccu Connector
2-5. Replacing the CCU Connector 2-5. Replacing the CCU Connector 3. Disconnect the connector CN13 of the MB-883 board and connector CN8 of the CN-1974 board. Optical cables used in the unit are very fragile. So do not bend or yank in handling. This causes a break in the cable. CN13 1. -
Page 35: Replacing The Boards
2-5. Replacing the CCU Connector 2-6. Replacing the Boards 2-6. Replacing the Boards 5. Remove the four screws, and remove the connector box. 2-6-1. SDI-49 Board Remove the four screws, and remove the CCU connec- tor. . Every electrical part mounted on the SDI-49 board cannot be replaced. - Page 36 2-6. Replacing the Boards 3. Remove the three screws, and remove the fiber box. 4. Remove the four screws, and remove the SDI unit box lid. 5. Disconnect the optical cable (blue). Fiber box 6. Disconnect the harness from the connector CN2 of the B2.6 x 5 B2.6 x 5 SDI-49 board, and disconnect the coaxial cables from...
-
Page 37: Board
2-6. Replacing the Boards [Notes|at|installation] 2-6-2. RX-28 Board . Before connecting the connection connector, clean the white optical contact at the tip of connector with alcohol. . Align the protrusion of the connector with the notch of . Every electrical part mounted on the RX-28 board the interconnection connector in connecting. - Page 38 2-6. Replacing the Boards [Notes|at|installation] 3. Disconnect the optical cable (white). . Before connecting the connection connector, clean the 4. Remove the four screws, and remove the RX-28 board. white optical contact at the tip of connector with alcohol. . Align the protrusion of the connector with the notch of RX-28 board the interconnection connector in connecting.
- Page 39 2-6. Replacing the Boards 3. Remove the four screws in the order of 4, 3, 2, 2-6-3. MB-883 Board and 1, and remove the protection cover. 1. Remove the SDI unit. (Refer to steps 1 and 2 of Section 2-6-1.) Optical cables used in the unit are very fragile.
- Page 40 2-6. Replacing the Boards 5. Remove the CN-1956 board. 7. Open the right side panel. (Refer to Section 1-4 of the Installation and Maintenance Manual.) 8. Pull out the plug-in boards (RE, AU, AT-130, SG, DAP, DAD, VDA, DPR, VA) along the groove of the board rail and remove.
-
Page 41: Cn-2073 Board
2-6. Replacing the Boards 2-6-4. CN-2073 Board 10. Remove the screw, and remove IF board. 1. Loosen the four screws, and remove the control panel assembly. 2. Disconnect the flexible card wire from the connector CN10 of the CN-1974 board, and disconnect the harness from connector CN2 of the CN-2073 board. - Page 42 2-6. Replacing the Boards 3. Open the memory stick cap, and remove the two screws. 4. Remove the CN-2073 board. The memory stick ejector will disconnect at the same time. Be careful not to lose it. CN-204 board Memory stick ejector P2.6 x 5 Memory stick cap 5.
-
Page 43: Replacement Of Main Parts (Hdc-950/930, Hkc-T950)
Section 3 Replacement of Main Parts (HDC-950/930, HKC-T950) 3-1. Replacing the CCD Unit 3. Remove the four hexagon-socket bolts, remove the four spring washers, and remove the front panel assembly. . Never remove or install the CCD unit with the power turned on. -
Page 44: Replacing The Filter Disk Unit
3-1. Replacing the CCD Unit 3-2. Replacing the Filter Disk Unit 3-2. Replacing the Filter Disk Unit 5. Remove the three screws, and remove the transporta- tion holder from the CCD unit for repair part HKC- 3-2-1. Filter Disk Unit C900R (optional). - Page 45 3-2. Replacing the Filter Disk Unit 4. Adjust the indication (ND, CC) of the filter knob to 7. Be sure that ND of the filter disk unit is correspond- coincide with respective ND, CC of the new filter disk ingly linked to the filter knob (ND) and do CC to (CC) unit, respectively as shown below.
-
Page 46: Nd/Cc Filters
1. Remove the filter disk unit. (Refer to Section 3-2-1.) ND/CC Filter List 2. Remove the tow screws to remove retainers securing the filter to be replaced. Filter Fig. Type Sony P/N Orientation 3. Install a new filter using the screws and retainers Cross 9-939-645-01 Cut surface which were removed in procedure 2. -
Page 47: Driver Board
3-2. Replacing the Filter Disk Unit 3-3. Replacing the AC/DC Converter Unit 3-3. Replacing the AC/DC Converter Unit 3-2-3. Driver Board 1. Remove the filter disk unit. (Refer to Section 3-2-1.) 1. Remove the inside panel. (Refer to Section 1-4 of the 2. - Page 48 3-3. Replacing the AC/DC Converter Unit 3. Remove the two screws, and remove the PC board 5. Slide the AC/DC converter to the arrow direction until upper rail to the arrow direction. the connector (white) fully can be recognized. 6. Disconnect the connector (white), and remove the AC/ DC converter.
-
Page 49: Replacing The Fan
3-4. Replacing the Fan 3-4. Replacing the Fan 3. Remove the two screws, supporting the fan assembly from the bottom side. Disconnect the connector (R FAN) of MB-882 board. If the fan is out of order, the inside temperature of the unit will rise. -
Page 50: Front Fan
3-4. Replacing the Fan 3-4-2. Front Fan 3. Disconnect the connector CN2 of RE-188 board. 4. Remove the two screws, and remove the RE-188 board. When you need to replace a fan, clean it beforehand on the 5. Remove the two screws, and remove the fan. parts of take in/take out for air. -
Page 51: Fan For Hkc-T950
3-4. Replacing the Fan 3-5. Replacing the Side Switches (SW-1014 Board) 3-5. Replacing the Side Switches 3-4-3. Fan for HKC-T950 (SW-1014 Board) When replacing the fan, replace the cushion pasted to the 1. Remove the front fan assembly. fan too. (Refer to Section 3-4-2.) Cushion : 3-690-767-0X 2. -
Page 52: Replacing The Vf Disp Switches (Sw-1016 Board)
3-5. Replacing the Side Switches (SW-1014 Board) 3-6. Replacing the VF DISP Switches (SW-1016 Board) 3-6. Replacing the VF DISP Switches 5. Remove the two screws and two blind plates, and (SW-1016 Board) remove the SW-1014 board. Desolder the switch to be replaced. -
Page 53: Replacing The Ccu Connector
3-6. Replacing the VF DISP Switches (SW-1016 Board) 3-7. Replacing the CCU Connector 3-7. Replacing the CCU Connector 4. Remove the two screws, and remove the VF DISP switch assembly. Optical cables used in the unit are very fragile. So do not Precision P2.6 x 5 bend or yank in handling. - Page 54 3-7. Replacing the CCU Connector 3. Disconnect the optical cables (yellow), and disconnect 6. Remove the five screws, and remove the CCU connec- the connector (CCU) from the connector of the MB- tor. 882 board. Mark MB-882 board Precision Connector ( CCU ) P2.6 x 3 B3 x 8 B3 x 8...
-
Page 55: Replacing The Tracker Connector
3-8. Replacing the TRACKER Connector 3-8. Replacing the TRACKER Connector 5. Remove the two screws, and remove the TRACKER connector. 1. Remove the AUDIO IN connector. (Refer to Section 6. Remove the drop protection sheet from the TRACKER 3-12-2.) connector. 2. -
Page 56: Replacing The Prompter Connector
3-9. Replacing the PROMPTER Connector 3-10. Replacing the VF Connector 3-10. Replacing the VF Connector 3-9. Replacing the PROMPTER Connector 1. Remove the front assembly. (Refer to steps 1 and 2 of Section 3-1.) 1. Remove the CN-1951 board. (Refer to steps 1 to 4 of Section 3-8.) If the HKC-T950 is installed, remove the cable adaptor 2. -
Page 57: Replacing The Test Out Connector
3-11. Replacing the TEST OUT Connector 3-12. Replacing the MIC Connector 3-11. Replacing the TEST OUT Connector 3-12. Replacing the MIC Connector 3-12-1. FRONT MIC Connector 1. Remove the front fan assembly. (Refer to Section 3-4- 2. Disconnect the connector (CN20) of MB-882 board. 1. -
Page 58: Replacing The Audio In Connector
3-12. Replacing the MIC Connector 3-12-2. Replacing the AUDIO IN Connector 5. Disconnect the connectors (CN1 and CN2) of CN- 2026 board. 1. Loosen six screws, and pull out MIC panel assembly. When pulling out a MIC panel assembly, pay full attention to the harnesses and or flexible card wires connected to the MIC panel assembly so that they are free from incurring any damages. -
Page 59: Replacing The Incom Connector
3-12. Replacing the MIC Connector 3-13. Replacing the INCOM Connector 3-13. Replacing the INCOM Connector 3. Remove the 4 screws first, and remove the AUDIO IN connector, pressing connector lever. 1. Remove the outside panel. (Refer to Section 1-4 of the Installation and Maintenance Manual.) AUDIO IN connector Levers... -
Page 60: Replacing The Boards
3-13. Replacing the INCOM Connector 3-14. Replacing the Boards 3-14. Replacing the Boards 4. Remove the two screws, and remove the INCOM1 connector or INCOM2 connector. 3-14-1. RX-28 Board Nuts INCOM1 . Every electrical part mounted on the RX-28 board connector cannot be replaced. -
Page 61: Board
3-14. Replacing the Boards [Notes|at|installation] 5. Remove the three screws, and remove the RX holder. . Before connecting the connection connector, clean the white optical contact at the tip of connector with alcohol. . Align the protrusion of the connector with the notch of the interconnection connector in connecting. - Page 62 3-14. Replacing the Boards 3-14-2. SDI-49 Board 6. Install the new SDI-49 board in the reverse order of steps 1 to 5. [Notes|at|installation] . Every electrical part mounted on the SDI-49 board . Before connecting the connection connector, clean the cannot be replaced.
-
Page 63: Cn-2018 Board
3-14. Replacing the Boards 3-14-3. CN-2018 Board 4. Remove the three screws, and remove the CN-2018 board. 1. Remove the inside panel. (Refer to Section 1-4 of the Installation and Maintenance Manual.) 2. Pull out the plug-in boards (RE, AU, AT, SG, DAP, DAD, VDA, DPR, VA) along the groove of the board rail and remove. -
Page 64: Cn-1964 Board
3-14. Replacing the Boards [Notes|at|installation] 3-14-4. CN-1964 Board . Before connecting the connection connector, clean the white optical contact at the tip of connector with alcohol. . Align the protrusion of the connector with the notch of Optical cables used in the unit are very fragile. So do not bend or yank in handling. -
Page 65: Board
3-14. Replacing the Boards 3-14-5. MB-882 Board 6. Disconnect the harnesses from connectors (VF, TOP SW, R FAN, REAR AUDIO, RM, POWER, REAR VIDEO, F-MIC, INSIDE SW, TEST, LENS) and Optical cables used in the unit are very fragile. So do not flexible card wire from (INCOM PANEL) of MB-882 bend or yank in handling. -
Page 66: Replacing The Components Of Hkc-T950
3-14. Replacing the Boards 3-15. Replacing the Components of HKC-T950 [Notes|at|installation] 3-15. Replacing the Components of HKC-T950 . Before connecting the connection connector, clean the white optical contact at the tip of connector with alcohol. . Align the protrusion of the connector with the notch of The HKC-T950 consists of the CCD block adaptor and the interconnection connector in connecting. -
Page 67: Removing/Installing The Handle Assembly
3-15-3. Replacing the Lens Cable Assembly Tool: Installation and removal tool (for bushing) (Sony Part number : J-6470-280-A) If using the CCD block adaptor with the handle assembly (If it is not available, use a pair of pliers or a similar detached, it is recommended to attach the chassis cover. - Page 68 3-15. Replacing the Components of HKC-T950 3-15-4. AT-146 Board Installing 1. Install the cord bushing to the lens cable as shown in 1. Remove the handle assembly of the CCD block the figure. adaptor. (Refer to Section 3-15-2.) 2. Remove the two screws, and remove the AT-146 When installing, ensure that the cord bushing is board.
- Page 69 3-15. Replacing the Components of HKC-T950 3-15-5. IF-845 Board 6. Remove the four screws on the bottom of the unit, and remove the fan block. 1. Remove the HDCZ cable from the CCD block adaptor. 2. Remove the AT-146 board. (Refer to Section 3-15-4.) At this time, since the fan harness is connected to IF- 3.
- Page 70 3-15. Replacing the Components of HKC-T950 7. Remove the two screws on both sides in the upper 8. Disconnect the connectors (CN3, CN12, CN14, CN13, portion and two screws of the lower portion of the CN15) of the IF-845 board, and connector (CN1) of separate plate (2) block, and the remove the separate the RE-202 board.
-
Page 71: Board
3-15. Replacing the Components of HKC-T950 [Notes|at|installation] 3-15-6. RE-202 Board . Tuck the harness of the fan to the back of the separate plate (2). 1. Remove the separate plate (2) block. (Refer to steps 1 . Take out the connection connector to the AT-146 board to 7 of Section 3-15-5 “IF-845 Board”.) from near center of the upper portion. -
Page 72: Cam Body Connector
3-15. Replacing the Components of HKC-T950 3-15-7. CAM BODY Connector 3-15-8. VIDEO OUT/LENS Connector 1. Remove the separate plate (2) block. (Refer to steps 1 1. Remove the separate plate (2) block. (Refer to steps 1 to 7 of Section 3-15-5 “IF-845 Board”.) to 7 of Section 3-15-5 “IF-845 Board”.) 2. -
Page 73: Replacement Of Ccd Unit Boards
Section 4 Replacement of CCD Unit Boards To replace the boards in the CCD unit, refer to Section 2-1 3. Disconnect the flexible card wires from the connector (HDC-900/910) or Section 3-1 (HDC-950/930) and (CN1) of the DR-412/492 board and connector (CN7) remove the CCD unit from the main unit to replace. -
Page 74: Board
4-2. RP-114 Board 4-3. DR-412/492 Board 4-4. TG-214 Board 4-2. RP-114 Board 4-3. DR-412/492 Board 1. Remove the CN-1961 board. (Refer to Section 4-1.) Every electrical part mounted on the RP-114 board cannot 2. Remove the RP-114 board. (Refer to Section 4-2.) be replaced. -
Page 75: Cn-1947/2329 Board
4-5. CN-1947/2329 Board 4-6. DU-69 Board 4-5. CN-1947/2329 Board 4-6. DU-69 Board 1. Remove the shield case (UPPER and LOWER). (Refer Every electrical part mounted on the CN-1947/2329 board to steps 1 and 2 of Section 4-1.) cannot be replaced. If there is any defective part, replace 2. -
Page 76: Board
4-7. PA-239 Board 4-8. NR-69/73 Board 4-7. PA-239 Board 4-8. NR-69/73 Board 1. Remove the CN-1961 board. (Refer to Section 4-1.) 2. Remove the RP-114 board. (Refer to Section 4-2.) Every electrical part mounted on the NR-69/73 board 3. Remove the DU-69 board. (Refer to Section 4-6.) cannot be replaced. -
Page 77: Service Menu
Section 5 SERVICE Menu In this section, describes the service menu (SERVICE menu) in the setup menu displayed on the view- finder. For other menus, refer to Section 3 of the Installation and Maintenance Manual. 5-1. Setup Menu The setup menu is used for selecting various setting values, items displayed on the viewfinder screen, the method of displaying, and adjustments. - Page 78 5-1. Setup Menu Equipment Required HDC-900/910 7-type viewfinder HDVF-700A/7700/C700W (or black-and-white monitor) Camera control unit HDCU-900/700A HDC-950/930 2-type viewfinder HDVF-20A (or black-and-white monitor) Camera control unit HDCU-900/950/700A, or AC adapter AC-550, etc. for supplying the power to the camera. 5-2 (E) HDC-900/950 MM...
- Page 79 5-1. Setup Menu Switches (HDC-900/910) DISPLAY switch : Displays characters and messages indicating the settings and operating status of the unit on the viewfinder screen. : Turns off all the displays on the viewfinder screen. MENU : Displays the setup menu on the viewfinder screen. MENU SELECT control Selects the items displayed on the viewfinder screen and changes settings.
- Page 80 5-1. Setup Menu Switches (HDC-950/930) DISPLAY switch : Displays characters and messages indicating the settings and operating status of the unit on the viewfinder screen. : Turns off all the displays on the viewfinder screen. MENU : Displays the setup menu on the viewfinder screen. Rotary Encoder Selects the items displayed on the viewfinder screen and changes settings.
-
Page 81: Top Menu
5-2. TOP Menu 5-2. TOP Menu The TOP menu is provided for indicating the whole configuration of the menu items. Displaying the TOP menu HDC-900/910 : Set the DISPLAY switch from “OFF” to “MENU” while pressing the MENU SELECT switch toward the “ENTER” side. HDC-950/930 : Set the DISPLAY switch from “OFF”... -
Page 82: Service Menu
5-3. SERVICE Menu 5-3. SERVICE Menu This menu consists of the adjustments and settings required during servicing such as RPN correction, etc. PIXEL page <PIXEL> MANUAL R MANUAL G MANUAL B APR AT ABB : Item Setting Description MANUAL R See below Perform the RPN correction manually for each channel. - Page 83 5-3. SERVICE Menu SETTING 1 page <SETTING 1> CC A COLOR : 3200 CC B COLOR : 3200 CC C COLOR : 4300 CC D COLOR : 6300 Item Setting Description CC A COLOR 3200 to 9900 Sets according to the color temperature of the CCD filters CC B COLOR (A, B, C, D).
- Page 84 5-3. SERVICE Menu PRE WHT CLIP page (Displays ROM Version 1.30 or higher) <PRE WHT CLIP> [R] [G] [B] PRE WHT CLIP: STORE DATA Item Setting Description PRE WHT CLIP 80 to 7F Sets the pre white clip level. (Refer to Section 5-5.) STORE DATA See below Stores the setting value of the pre white clip level.
-
Page 85: Manual Rpn Correction
5-4. Manual RPN Correction 5-4. Manual RPN Correction 4. The cursor selection page is displayed as shown below. The CCD RPN (Residual Point Noise) is concealed Adjust the vertical and horizontal lines of the cross- automatically (APR) while the automatic black balance shaped cursor to the RPN by changing the H and V adjustment (ABB) is being executed. -
Page 86: Pre White Clip Level Adjustment (Rom Version 1.30 Or Higher)
5-4. Manual RPN Correction 5-5. Pre White Clip Level Adjustment (ROM Version 1.30 or Higher) 5-5. Pre White Clip Level Adjustment 6. Temporary concealment is executed and the conceal- (ROM Version 1.30 or Higher) ment determination page (CONCEALMENT?) will be displayed as shown below. - Page 87 5-5. Pre White Clip Level Adjustment (ROM Version 1.30 or Higher) Adjustment Procedures 1. Change the gain of the camera by the MASTER GAIN in BLACK SHADING page of the MAINTENANCE menu, and adjust the pre white clip level so that the video level A becomes the specified value for each gain (_3, 0, 3, 6, 12 dB).
-
Page 89: Electrical Alignment
HDVF-700A (HDC-900/910) . Lens Canon HJ18 Fixtures . Pattern box PTB-500 Sony Part No. : J-6029-140-B . Grayscale chart (16 : 9 transparent type) Sony Part No. : J-6394-080-A . Grayscale chart (4 : 3 reflective type) Commercially available . Extension board EX-738 Sony Part No. -
Page 90: How To Make The Cczrgb-3 Cable
. “Section 6-1-8. Initial Settings” must be completed. Parts required 6-1-4. File data at Adjustment . CCZ connector 1 pc (Sony part No.: 1-564-184-21) . BNC connectors 4 pcs (Sony part No.: 1-569-370-11) . 75 Z coaxial cable 4 pcs The file structure of the adjustment data of HDC-900/910 and HDC-950/930 is as follows. -
Page 91: Maintaining The Grayscale Chart
6-1. Preparations 6-1-5. Maintaining the Grayscale Chart For the VA gain adjustment, using an 89.9 %-reflective grayscale chart is preferable. If a reflective chart is not available, use a well-maintained pattern box and a transparent grayscale chart for adjustment. Before beginning adjustment, set the illumination of the light source (or the luminous intensity on the chart surface) properly proceeding as follows and set the color temperature to 3200 K exactly by adjust- ing light. - Page 92 6-1. Preparations Setting luminous intensity (when the transparent chart is used) Equipment: Luminance meter (Minolta LS-110 or equivalent. Calibrated.) 1. Light the pattern box and warm up for about 30 minutes. 2. Place the pattern box where the chart is not exposed to light, such as a darkroom. (Or cover the pattern box with a cover whose inside is painted in black.) 3.
-
Page 93: Description On Setup Menu
6-1. Preparations 6-1-6. Description on Setup Menu How to change the setting values A part of adjustments given in this section uses the setup To enter or cancel the setting value of items, which can be menu. The setup menu consists of the following menus. changed by turning the MENU SELECT control (HDC- Besides there is a TOP menu indicating the entire configu- 900/910) or rotary encoder (HDC-950/930), proceed as... -
Page 94: Connection Of Equipment
6-1. Preparations 6-1-7. Connection of Equipment General Adjustments 2" VF HDVF-20A HD CAMERA HDC-900/910 HDC-950/930 ENG/EFP LENS Waveform monitor HD SERIAL DIGITAL OUT A-ch Y, Pb, Pr R, G, B REMOTE CCA-5 CABLE Color monitor (max. 200m) MASTER SETUP UNIT MSU-700A/750 75 Z *1 : Required only when using MSU-700A/750. -
Page 95: Automatic Adjustment
6-1. Preparations 6-2. Automatic Adjustment 6-2. Automatic Adjustment When adjusting using the Setup menu Set S100-1 to S100-4 switches on the AT-130 board to OFF. MAINTENANCE menu is used to perform the automatic adjustment. . OPERATION menu (Refer to Section 3-5 of the Installation and Maintenance Manual) Page Setting item... -
Page 96: Board Adjustment
6-3. PA-239 Board Adjustment 6-3. PA-239 Board Adjustment 5. White balance adjustment Adjust levels for R, G and B as follows. 6-3-1. PA Balance Adjustment Test point/ Adj. point/ EX-738 board PA-239 board Equipment: Oscilloscope 1RV101 R-ch TP22 Object: Grayscale chart 1RV201 G-ch TP14... -
Page 97: Pa Gain Adjustment
6-3. PA-239 Board Adjustment 6-3-2. PA Gain Adjustment Adjustment Procedures 1. PA OUT R level adjustment For the PA gain adjustment, using an 89.9%-reflective Measuring point : TP22/EX-738 board Adjusting point : 1RV103/PA-239 board grayscale chart is preferable. A = 400 ± 10 mV Before beginning adjustment, be sure to set the illumina- Specification : tion of the light source (or the lumirous intensity on the... -
Page 98: Rpn Adjustment
6-3. PA-239 Board Adjustment 6-4. VA-196 Board Adjustment 6-4. VA-196 Board Adjustment 6-3-3. RPN Adjustment 6-4-1. VA Gain Adjustment Preparations . Adjust the monitor manually for a clearer view. . Setting for MSU-700A For the VA gain adjustment, using an 89.9%-reflective CLOSE button →... -
Page 99: Video System Level Adjustment (When Using The Setup Menu)
6-4. VA-196 Board Adjustment 6-5. Video System Level Adjustment (When using the Setup Menu) 6-5. Video System Level Adjustment Adjustment Procedures (When using the Setup Menu) 1. VA OUT R level adjustment Measuring point : TP21/EX-738 board Adjusting point : 1RV200/VA-196 board . - Page 100 6-5. Video System Level Adjustment (When using the Setup Menu) . Call the file in accordance with the lens attached. 3. Perform the adjustments for G-ch and B-ch with the Menu setting: same procedures as for R-ch. MENU: FILE 4. Adjust the white balance. AUTO W/B BAL switch (front panel) →...
-
Page 101: H/V Ratio Adjustment
6-5. Video System Level Adjustment (When using the Setup Menu) 6-5-2. H/V Ratio Adjustment Adjustment for Lens Extender/Shrinker When using the lens extender or lens shrinker, perform the Equipment: Waveform monitor (R, G, B) following adjustments after the completion of lens file Test Point: HD SERIAL DIGITAL OUT connector store. -
Page 102: Detail Level Adjustment
6-5. Video System Level Adjustment (When using the Setup Menu) 6-5-3. Detail Level Adjustment 6-5-4. Crispening Adjustment Equipment: Waveform monitor (R, G, B) Equipment: Waveform monitor (R, G, B) Test Point: HD SERIAL DIGITAL OUT connector Test Point: HD SERIAL DIGITAL OUT connector Object: Grayscale chart Object:... -
Page 103: Level Dependent Adjustment
6-5. Video System Level Adjustment (When using the Setup Menu) 6-5-5. Level Dependent Adjustment 6-5-6. Detail Clip Adjustment Equipment: Waveform monitor (R, G, B) Equipment: Waveform monitor (R, G, B) Test Point: HD SERIAL DIGITAL OUT connector Test Point: HD SERIAL DIGITAL OUT connector Object: Grayscale chart Object:... -
Page 104: Auto-Iris Adjustment
6-5. Video System Level Adjustment (When using the Setup Menu) 6-5-7. Auto-iris Adjustment 3. Adjust the white limiter. Adjustment item: MENU: PAINT Equipment: Waveform monitor (R, G, B) PAGE: DETAIL 1 Test Point: HD SERIAL DIGITAL OUT connector ITEM: LIMITER WHT Object: Grayscale chart Specification:... -
Page 105: Pedestal Level Adjustment
6-5. Video System Level Adjustment (When using the Setup Menu) 6-5-8. Pedestal Level Adjustment 6-5-9. Flare Adjustment Equipment: Waveform monitor (R, G, B) Equipment: Waveform monitor (R, G, B) Test Point: HD SERIAL DIGITAL OUT connector Test Point: HD SERIAL DIGITAL OUT connector Object: Grayscale chart Preparations... -
Page 106: Gamma Correction Adjustment
6-5. Video System Level Adjustment (When using the Setup Menu) 6-5-10. Gamma Correction Adjustment 6-5-11. Knee Point/Knee Slope Adjustment Equipment: Waveform monitor (R, G, B) Equipment: Waveform monitor (R, G, B) Test Point: HD SERIAL DIGITAL OUT connector Test Point: HD SERIAL DIGITAL OUT connector Object: Grayscale chart Preparations... -
Page 107: White Clip Level Adjustment
6-5. Video System Level Adjustment (When using the Setup Menu) 6-5-12. White Clip Level Adjustment 3. Adjustment item: MENU: PAINT PAGE: KNEE Equipment: Waveform monitor (R, G, B) ITEM: SLOPE Test Point: HD SERIAL DIGITAL OUT connector Specification: Adjust the cross points B of the gray scale for preferred level for Preparations R, G and B respectively. -
Page 108: File Store
6-5. Video System Level Adjustment (When using the Setup Menu) 6-6. Video System Level Adjustment (When using MSU) 6-6. Video System Level Adjustment 6-5-13. File Store (When using MSU) After adjustments described in Section 6-5 are complete, be sure to execute the reference file store. . - Page 109 6-6. Video System Level Adjustment (When using MSU) Adjustment Procedures Adjustment for Lens Extender/Shrinker 1. Adjust the white balance. When using the lens extender or lens shrinker, perform the WHITE button/MSU-700A → ON (lit) following adjustments after the completion of lens file 2.
-
Page 110: H/V Ratio Adjustment
6-6. Video System Level Adjustment (When using MSU) 6-6-2. H/V Ratio Adjustment 6-6-3. Detail Level Adjustment Equipment: Waveform monitor (R, G, B) Equipment: Waveform monitor (R, G, B) Test Point: HD SERIAL DIGITAL OUT connector Test Point: HD SERIAL DIGITAL OUT connector Object: Grayscale chart Object:... -
Page 111: Crispening Adjustment
6-6. Video System Level Adjustment (When using MSU) 6-6-4. Crispening Adjustment 6-6-5. Level Dependent Adjustment Equipment: Waveform monitor (R, G, B) Equipment: Waveform monitor (R, G, B) Test Point: HD SERIAL DIGITAL OUT connector Test Point: HD SERIAL DIGITAL OUT connector Object: Grayscale chart Object:... -
Page 112: Detail Clip Adjustment
6-6. Video System Level Adjustment (When using MSU) 6-6-6. Detail Clip Adjustment 3. Adjust the white limiter. MSU menu operation: . PAINT button → ON (lit) Equipment: Waveform monitor (R, G, B) . Touch panel operation Test Point: HD SERIAL DIGITAL OUT connector (Page 1/3) →... -
Page 113: Auto-Iris Adjustment
6-6. Video System Level Adjustment (When using MSU) 6-6-7. Auto-iris Adjustment 6-6-8. Pedestal Level Adjustment Equipment: Waveform monitor (R, G, B) Equipment: Waveform monitor (R, G, B) Test Point: HD SERIAL DIGITAL OUT connector Test Point: HD SERIAL DIGITAL OUT connector Object: Grayscale chart Preparations... -
Page 114: Flare Adjustment
6-6. Video System Level Adjustment (When using MSU) 6-6-9. Flare Adjustment 6-6-10. Gamma Correction Adjustment Equipment: Waveform monitor (R, G, B) Equipment: Waveform monitor (R, G, B) Test Point: HD SERIAL DIGITAL OUT connector Test Point: HD SERIAL DIGITAL OUT connector Object: Grayscale chart Object:... -
Page 115: Knee Point/Knee Slope Adjustment
6-6. Video System Level Adjustment (When using MSU) 6-6-11. Knee Point/Knee Slope Adjustment 3. MSU menu operation: . Touch panel operation (Page 2/3) → [Knee|Slope] Equipment: Waveform monitor (R, G, B) Test Point: HD SERIAL DIGITAL OUT connector Adjustment Item: R, G, B Master Specification: Adjust the cross points B of the gray scale for preferred level for... -
Page 116: White Clip Level Adjustment
6-6. Video System Level Adjustment (When using MSU) 6-6-12. White Clip Level Adjustment 6-6-13. File Store Equipment: Waveform monitor (R, G, B) After adjustments described in Section 6-6 are complete, Test Point: HD SERIAL DIGITAL OUT connector be sure to execute the reference file store. 1. -
Page 117: Adjustment After Replacement Of Nd Filter
6-7. Adjustment After Replacement of ND Filter 6-7. Adjustment After Replacement of OHB File Store ND Filter 1. MSU menu operation: . FILE button → ON (lit) When the filter disk unit or the ND filter alone in the filter . -
Page 118: Filter Positioning Adjustment
6-8. Filter Positioning Adjustment 6-8. Filter Positioning Adjustment Note . This adjustment is required only when replacing the CCD unit or the filter drive board. Preparation . S1/Filter drive board → ON (upper side) Adjustment Procedures 1. ND 1 button/MSU-700 → ON 2. - Page 120 HKC-T950 (SY) HDC-900 (SY) HDC-900/L (J) HDC-910 (UCJ, CE) HDC-910/L (J) HDC-930 (SY) Printed in Japan Sony Corporation HDC-950 (JN, SY) J, E 2003. 11 08 B&P Company 9-968-560-05 ©2000...