Location Requirements - Maytag MGT3800XW3 Installation Instructions Manual

LOCATION REQUIREMENTS
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Do not install in a garage.
Failure to do so can result in death, explosion, or fire.
Select proper location for your washer to improve performance
and minimize noise and possible "washer walk." Install your
washer in a basement, laundry room, closet, or recessed area.
You will need:
[] A location that allows for proper exhaust installation.
A gas washer/dryer must be exhausted to the outdoors.
See "Venting Requirements."
[] A grounded electrical outlet located within 2 ft (610 mm) of
either side of the washer/dryer. See "Electrical Requirements."
[] A separate 15- or 20-amp circuit.
[] A sturdy floor to support the washer/dryer weight (washer/
dryer, water, and load) of 500 Ibs (226.8 kg).
[] A level floor with a maximum slope of 1" (25 mm) under entire
washer/dryer. Clothes may not tumble properly and automatic
sensor cycles may not operate correctly if washer/dryer is not
level. Installing on carpet is not recommended.
[] A water heater set to deliver 120°F (49°C) water to the washer.
[] Hot and cold water faucets located within 4 ft (1.2 m) of the
hot and cold water fill valves, and water pressure of 5-100 psi
(34.5-689.6 kPa).
The washer/dryer must not be installed or stored in an area where
it will be exposed to water and/or weather.
Do not operate your washer in temperatures at or below 32°F
(0°C). Some water can remain in the washer and can cause
damage in low temperatures. See "Washer/Dryer Care" in the
Washer/Dryer Use and Care Guide for winterizing information.
Do not operate your dryer at temperatures below 45°F (7°C). At
lower temperatures, the dryer might not shut off at the end of an
automatic cycle. This can result in longer drying times.
Check code requirements. Some codes limit, or do not permit,
installation of the washer/dryer in garages, closets, mobile
homes, or sleeping quarters. Contact your local building
inspector.
Recessed area or closet installation
48 in.2
(310 cm2)
Front
View
24 in.2
(155 cm2)
Closet
door
O
3"
(76 mr
The spacing dimensions above are recommended for this
washer/dryer. This washer/dryer has been tested for spacing of
0" (0 mm) clearance on the sides. Recommended spacing should
be considered for the following reasons:
[] Additional spacing should be considered for ease of
installation and servicing.
[] Additional clearances might be required for wall, door, and
floor moldings.
[] Additional spacing on all sides of the washer/dryer is
recommended to reduce noise transfer.
[] For closet installation, with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
NOTE: No other fuel-burning appliance can be installed in the
same closet as a dryer.
Mobile home = additional installation requirements
This washer/dryer is suitable for mobile home installations.
The installation must conform to the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280) or the Canadian
Manufactured Home Standard, CAN/CSA-Z240 MH.
Mobile home installations require:
[] Metal exhaust system hardware, which is available for
purchase from your dealer.
[] Mobile Home Installation Kit Part Number 346764. See "Tools
and Parts" section for information on ordering.
[] Special provisions must be made in mobile homes to
introduce outside air into the dryer. The opening (such as a
nearby window) should be at least twice as large as the dryer
exhaust opening.
6