Advertisement
Quick Links
Cordless Angle Drill
Capacities
SteelIWood
Wood screw
No load speed
700
Rimin
4 5
mm x
2 0
mm
13/16"
x
3/4"1
10 mm 13/8"1
10
mm
(3/8")
MODEL DA3000D
10 mm (3/8") MODEL DA3000DW
With Fast Charger
Net weight
Overall length
1
2 kg
12 6 lbsl
290
mm 11 1-3/8"1
INSTRUCTION MANUAL
Battery Cartridge
7000
Voltage
Charging
time
7 2 V
1 Hr.
SPEC IF I CAT10 N S
M o d e l
DC7100
Fast Charger
Dimensions
Net
1L
x
W
x
H I
weight
A.C. only
0 . C
1 4 5 mm
x
80
mm x 61 mm
0 7 kg
input
OUtPUt
5 0
H2
60 Hr
7 2 V
15
3/4"
x
3~118"
x
2 ~ 3 / 8 " )
11
5 lbsl
M o d e l
DA3000D
Advertisement
Related Manuals for Makita DA3000D
Summary of Contents for Makita DA3000D
- Page 1 DC7100 Fast Charger input OUtPUt A.C. only 0 . C 1 4 5 mm 60 Hr 7 2 V MODEL DA3000D With Fast Charger Net weight Overall length 2 kg 12 6 lbsl mm 11 1-3/8"1 Dimensions weight 0 7 kg mm x 61 mm 3/4"...
-
Page 2: Important Safety Instructions
SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. - Page 3 REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turn- AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and STAY ALERT.
- Page 4 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Length of Cord (Feet) AWG Size of Cord not operate charger with damaged cord or plug mediately. Do not operate charger if wise damaged in any way; take it t o a qualified serviceman. Do not disassemble charger or battery cartridge;...
- Page 5 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. Do not allow anything t o cover or clog the charger vents. 4.
- Page 6 Installing or removing battery cartridge Always switch off the tool before insertion or removal of the battery cartridge. To remove the battery cartridge, pull out plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel. *To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and...
- Page 7 Installing and removing bit CAUTION : Be sure that the battery cartridge has been removed from the tool. install the drill bit, place it in the chuck as it will go. Tighten the chuck collar by hand. Place the chuck key in each of three holes, and tighten clockwise.
- Page 8 Switch action the reversing switch lever just in front o s e t of the trigger switch to Forward (FWD) or Reverse (REV). Then pull the trigger to turn the tool ON and release it to turn OFF. To change the direction of bit rotation, release the trigger, come to complete stop, and then slide...
- Page 9 cutting lubricant on the bit to facili- drilling if necessary. tate Screwdriving Phillips bits Select your screws and nominal dia- meter with the chart on the right. Slotted bits Select a slotted bit to match the slot on the screw heads. If the bit is too small for the screw slot, the bit and/or screw head may be damaged.
- Page 10 Hole .The hole on the heel of the tool is a con- venient way to carry it by a cord, hook or other means. Hole...
-
Page 11: Maintenance
Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. - Page 12 ACCESS0 R I ES CAUTION : These accessories or attachments are recommended for use w i t h your Makita tool specified in this manual. The of any other accessories or attachments might present a risk The accessories or attachments...
- Page 13 Steel case 181697-5 Part...
- Page 14 Sep-19284 (3/8") CORDLESS ANGLE DRILL Model DA3000D Note: The switch and other part configurations may differ from country to country.
- Page 15 MODEL OA30000 ' i k M DESCRIPTION 5 1 0 Orill Chuck Ring Plane Bearing Housing IWnh Item Holder Gear 0earmg 4 Plane Current Relay Note: The switch and other part specifications , , ! & DESCRIFTION Switch Motor tioUSlng Name Plate Screw M4x22 [With Washer1 Battery...
- Page 16 MAKITA LIMITED ONE YEAR WARRANTY Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.