Advertisement
Quick Links
Cordless Impact Driver
capamttes
1
High
tensile
bolt
M a c h i n e
screw
Standard
bolt
4
m m
8
mm
15/32"
~
5/16")
5
m m
12
m m
13/16"
112"l
5
m m
-
1 0
m m
13/16"
~
318")
Equipted with Electric Brake
MODEL 6911D
MODEL 6911DW
With Fast Charger
No
load
s p e e d
(RPMI
0
~
1,800
INSTRUCTION MANUAL
M a x fastening torque
(See note 1
below1
Impacts
per
minute
0
-
2 . 5 0 0
1 , 0 0 0
kg.cm
171 f t lbsl
Net
wesght
Dimensions
1 L
x
W
x HI
2 2 1
mm
x
7 9
m m
x
230
mm
18~314"
x
3 118''
x
9 " l
1.8
kg
14 0 lbsl
12
v
I
A C o n l v 5 0 H r - 6 0 H z
I
D C 9 6 V 1 2 V
I
1
Hr
-
Battery
Cartridge 1200
Voltage
Note 1. After fastening high tensile bolt M14 (F1 1 T l for
3
seconds whlle using a fully charged battery cartridge
2 . Manufacturer reserves the right to change specifications without notice.
3.
Specifications may differ from country t o country.
*
Model DC1290 Fast Charger
Input
I
OUtPUt
Charging time
Advertisement
Related Manuals for Makita 6911D
Summary of Contents for Makita 6911D
- Page 1 2 2 1 171 f t lbsl kg.cm 18~314" Input D C 9 6 V 1 2 V seconds whlle using a fully charged battery cartridge MODEL 6911D MODEL 6911DW With Fast Charger load (RPMI High bolt tensile 13/16"...
-
Page 2: Important Safety Instructions
SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. - Page 3 REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don‘t carry plugged-in tool with finger on switch. Be sure switch is 16.
- Page 4 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Length of Cord (Feet) AWG Size of Cord Do not operate charger w i t h damaged cord or plug - replace them im- mediately. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way;...
-
Page 5: Additional Safety Rules
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE not charge Battery Cartridge when temperature is BELOW or ABOVE 4OoC ( 1 0 4 O F ) . 2. Do not attempt to use a step-up transformer, an engine generator or receptacle. - Page 6 Installing or removing battery cartridge Always switch off the tool before insertion or removal of the battery cartridge. *To remove the battery cartridge, pull out plate on the tool and grasp both sides of the cartridge while withdrawing it from the tool. *To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into...
- Page 7 Use only the driver bit or socket bit shown in the figure. not use any other driver bit or socket bit. To install the bit, pull the direction of the arrow and insert the bit into the it will go. Then sleeve as release the sleeve to secure the bit.
- Page 8 Switch action Tool speed i s increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop. CAUTION : Before inserting the battery cartridge into the tool, always check to see that the trigger switch actuates properly and returns to the "OFF"...
- Page 9 Operation The proper fastening torque may differ depending upon the kind or type of material to be fastened, etc. The relation between fastening torque time shown in the figures below. Machine screw Kg . c m Ibs) ( f t (15) ‘E Standard bolt...
- Page 10 High tensile bolt ( f t Ibs) (57) (43) (29) (15) Hold the tool firmly and place the point of the driver bit in the screw head. Apply for- ward pressure to the tool to the extent that the bit will not slip off the screw and turn the tool on to start operation.
- Page 11 3. Bolt Even though the torque coefficient and the class of bolt are the same, the proper fastening torque will differ according to the diameter of .Even though the diameters of bolts are the same, the proper fastening torque will differ according to the torque coefficient, the class of bolt and the bolt length.
-
Page 12: Maintenance
Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. - Page 13 ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury t o persons. The accessories or attachments should be used only in the proper and intended manner.
-
Page 14: Cordless Impact Driver
A m - 1 4 - ' 9 2 CORDLESS IMPACT DRIVER Model 6911D Note: The switch and other part configurations may differ from country to country. - Page 15 MODEL 6911D 'itM DESCRIPTION MACHINE N a m e Plate Tapping Screw B T 4 x 2 0 Pan Head Screw M a x 2 0 IWith Washer1 Houslnq Set IWith Item 291 s e t Plate S w i t c h Lever...
- Page 16 MAKITA Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.