Figure 8-7. Attaching Battery - Vacuum Port Seal; Figure 8-8. Attaching Battery - Slide Into Position; Figure 8-18. Remove Flex Connectors And Expansion Board Assembly; Figure 8-19. Remove Antenna Coax Cable Connector - Motorola APX 5000 Service Manual

Sec 2: 12 List of Figures
Figure 8-5. Removing the Antenna ...................................................................................................... 2:8-7
Figure 8-6. Attaching Battery – Battery Seal ........................................................................................ 2:8-8
Figure 8-7. Attaching Battery – Vacuum Port Seal ............................................................................... 2:8-9
Figure 8-8. Attaching Battery – Slide into Position ............................................................................... 2:8-9
Figure 8-9. Squeezing the Release Latches ...................................................................................... 2:8-10
Figure 8-10. Removing the Battery ...................................................................................................... 2:8-10
Figure 8-11. Removing the Thumb Screw............................................................................................ 2:8-11
Figure 8-12. Engaging Hook and Seating Cover.................................................................................. 2:8-12
Figure 8-13. Securing the Cover .......................................................................................................... 2:8-12
Figure 8-14. Remove Center Screws ................................................................................................... 2:8-13
Figure 8-15. Remove Bottom Screws................................................................................................... 2:8-13
Figure 8-16. Remove Top Screws ........................................................................................................ 2:8-14
Figure 8-17. Remove Speaker Module................................................................................................. 2:8-14
Figure 8-18. Pull Expander Board Support (Opt. Expansion Board) .................................................... 2:8-15
Figure 8-19. Remove Expander Board Support ................................................................................... 2:8-15
Figure 8-20. Remove Flex Connectors and Expansion Board Assembly............................................. 2:8-16
Figure 8-21. Remove Antenna Coax Cable Connector ........................................................................ 2:8-16
Figure 8-22. Remove Housing ............................................................................................................. 2:8-17
Figure 8-23. Remove Back Chassis Assembly from Main Chassis Assembly ..................................... 2:8-17
Figure 8-24. Remove RF Board Screw ................................................................................................ 2:8-18
Figure 8-25. Remove RF Board Assembly........................................................................................... 2:8-18
Figure 8-26. Remove VOCON Board Screw ........................................................................................ 2:8-19
Figure 8-27. Remove VOCON Board Assembly .................................................................................. 2:8-19
Figure 8-28. Remove Knobs ................................................................................................................ 2:8-20
Figure 8-29. Remove Control Top Assembly........................................................................................ 2:8-20
Figure 8-30. Serviceable Components – Main Chassis Assembly....................................................... 2:8-21
Figure 8-31. Remove Chassis Ground Contact.................................................................................... 2:8-22
Figure 8-32. Control Top Assembly and Control Top Seal.................................................................... 2:8-23
Figure 8-33. VOCON Board Assembly................................................................................................. 2:8-23
Figure 8-34. RF Board Assembly ......................................................................................................... 2:8-24
Figure 8-35. Expansion Board Assembly ............................................................................................. 2:8-25
Figure 8-36. Back Chassis Assembly (Dual Display Versions) ............................................................ 2:8-25
Figure 8-37. Back Chassis Assembly (Top Display Version)................................................................ 2:8-27
Figure 8-38. Main Housing Assembly (Dual Display Version, Full Keypad) ......................................... 2:8-29
Figure 8-39. Main Housing Assembly (Dual Display Version, Limited Keypad) ................................... 2:8-29
Figure 8-40. Main Housing Assembly (Top Display Version)................................................................ 2:8-30
Figure 8-41. Speaker Module ............................................................................................................... 2:8-31
Figure 8-42. Speaker Grille Assembly .................................................................................................. 2:8-31
Figure 8-43. Control Top Bezel Assembly ............................................................................................ 2:8-32
Figure 8-44. Knobs Assembly .............................................................................................................. 2:8-32
Figure 8-45. Insert VOCON Board ....................................................................................................... 2:8-33
Figure 8-46. Connect RF Board to VOCON Board............................................................................... 2:8-34
Figure 8-47. Place Back Chassis ......................................................................................................... 2:8-35
Figure 8-48. Place Housing into Main Chassis..................................................................................... 2:8-36
Figure 8-49. Assemble Expansion Board Assembly ............................................................................ 2:8-36
Figure 8-50. Insert Flex Connectors ..................................................................................................... 2:8-37
Figure 8-51. Expander Board Support (61) .......................................................................................... 2:8-37
Figure 8-52. Insert Expander Board Support........................................................................................ 2:8-37
Figure 8-53. Press Expander Board Support into Place (Opt. Expansion Board) ................................ 2:8-38
Figure 8-54. Insert Speaker Module ..................................................................................................... 2:8-38
Figure 8-55. Insert Top Screws ............................................................................................................ 2:8-39
Figure 8-56. Insert Center Screws ....................................................................................................... 2:8-39
Figure 8-57. Insert Bottom Screws ....................................................................................................... 2:8-40
Figure 8-58. Attaching Vacuum Adapter............................................................................................... 2:8-42