Table of Contents
Advertisement
CAUTION:
Leave all power switches off and all power cords unplugged until all audio/video con-
nections have been completed.
Notes:
Connect to monitor
|]
TV set equipped
with pin jack
terminal.
INPUT BALANCE Control
Adjust
input balance
when
in DSP
Dolby Surround mode.
(Example of DAT deck connection)
To IN
==
terminal
_—
From
OUT
—_
terminal
|
ouT
IN
DIGITAL
Direct digital connections to CD player,
DBS
tuner, and DAT deck equipped
with digital output terminals.
Caution
Input/output optical fiber terminals not possible
1. Only video signals are handled by 21P terminals. For audio signals, use IN/OUT at <ANALOG AUDIO > terminals.
2. If video signals output from this set are monitored using both pin jack and 21P terminals at the same time, the
pictures may result in poor quality. Therefore,
use either terminal at one time.
3. If signals via pin jack terminals cannot be monitored using 21P terminals, monitor using pin jack terminals or
set the TV/VCR
switch to VCR position on the VCRs connected
via 21P terminals
Connect to
monitor TV set
equipped with
21P terminal
PY) grom
<MONITOR>
Connect a third VCR or video movie unit to the front panel
jacks. (only for playback)
Example of connection
Use either control terminal
= SYSTEM CONTROL
If dedicated mini-plugs connect this unit to optional
Fe haihcteerninals
TOSHIBA's
components,
such
as_
tuner
(ST-5528/5538),
tape
deck
(PC-5858),
and
turntable
(SR-5638),
the whole
system
can
be
controlled by the provided remote control unit. (See
the section on using the remote control unit for
oe
details.)
mn
SS
This unit
Other components
= Speaker positions and connections
® BTL connection
Connect to
Connect to
S
R
:
oe ou
oe Pe
eae pantie to is a
pies
ee
Ensure that speaker polarity is matched with amplifi-
:
ae [ y
tne mign: powe
PUL Or
ie:
Arena Nie
er polarity by connecting plus (+) speaker cables to
RS
PUNEr:
red speaker terminals, and minus (—) speaker cables
es.
ae
to black speaker terminals.
Use speakers with im-
<VCR 2>
<VCR 1>
pedance in the 6 to 16 ohms range.
Expose about
10mm
of lead
Twist the lead wires
firmly together, insert
=
into the speaker ter-
minal aperture, and
then tighten firmly by
turning clockwise.
———
SYSTEM
tot CONTROL
®@
<_
©)
MONITOR
OUT
@
<MONITOR >
<VCR 2>
AGB 21P CONNECTOR
TAPE 2/(0AT>y—<
TAPE
1>.
<TUNER>
le d/o el6/e/e
© ele|efo|ejo
dle:
ax
SKILL
SEDC
| |
(Example
of VCR 1
speakers
(Example of
TAPE
1
connection)
(Example of
graphic équalizer
connection to
To IN
terminal
To IN
From OUT
terminal
j|terminal
(REC)
(PLAY)
Connect to graphic
®@ Speaker positions
{ ©#l4
_sequalizer or other
audio component.
IN
OUT
IN
OUT
orm"
por
LINE
Signals to which DSP effect is ap-
plied for FRONT
and REAR
are
Since this unit is a 4-channel amplifier designed
to drive independent front and rear speakers,
position the speakers as indicated in the illus-
tration upon to get the most effective results
with natural soundfield playback. Although good
results can be obtained even when small mini
speakers are used as the rear speakers, adjust
Connect
to
TV/DBS
Connect to DAT deck, tape deck,
tuner,
VD/CDV
=
tae
output from the
<ADAPTOR>
ty
cording
to preference,
connect
tones or to those of a power am-
terminals. But do not plug these pins into any other terminal under any circumstance
plifier using this unit as a pre-
(since this can result in failure). If not using the <ADAPTOR>
terminals, make sur:
amplifier.
that the shorting pins are plugged in as shown in the diagram. Incorrect insertio:
may prevent output of sound.
—10—
connect GND terminals as well.
Advertisement
Table of Contents
