Advertisement
Table of Contents
- 1 Table of Contents
- 2 Welcome / Package Contents
- 3 Override Access Key / Install Batteries
- 4 Low or Dead Batteries / Testing Digital Lock
- 5 Programming New User Code / Testing New User Code
- 6 Closing Your Safe / Turn Sound on and off / Motion Alarm Settings
- 7 Care and Maintenance
- 8 Anchoring Your Safe
- 9 Consumer Assistance
- 10 Digital User Code Record
- Download this manual
Advertisement
Table of Contents
Related Manuals for Honeywell 2605
Summary of Contents for Honeywell 2605
- Page 1 ENGLISH Operation & Installation Guide Steel Waterproof Fire Safe with Programmable Digital Lock Model 2605 Read this manual carefully and never store it inside the safe!
-
Page 2: Table Of Contents
Index Welcome / Package Contents ................ Page 1 Page 2 Override Access Key / Install Batteries............Low or Dead Batteries / Testing Digital Lock..........Page 3 Programming New User Code / Testing New User Code......Page 4 Page 5 Closing Your Safe / Turn Sound On and Off / Motion Alarm Settings..Secure Lockout Period / Lost or Forgotten User Codes / Page 6 Care and Maintenance.................. -
Page 3: Welcome / Package Contents
WELCOME Your Honeywell Waterproof Steel Fire and Security Safe will provide years of safe and secure protection for your valuables, important documents and other personal items. All Honeywell safes are designed and built using the highest manufacturing standards to ensure maximum user satisfaction under a variety of conditions. -
Page 4: Override Access Key / Install Batteries
OVERRIDE ACCESS KEY Your safe is equipped with an override access key which allows immediate access in case you forget your user codes or the batteries need to be installed or replaced. 1. Remove override access rubber lock cover (Figure 1). 2. -
Page 5: Low Or Dead Batteries / Testing Digital Lock
LOW OR DEAD BATTERIES The battery level meter is located at the top of the keypad. You can check the battery level meter by pressing the key. If it is down to the last red LED on the left of the meter, it is an indicator that the batteries are weak and must be changed immediately. -
Page 6: Programming New User Code / Testing New User Code
PROGRAMMING NEW USER CODE For best security, it is recommended that you immediately change the factory preset code to your own personal user code. Programming the User Code 1. Locate and press the inset program button located on the top inside edge of the door (Figure 1). The red and green LED’s will flash and you will have 10 seconds to perform the next 2 steps. -
Page 7: Closing Your Safe / Turn Sound On And Off / Motion Alarm Settings
CLOSING YOUR SAFE To Lock: 1. Close the safe door and turn handle downward to the left placing the door bolts into the locked position (Figure 1 and Figure 2). Note: Due to the airtight seal, to close you may have to push inward on the door while turning the handle downward clockwise to place the blots fully into the locked position. -
Page 8: Care And Maintenance
SECURE LOCKOUT PERIOD If the wrong user code is entered into the keypad 3 consecutive times in a row, the keypad will automatically go into lockout mode and you will not be able to open the safe using the digital keypad for 15 minutes. -
Page 9: Anchoring Your Safe
ANCHORING YOUR SAFE You may bolt your safe to a shelf or floor for added theft protection and resistance to tipping. Your safe has a pre-drilled bolt-down hole in the floor panel and mounting hardware is provided for securing to concrete surfaces. -
Page 10: Consumer Assistance
CONSUMER ASSISTANCE EMAIL: LHLPCustomerService@LHLPinc.com WEBSITE: www.honeywellsafes.com ADDRESS: Consumer Assistance Dept. LH Licensed Products, Inc. 860 East Sandhill Avenue Carson, CA 90746 USA TELEPHONE: US/Canada 1-877-354-5457 (Toll Free) Mexico 01-800-288-2872 After English voice recording stops you must then enter 800-860-1677 to complete your call. (Toll Free) Australia 0011-800-5325-7000 (Toll Free) Germany/New Zealand 00-800-5325-7000 (Toll Free) Other Countries XX*-310-323-5722 (Toll Charges Apply) -
Page 11: Digital User Code Record
ORDERING ADDITIONAL OVERRIDE ACCESS KEYS The following information is required to order keys: 1. PROOF OF OWNERSHIP (1 of 2 Options Below) A) SALES RECEIPT & IDENTIFICATION – INTERNATIONAL ORDERS ONLY! • Copy of sales receipt showing Store, Date & Product Description. •... - Page 12 Manufactured by: LH Licensed Products, Inc. 860 East Sandhill Avenue Carson, CA 90746 The Honeywell Trademark is used under license from Honeywell International Inc. Honeywell International Inc. makes no representations or warranties with respect to this product. M2605E-20150904 www.honeywellsafes.com...